LG Wall-Mounted Air Conditioner Instructions and Remote Button Help

OWNER’S MANUAL AIR CONDITIONER
Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times.

TYPE: WALL MOUNTED
MFL69781201
Rev.01_041817

SAFETY INSTRUCTIONS

The following safety guidelines are intended to prevent unforeseen risks or damage from unsafe or incorrect operation of the appliance.
The guidelines are separated into ‘WARNING’ and ‘CAUTION’ as described below.

This symbol is displayed to indicate matters and operations that can cause risk. Read the part with this symbol carefully and follow the instructions in order to avoid risk.
WARNING – This indicates that the failure to follow the instructions can cause serious injury or death.

CAUTION – This indicates that the failure to follow the instructions can cause the minor injury or damage to the product.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of explosion, fire, death, electric shock, injury or scalding to persons when using this product, follow basic precautions, including the following:
Children in the Household
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Installation

• Do not install the air conditioner on an unstable surface or in a place where there is danger of it falling.
• Contact an authorized service center when installing or relocating the air conditioner.
• Install the panel and the cover of the control box safely.
• Do not install the air conditioner in a place where flammable liquids or gases such as gasoline, propane, paint thinner, etc., are stored.
• Make sure that the pipe and the power cable connecting the indoor and outdoor units are not pulled too tight when installing the air conditioner.
• Use standard circuit breaker and fuse that conform to the rating of the air conditioner.
• Do not input air or gas into the system except with the specific refrigerant.
• Use non-flammable gas (nitrogen) to check for leak and to purge air; using compressed air or flammable gas may cause fire or explosion.
• The indoor/outdoor wiring connections must be secured tightly, and the cable should be routed properly so that there is no force pulling the cable from the connection terminals. Improper or loose connections can cause heat generation or fire.
• Install dedicated electric outlet and circuit breaker before using the air conditioner.
• Do not connect the ground wire to a gas pipe, a lightning rod, or a telephone ground wire.

Operation

• Be sure to use only those parts listed in the service parts list. Never attempt to modify the equipment.
• Make sure that children do not climb on or hit the outdoor unit.
• Dispose of the batteries in a place where there is no danger of fire.
• Use only the refrigerant specified on the air conditioner label.
• Cut off the power supply if there is any noise, smell, or smoke coming from the air conditioner.
• Do not leave flammable substances such as gasoline, benzene, or thinner near the air conditioner.
• Contact an authorized service center when the air conditioner is submerged by flood waters.
• Do not use the air conditioner for an extended period of time in a small place without proper ventilation.
• In the event of a gas leak (such as Freon, propane gas, LP gas, etc.) ventilate sufficiently before using the air conditioner again.
• To clean the interior, contact an authorized service center or dealer. Using harsh detergents may cause corrosion or damage to the unit.
• Be sure to ventilate sufficiently when the air conditioner and a heating appliance such as a heater are used simultaneously.
• Do not block the inlet or outlet of air flow.
• Do not insert hands or other objects through the air inlet or outlet while the air conditioner is operating.
• Make sure that the power cable is neither dirty, loose, nor broken.
• Never touch, operate, or repair the air conditioner with wet hands.
• Do not place any objects on the power cable.
• Do not place a heater or other heating appliances near the power cable.
• Do not modify or extend the power cable. Scratches or peeling insulation on the power cables may result in fire or electric shock, and should be replaced.
• Cut off the power supply immediately in the event of a blackout or a thunderstorm.
• Take care to ensure that power cable could not be pulled out or damaged during operation.
• Do not touch refrigerant pipe or water pipe or any internal parts while the unit is operation or immediately after operation.

Maintenance

• Do not clean the appliance by spraying water directly onto the product.
• Before cleaning or performing maintenance, disconnect the power supply and wait until the fan stops.

Technical Safety

• Installation or repairs made by unauthorized persons can pose hazards to you and others.
• The information contained in the manual is intended for use by a qualified service technician who is familiar with the safety procedures and equipped with the proper tools and test instruments.
• Failure to read and follow all instructions in this manual can result in equipment malfunction, property damage, personal injury and/or death.
• The appliance shall be installed in accordance with national wiring regulations.
• When the power cord is to be replaced, the replacement work shall be performed by authorized personnel using only genuine replacement parts.
• This appliance must be properly grounded to minimize risk of electric shock.
• Do not cut or remove the grounding prong from the power plug.
• Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal, uninsulated, and the wall receptacle is grounded through house wiring.
• If you have any doubt whether the air conditioner is properly grounded, have the wall receptacle and circuit checked by a qualified electrician.
• The refrigerant and insulation blowing gas used in the appliance require special disposal procedures. Consult a service agent or a similarly qualified person before disposing of them.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard.

CAUTION
To reduce the risk of minor injury to persons, malfunction, or damage to the product or property when using this product, follow basic precautions, including the following:
Installation

• Do not install the air conditioner in an area where it is directly exposed to sea wind (salt spray).
• Install the drain hose properly for the smooth drainage of water condensation.
• Exercise caution when unpacking or installing the air conditioner.
• Do not touch the leaking refrigerant during installation or repair.
• Transport the air conditioner with two or more people or use a forklift.
• Install the outdoor unit such that it is protected from direct sunlight. Do not place the indoor unit in a place where it is directly exposed to sunlight via the windows.
• Safely dispose of packing materials such as screws, nails or batteries using proper packaging after installation or repair.
• Install the air conditioner in a place where the noise from the outdoor unit or the exhaust fumes will not inconvenience the neighbors. Failure to do so may result in conflict with the neighbors.

Operation

• Remove the batteries if the remote control is not to be used for an extended period of time.
• Make sure that the filter is installed before operating the air conditioner.
• Be sure to check if there is a refrigerant leak after installing or repairing the air conditioner.
• Do not place any object on the air conditioner.
• Never mix different types of batteries, or old and new batteries for the remote control.
• Do not let the air conditioner run for a long time when humidity is very high or when a door or a window has been left open.
• Stop using the remote control if there is a fluid leak in the battery. If your clothes or skin are exposed to the leaking battery fluid, wash off with clean water.
• Do not expose people, animals, or plants to the cold or hot wind from the air conditioner for extended periods of time.
• If the leaking battery fluid has been swallowed, wash off the inside of the mouth thoroughly and consult a doctor.
• Do not drink the water drained from the air conditioner.
• Do not use the product for special purposes, such as preserving foods, works of art, and etc. It is an air conditioner for consumer purposes, not a precision refrigeration system. There is risk of damage or loss of property.
• Do not recharge or disassemble the batteries.

Maintenance

• Never touch the metal parts of the air conditioner when removing the air filter.
• Use a sturdy stool or ladder when cleaning, maintaining, or repairing the air conditioner at a height.
• Never use strong cleaning agents or solvents when cleaning the air conditioner or spray water. Use a smooth cloth.

Operation

**Notes for Operation

**

Suggestion for Energy Saving

• Do not cool excessively indoors. This may be harmful for your health and may consume more electricity.
• Block sunlight with blinds or curtains while you are operating the air conditioner.
• Keep doors or windows closed tightly while you are operating the air conditioner.
• Adjust the direction of the air flow vertically or horizontally to circulate indoor air.
• Speed up the fan to cool or warm indoor air quickly, within a short period of time.
• Open windows regularly for ventilation. The indoor air quality may deteriorate if the air conditioner is used for long durations.
• Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the air flow or weaken the cooling / dehumidifying functions.
• For use in Australia, New Zealand : This air conditioner is capable of DRM1, DRM2 and DRM3 and complies with standard AS/NZS 4755.3.1.(Optional)

Parts and Functions

Indoor Unit

1. Air Filter 1 Air Intake Vents
2. Air Intake 2 Air Outlet Vents
3. Front Cover
4. On/Off Button
5. Air Deflector (Vertical Louver)
6. Air Deflector (Horizontal Vane)
7. Air Outlet

Outdoor Unit

1. Air Intake Vents
2. Air Outlet Vents

NOTE

• The number and location of operation lamps may vary according to the model of the air conditioner.
• The feature may be changed according to the type of model.

Wireless Remote Control

Inserting Batteries

If the display screen of the remote control begins to fade, replace the batteries. Insert AAA (1.5 V) batteries before using the remote control. 1 Remove the battery cover.

1. Remove the battery cover.

2. Insert the new batteries and make sure that the + and – terminals of the batteries are installed correctly.

Installing the Remote Control Holder

To protect the remote control, install the holder where there is no direct sunlight.

1. Choose a safe and easily accessible location.
2. Fix the holder by fastening 2 screws firmly with a screwdriver.

Operating Method

Point the remote control towards the signal receiver at the right side of the air conditioner to operate it.

NOTE

• The remote control may operate other electronic devices if it is directed towards them. Make sure to point the remote control towards the air conditioner signal receiver.
• For proper operation, use a soft cloth to clean the signal transmitter and receiver.
• In case of a function not provided in the product, no buzzer sound occurs from the product when a button for such function on the remote control is  pressed except for Air Flow Direction ( ), Energy Display ( ), Air Purification function ( ).

Setting the Current Time

1. Insert batteries.
   • The icon below blinks at the bottom of the display screen.

2. Press or button to select the minutes.

3. Press SET/CANCEL button to finish.

NOTE
• The On/Off Timer is available after setting the current time.

Using the °C/°F Conversion Function (Optional)

This function changes unit between °C and °F
• Press and hold button for about 5 seconds.

Operating the Air Conditioner without the Remote Control

You can use the ON/OFF button of the indoor unit to operate the air conditioner when the remote control is unavailable.
1 Open the front cover (Type2) or horizontal vane (Type1).
2 Press the ON/OFF button.

NOTE

• The stepping motor may be broken if the horizontal vane opens rapidly.
• The fan speed is set to high.
• The feature may be changed according to the type of model.
• The temperature cannot be altered when using this emergency On/Off button.
• For cooling-only models, the temperature is set to 22 °C
• For cooling & heating models, the temperature is set from 22 °C to 24 °C

Using Wireless Remote Control

You can operate the air conditioner more conveniently with the remote control.

NOTE
• * buttons may be changed according to the type of model.

NOTE
• * buttons may be changed according to the type of model.
• Press the SET/CANCEL button to operate the selected FUNC.

Restarting the Air Conditioner Automatically

When the air conditioner is turned on again after a power failure, this function restores the previous settings.
Disabling Auto Restart
1 Open the front cover (Type2) or horizontal vane (Type1).
2 Press the ON/OFF button and hold it for 6 seconds, then the unit will beep twice and the lamp will blink twice 4 times.
• To re-enable the function, press the ON/OFF button and hold it for 6 seconds. The unit will beep twice and the lamp will blink 4 times.

NOTE
• The feature may be changed according to the type of model.
• If you press and hold the ON/OFF button for 3 – 5 seconds, instead of 6 seconds, the unit will switch to the test operation. In the test operation, the unit blows out strong cooling air for 18 minutes and then returns to factory default settings.

Using the Mode Function

This function allows you to select the desired function.
Cooling Only Model

Cooling Mode
1 Turn the appliance on.
2 Press **MODE** button repeatedly to select the Cooling Mode.
• is displayed on the display screen.
3 Press or button to set the desired temperature.

Heating Mode
1 Turn the appliance on.
2 Press **MODE** button repeatedly to select the Heating Mode.
• is displayed on the display screen.
3 Press or button to set the desired temperature.

Dehumidification Mode

This mode removes excess moisture from a highly humid environment or during the rainy season, in order to prevent molding from setting in. This mode adjusts the room temperature and the fan speed automatically to maintain the optimal level of humidity.
1 Turn the appliance on.
2 Press **MODE** button repeatedly to select the Dehumidification Mode.
• is displayed on the display screen.
NOTE
• In this mode you cannot adjust the room temperature, it is adjusted automatically.
• The room temperature is not displayed on the display screen.

Fan Mode
This mode only circulates the indoor air without changing the room temperature.
1 Turn the appliance on.
2 Press **MODE** button repeatedly to select the Fan Mode.
• is displayed on the display screen.
3 Press FAN SPEED button to adjust the fan speed.

Auto Changeover Mode

Cooling & Heating Model
This mode changes the mode automatically to maintain the set temperature at ±2 °C
1 Turn the appliance on.
2 Press MODE button repeatedly to select the Auto Changeover Mode.
• **A** is displayed on the display screen.
3 Press or button to set the desired temperature.
4 Press FAN SPEED button to adjust the fan speed.

Auto Operation (Artificial Intelligence)

Cooling Only Model
This mode automatically sets the fan speed and temperature depending on the room temperature.
1 Turn the appliance on.
2 Press **MODE** button repeatedly to select the Auto Operation.
• **A**is displayed on the display screen.
3 Press or button to select the desired operation code if the temperature is higher or lower than the desired temperature.

NOTE
• In this mode, you cannot adjust the fan speed, but you can set the air deflector to rotate automatically.

Using the Jet Mode Function

Changing Room Temperature Quickly
This function allows you to cool indoor air quickly during the summer or warm it quickly during winter.
• Cooling & Heating model: The Jet Mode function is available with Cooling, Heating, and Dehumidification Mode.
• Cooling Only model: The Jet Mode function is available with Cooling, Dehumidification, Fan, Auto Operation Mode, and Air Purification function.
1 Turn the appliance on.
2 Press **MODE** button repeatedly to select the desired mode.
3 Press JET MODE button.
•**Po** is displayed on the display screen.

NOTE

• Jet Heating Mode is not available on some models.

• In Jet Cooling Mode, strong air blows out for 30 minutes.

• After 30 minutes later, setting temperature is maintaining 18 °C
  If you want to change the temperature, Press or button to set the desired temperature.

• In Jet Heating Mode, strong air blows out for 30 minutes.

• After 30 minutes later, setting temperature is maintaining 30 °C
  If you want to change the temperature, Press or button to set the desired temperature.

• This function may operate differently from the remote control display.

Using the Fan Speed Function Adjusting the Fan Speed

• Press FAN SPEED button repeatedly to adjust the fan speed.

NOTE
• The fan speed of Natural Wind adjusts automatically.

• The fan speed icons are displayed on some indoor units.

• Indoor unit display is displayed only 5 seconds and returns to the set temperature on some models.

Using the Air Flow Direction Function

This function adjusts the direction of the airflow vertically (horizontally).
• Press ( ) button repeatedly and select the desired direction.
− Select  ( ) to adjust the direction of the airflow automatically.
NOTE
• Adjusting the airflow direction horizontally may not be supported, depending on the model.
• Adjusting the air deflector arbitrarily may cause product failure.
• If you restart the air conditioner, it starts to operate with the previously set direction of airflow, so the air deflector may not match the icon displayed on the remote control. When this occurs, press or  button to adjust the direction of the airflow again.
• This function may operate differently from the remote control display.

Setting the On/Off Timer

This function sets the air conditioner to turn on/off automatically at desired time.

Setting the On Timer
1 Press button repeatedly.
• The icon below blinks at the bottom of the display screen.
2 Press or button to select the minutes.
3 Press SET/CANCEL button to finish.
• After setting the timer, current time and **ON** icon are displayed on the display screen indicating that the desired time is set.

Canceling the On Timer
1 Press button repeatedly.
• The icon below blinks at the bottom of the display screen.

2 Press SET/CANCEL button to cancel the setting.

Setting the Off Timer
1 Press button repeatedly.
• The icon below blinks at the bottom of the display screen.

2 Press or button to select the minutes.
3 Press SET/CANCEL button to finish.
• After setting the timer, the current time and **OFF** icon are displayed on the display screen indicating that the desired time is set.

NOTE
• This function is disabled when you set Simple Timer.
Canceling the Off Timer
1 Press button repeatedly.
• The icon below blinks at the bottom of the display screen.

2 Press SET/CANCEL button to cancel the setting.
Canceling the Timer Setting
• Press button to cancel all timer settings.

Using the Sleep Function (Optional)

This function turns off the air conditioner automatically when you go to sleep.
1 Turn the appliance on.
2 Press button repeatedly.
• The icon below blinks at the bottom of the display screen.
3 Press or button to select the hour (up to 7 hours).
4 Press SET/CANCEL button to finish.
• is displayed on the display screen.
NOTE
• **IH** is displayed on some indoor units.
• Indoor unit display is displayed from 1H to 7H which is displayed only 5 seconds and then return to the setting temperature.
• In the Cooling and Dehumidification Mode, the temperature increases by 1 °C after 30 minutes and add 1 °C after another 30 minutes for a more comfortable sleep.
• The temperature increases up to 2 °C from the preset temperature.
• Although the remark for fan speed on the display screen may be changed, the fan speed is adjusted automatically.

Using the Simple Timer Function (Optional)

This function turns off the air conditioner automatically when you go to sleep.
1 Turn the appliance on.
2 Press button repeatedly.
• The icon below blinks at the bottom of the display screen.

3 Press or button to select the hour (up to 7 hours).
4 Press SET/CANCEL button to finish.
•**S**is displayed on the display screen.
NOTE
• This function is disabled when you set Off Timer.

Using the Energy Display Function (Optional)

This function displays the amount of electricity generated on the indoor display as the product operates.
Display the Current Energy Usage
1 Turn the appliance on.
2 Press button and hold it about 3 seconds.
• The instantaneous power consumption ( ) is displayed for a while on some indoor units.

Display the Cumulative Energy Usage (Optional)
1 Turn the appliance on.
2 Press button and hold it about 3 seconds twice.
• The cumulative power consumption ( ) is displayed for a while on some indoor units.
NOTE
• It is not displayed on the wireless remote control.
• kW refers to instantaneous power consumption.
• kWh refers to cumulative power consumption.
• If it is more than 99 kWh, which is the range of expression, maintain it as 99 kWh.
• Power off resets its value.
• Display wattage under 10 kW(h) with 0.1 kW(h) unit, and display one over 10 kW(h) with 1 kW(h) unit.
• The actual power may differ from the power displayed.

Using the Light Off Function (Optional)

Display Screen Brightness
You can set the brightness of the indoor unit display screen.
• Press LIGHT OFF button.
NOTE
• Turn on/off the Display screen.

Using the Comfort Air Function (Optional)

Comfort Vane Operation
This function conveniently sets the vane to a preset position to deflect the supply air away from blowing directly onto the occupants in the room.
1 Turn the appliance on.
2 Press **COMFORT AIR** button repeatedly and select the desired direction.
is displayed on the display screen.

NOTE
• is displayed on some indoor units.
• This function is disabled when you press the MODE or JET MODE button.
• This function is disabled and auto swing of vertical direction is set up when you press the button.
• When this function is off, the horizontal vane operates automatically depending on the set mode.

Using the Energy Saving Function (Optional)

This function minimizes power consumption during Cooling and increases the set temperature to the optimal level for a more comfortable environment. The temperature automatically settles at 22 °C if room ambient temperature is below 22 °C The temperature remains constant if it is above 22 °C
1 Turn the appliance on.
2 Press MODE button repeatedly to select the Cooling Mode.
3 Press ENERGY SAVING button.
• **e** is displayed on the display screen.

Using the Energy Control Function (Optional)

1 Turn the appliance on.
2 Press ENERGY CTRL button.
• Press ENERGY CTRL button repeatedly to select each step.
NOTE

• 1step : The power Input is decreased by 20 % compared to rated power input.
  − **80** is displayed on the display screen.

• 2 step : The power Input is decreased by 40 % compared to rated power input.
  − **60**is displayed on the display screen.

• 3 step (Optional) : The power Input is decreased by 60 % compared to rated power input.
  −**40**is displayed on the display screen.

• (1 step), (2 step) is displayed on some indoor units.

• This function is available with Cooling Mode.

• Capacity may decrease when Energy Control mode is selected.

• Desired temperature is displayed about 5 seconds if you press FAN SPEED, or button.

• Room temperature is displayed about 5 seconds if you press ROOM TEMP button.

Using Special Functions

1 Turn the appliance on.
2 Press FUNC button repeatedly to select the desired function.
3 Press SET/CANCEL button to finish.

NOTE
• Some functions may not be supported, depending on the model.
• Some functions may operate differently from the remote control display.

Canceling Special Functions

1 Press FUNC button repeatedly to select the desired function.
2 Press SET/CANCEL button to cancel the function.
Using the Air Purification Function
These functions supply clean and fresh air by ion particles and the filter.

NOTE

• You can use this function without turning the air conditioner on.
• Both the plasma lamp and the cooling lamp light up while Smoke Away/Plasma is in operation on some models.
• Do not touch ionizer during operation.
• This function may operate differently from the remote control display.

Using the Silent Function

This function prevents potential claims by neighbors, reducing noise from outdoor units.
• is displayed on the display screen.
NOTE
• This function is disabled when you press MODE or ENERGY CTRL or JET MODE button.
• This function is available with Cooling, Heating, Auto Changeover, Auto Operation Mode.

Using the Ion Care Function
This function keeps your skin moisturized by generating ion clusters which is absorbed into the surface of skin.
• is displayed on the display screen about 3 seconds.
NOTE
• This function is available with Cooling, Fan Mode and Air Purification function.

Using the Jet Dry Function
This function maximizes the performance of dehumidification.
• ,**Po** are displayed on the display screen.
NOTE
• This function is available with Cooling, Dehumidification, Auto Operation, Fan Mode and Air Purification function.
• This function is not available with Sleep function.
• This function is disabled when you press MODE button.

Using the Low Heating Function
This function operates the heating system to maintain a minimum room temperature and prevent objects in the room from freezing where there is no permanent resident, such as a vacation.
•**LH**, LH is displayed on the display screen.
NOTE
• This function is available with Heating Mode.
• During LH operation, when you press buttons such as , , MODE, FAN SPEED, andthen return to Heating Mode, 30 °C high speed.
• If JET MODE button is pressed during LH operation, this function is disabled and Power Heating Mode is operated immediately. (only for power heating model)
• In case an error occurred, operation can be interrupted for the protection of the product.
• COMFORT AIR and button cannot be used while the LH function is in operation.

Using the Mosquito Away Function
This function fans away mosquitos by generating a high-frequency wave.
• is displayed on the display screen.
NOTE
• You can use this function without turning the air conditioner on.

Using the Auto Clean Function
In the Cooling and Dehumidification Mode, moisture is generated inside the indoor unit. This function removes such moisture.
• is displayed on the display screen.
NOTE
• Some functions cannot be used while the Auto Clean function is in operation.
• If you turn off the power, the fan operates for 30 minutes and cleans the inside of the indoor unit.

Using the Comfort Sleep Function
This function operates the air conditioner automatically to make the comfortable sleep environment.
• , SL are displayed on the display screen.
NOTE
• This function is available with Cooling Mode.
• The vane stops swing and sets indirect airflow angle, after 30 minutes from start even though the room temperature doesn’t decrease to optimal temperature to sleep.
• It is possible that a comfortable sleep environment is different according to the people.

SMART FUNCTIONS

Using Smart ThinQ Application

Installing Smart ThinQ
Search for the LG Smart ThinQ application from the Google Play Store or Apple App Store on a smart phone. Follow instructions to download and install the application.
Product Registration
1 Run the LG Smart ThinQ application on a smart phone.
2 Create an account and sign in.
3 Select Register.
4 Select Air conditioner.
5 Follow the instruction on the smart phone.
Wi-Fi Function
• For appliances with the logo Communicate with the appliance from a smart phone using the convenient smart features. Using the Application
1 Select the appliance in the application and connect it to a Wi-Fi network.
2 Select the menu on the upper right side to access settings and features.

Firmware Update
Keep the appliance performance updated.
Smart Diagnosis™
If you use the Smart Diagnosis function, you will be provided with the useful information such as a correct way of using the appliance based on the pattern of use.
Settings
Allows you to set various options on the appliance and in the application.
NOTE

• To verify the Wi-Fi connection, check that Wi-Fi icon on the control panel is lit.
• LG Smart ThinQ is not responsible for any network connection problems or any faults, malfunctions, or errors caused by network connection.
• The machine supports 2.4 GHz Wi-Fi networks only.
• If the security protocol of the router is set to WEP, you may fail to set up the network. Please change it to other security protocols (WPA2 is recommended) and register the product again.
• For the router’s SSID (the name of the wireless router that appears when searching for Wi-Fi), please use only English alphabets and numbers. Other characters may not be supported.
• If the appliance is having trouble connecting to the Wi-Fi network, it may be too far from the router. Purchase a Wi-Fi repeater (range extender) to improve the Wi-Fi signal strength.
• The Wi-Fi connection may not connect or may be interrupted because of the home network environment.
• The network connection may not work properly depending on the internet service provider.
• The surrounding wireless environment can make the wireless network service run slowly.
• The application is subject to change for appliance improvement purposes without notice to users.
• Functions may vary by model.

RF Radiation Exposure Statement
• This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
Open Source Software Notice Information
To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.

Smart Diagnosis™ Using a Smart Phone
• For appliances with the  logo Use this function if you need an accurate diagnosis by an LG Electronics customer information centre when the appliance malfunctions or fails.
Smart Diagnosis™ can not be activated unless the appliance is connected to power. If the appliance is unable to turn on, then troubleshooting must be done  without using Smart Diagnosis™.
1 Open the LG Smart ThinQ application on the smart phone.
2 Select the air conditioner in dashboard.
3 Press Start Smart Diagnosis button.
4 Follow the instructions on the smart phone.
NOTE
• The Smart Diagnosis™ function depends on the local call quality.
• If the Smart Diagnosis™ data transfer is poor due to poor call quality, you may not receive the best Smart Diagnosis™ service.
• Be sure to keep ambient noise to a minimum or the phone may not correctly receive the buzzer beeps from the indoor unit.

MAINTENANCE

WARNING
• Before cleaning or performing maintenance, disconnect the power supply and wait until the fan stops.
If the air conditioner will not be used for an extended period of time, dry the air conditioner to maintain it in best condition. Clean the product regularly to maintain optimal performance and to prevent possible breakdown.
• Dry the air conditioner in Fan mode for 3 to 4 hours and disconnect the power. There may be internal damage if moisture is left in its components.
• Before using the air conditioner again, dry the inner components of the air conditioner in Fan mode for 3 to 4 hours. This will help to remove the odor generated from moisture.

• The feature may be changed according to the type of model.

NOTE
• Never use water that is higher than 40 °C when you clean the filters. It may cause deformation or discoloration.
• Never use volatile substances when you clean the filters. They may damage the surface of the product.
• Do not wash the 3M filter with water, because the filter can be damaged (Optional).
• Do not wash the Triple filter with water, because the filter can be damaged (Optional).

Clean the Air Filter

Clean the air filters once every 2 weeks, or more, if necessary.
NOTE
• The air filter can be broken when it is bended.
• When the air filter is not assembled correctly, dust and other substances come into the indoor unit.
Type1
If you look at the indoor unit from above it, can assemble the top filter easily.
1 Turn off the power and unplug the power cord.
2 Hold the knobs of the air filter, lift it up slightly.

3 Remove it from the indoor unit.

4 Clean the filter with a vacuum cleaner or with lukewarm water with neutral detergent.
5 Dry the filter in the shade.
6 Insert the hooks of the air filter into the front cover.

7 Push down hooks to assemble the air filter.

8 Check the side of the front cover for correct assembly of the air filter.
Type2
1 Turn off the power and unplug the power cord.
2 Open the front cover.
• Lift up both sides of the cover slightly.
3 Hold the knobs of the air filters, pull them down slightly and remove them from the indoor unit.

4 Clean the filters with a vacuum cleaner or with lukewarm water with neutral detergent.
5 Dry the filters in the shade.
6 Insert the hooks of the air filters into the front cover.

7 Check the side of the front cover for correct assembly of the air filters.

Clean the 3M and Triple Filter (Optional)

1 Turn off the power and unplug the power cord.
2 Remove the air filters from the indoor unit.
3 Remove the 3M and Triple filters from the indoor unit.
Type1

Type2

4 Clean the filters with a vacuum cleaner.
5 Insert the 3M and Triple filters.
Type1

Type2

6 Assemble the air filters.
7 Check the side of the front cover for the correct assembly of the air filters.
NOTE
• The feature and location of 3M and Triple filter may vary according to the type of model.

TROUBLESHOOTING

Self-diagnosis Function
This product has a built-in self-diagnosis function. If an error occurs, the lamp of the indoor unit will blink in 2 second intervals. If this occurs, contact your local dealer or service center.
Before Calling for Service
Please check the following before you contact the service center. If the problem persists, contact your local service center.

LG Wall-Mounted Air Conditioner Instructions and Remote Button Help

VIDEO

Are the inside walls of the unit plastic or styrofoam (when you look through the vent)?

My 2021 LG 10,000 BTU has no styrofoam inside. There are some open cell foam strips on the chassis walls to dampen vibration. I don’t think they will be an issue.

Does it have those sliding panels at the side ?

It does but beware, THEY ARE SHORT! Max window width for this air conditioner would be about 31 inches.

Does anybody get a loud rattling noise in the grill? The units vibrations are transferred to the front and its very loud rattling?

My 2021 10K BTU had zero rattles. The only thing I hear is a very steady PLEASING white noise whoosh of the fan.
I can barely hear the compressor when it cycles.

Minimum window width?

I believe the specs say 21″. Mine is 20 7/8″ and it fits just fine. The unit is only about 18″ wide, but there are sleeves on each side that adjust to ensure a tight seal between the machine and the window. The extra space required is to accommodate them.

Which is width, 26″ or 28″?

Width is 26″
Height is 17″.6875
Depth is 28″

Can this be installed through the wall instead of in a window?

Absolutely, I installed mine this past Saturday, works like a charm.

is there an energy saving button?

Yes there is a button.

Does it have auto restart if power goes off?

Yes

What mounting bracket do I use for l g15,000 btu air conditioner?

The brackets it comes with work just fine

what is the wattage?

Since the specs show 7.7 amps for this air conditioner, then the watts should be about 770.

NOTE
• Some functions may not be supported, depending on the model.

Memo

lg-t09awn-premium-25kw-reverse-cycle-split-system-inverter-air-conditioner- user-manual [pdf]LG Wall-Mounted Air Conditioner Instructions and Remote Button Help.pptx

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>