LEEDARSON Motion sensor Pet Immunity User Guide

: June 7, 2024
: LEEDARSON

Table of Contents

LEEDARSON Motion Sensor Pet Immunity Quick Start Guide
Documents / Resources
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LEEDARSON Motion Sensor Pet Immunity Quick Start Guide

LEEDARSON

Z-Wave™
7CA-SS-VE-C0

1. Product Introduction

The Motion Sensor lets you know when movement is detected in a certain area and can trigger different actions in response to that movement (or lack of movement). It supports the pet immunity up to 80 lbs. This sensor integrated Z-Wave communication module to connect with Z-Wave gateway, and this device can be adapted to EU(868.42Mhz) or US(908.42MHz).

If you want your Motion Sensor to be a security device that use secure/encrypted message to communicate in a Z-Wave network, then a security enabled Z-Wave controller is needed.

The motion sensor can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.

2. Product Appearance

Product appearance and function overview.

Function Overview

Button:

Short press reset button into learning mode, then the sensor can inclusion or exclusion from the Z-Wave network.
Hold the key for 5s to reset the sensor, after reset, Sensor will send “Device_Reset_Locally” to the main controller and exclude from the Z-Wave network when the Button is released, this procedure will reset the Sensor to factory default.
Short press button for 3 times then the sensor sending wake up notification to gateway, and LED will fast blink when sending data, send over then the LED turn off..

Specification|
---|---
Detection angle| 80 degrees
Detection distance| 8 meters / 26.25 feet
Pet immune| 80 lbs (36 kgs)
Mounting height| 6.23 ft. to 7.55 ft.
(1.9m to 2.3m)
Light sensor| 20 lux for day/night(bright/dark)
Protocol| Z-Wave
Frequency| 908.42MHz (US)
868.42MHz(EU)
Power source| Battery-powered
Battery type| CR123A X 1
Battery life| 3 years
Anti-Tamper| YES
Low power alarm| YES
Certifications| CE/FCC/Z-Wave

3. Features/Capabilities:

Supports pet immunity up to 80 lbs (36 kgs)
Use PIR & Fresnel lens technology
Easy installation with bracket
Low battery alarm
Equipped with an anti-tamper switch that reports any tampering

4. Installation Position and Notes

Installation position should be chosen at the area which the bass-by will be across, try to make the bass-by in the detection area as below.
Side view

Top view
Do avoid installation near air-conditioner, electric fans, refrigerators, ovens or other places where temperature easy change.
In order not to affect the detecting result, there should be no object in front of the produces lens.
Building (such as the wall) will shorten the distance of wireless communication.
This device can be mounted on the wall only, it cannot be installed on the ceiling.

5. Product Installation

Adding the device as accessories, install it according to the diagram below:

Choose the installation location on the wall, fix the bracket by screw or 3M adhesion tape on the wall.
Take off the bracket in the back, and draw out the battery insulation sheet, then assembly the bracket.
Assembly the main body to the bracket.

6. Product Usage

Function of Action Button:

6.1 All functions of each trigger:

Function Of Action

Function Of Action Table

Function Of Action Table Continued

6.2 Caution:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Hereby, Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU

6.3 Low voltage alarm to remind changing battery.

This product has low voltage detection reminder, when the battery voltage is in low status, the detector will give out low battery signal to controller.

7. Attention

If need to clean the sensor, please use a soft cloth with a little alcohol to wipe it after you cut off the power.
This product is just for indoor use.
Replace the battery timely on low battery warning to ensure the detector works properly. Please remove the battery and safe keeping, if you don’t use this product for a long time.
This device can be mounted on the wall only, it cannot be installed on the ceiling.
The reference range template of PIR detection is tested at the indoor temperature (the range is 20°C~25°C), the target of the test is 77kg±10kg weight and 1.71m± 0.3m height, the target of the test across movement speed is 4m/s±0.15m/s.
In order to prevent the PIR sensor’s abnormal fault, please don’t mounting and operating sensor in the bellow conditions,
Firstly, product mounting should prevent installed in the air flow environment such as in front of the door, window, heater, air conditioner and so on.
Secondly, the PIR detection area should not be shielded by other screen.
Thirdly, if the operating temperature range is out of the defined range of product specification may result in some product faults, which is not in the technique commitment of manufacturer.
Fourthly, this product has mot pet immunity function, so when some animals go through in front of the product may trigger PIR function reported.

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Disposal