CA-605T Smart Ultrasonic Humidifier Clean Air Optima User Manual

June 3, 2024
Clean Air Optima

CA-605T Smart Ultrasonic Humidifier Clean Air Optima

Thank you for purchasing the Clean Air Optima® Ultrasonic Humidifier CA-605T Smart.
We wish you many years of healthy indoor air with this efficient and effective product.
These instructions describe the safety precautions to be observed during operation. They are meant to prevent injuries and to avoid damaging the device.

Description of the device

The device consists of the following main components:CA-605T Smart
Ultrasonic Humidifier Clean Air Optima fig 1

  1. Top panel
  2. Water filter
  3. Handle
  4. Water tank
  5. Float
  6. Panel
  7. Air outlet
  8. Aroma box
  9. Front panel
  10. Tranducer
  11. Power Cord
  12. Sensor
  13. Mist nozzle

Safety warnings
This device may only be used in accordance with these safety instructions. Take the following steps to minimize the risk of personal injury caused by for example electric shocks or fire.

  1. Only for indoor use. Do not use or store outdoors.

  2. Use proper voltage: AC 220V – 240V, 50/60Hz.

  3. The inner ultrasonic transducer is highly sensitive. Do not touch it with bare fingers or scrape it with metal tools, or it will reduce mist output. When cleaning this area please use a small cleaning brush, cotton swab or tooth brush. Do not use hot water as it may damage the misting parts.

  4. The device is not intended to be used by children or persons with reduced physical-, sensory- or mental capabilities, unless they are supervised by a person responsible for their safety.

  5. Children should be kept away unless continuously supervised.

  6. To safely use the device, put it in a steady, horizontal position. Do not move while using.

  7. To prevent interference and damage to other electronic devices, this machine should
    be placed at least 1 meter away from a computer, television, radio or other electronic equipment.

  8. Do not use the device when there is visible damage on the electrical cord or on the device itself. Do not repair the device yourself in case of damage. Never pull the device by its cord. If the power cord is damaged, then it must be replaced by an authorized service person to prevent electric shock or fire.

  9. Repairs may only be performed by authorized service personal. Do not try to repair the device yourself to prevent electric shock or fire.

  10. Always remove the plug from the socket when the device is not being used or when you clean internal or external parts of it.

  11. Remove the water from the tank before moving the device.

  12. Only use power cords provided.

  13. Do not use the device in rooms where inflammable liquids or gases are stored, close to heat sources or in particularly humid rooms like the bathroom, shower or swimming pool.

  14. To prevent malfunctions, never insert strange objects into the device.

  15. Never dissemble or replace the device’s inner parts.

  16. Do not place the device in direct sunlight, to avoid that the device discolours.

  17. Never immerse the unit in water or other liquids.

  18. Do not touch the power cord with wet hands.

  19. Clean and dry the device before storage (including the removal of all water from the inside of the device). Store the machine in a cool and dry place outside the reach of children.

  20. Do not clean the water sink when the water is still hot.

  21. Use, maintain and clean the device as described in this manual.

Operating instructions

Before getting started, remove the Clean Air Optima® CA-605T Smart from its box and allow it to become accustomed to the room temperature for at least 30 minutes especially if the machine is cold from the outside air. Place the device on a solid, level and front water-insensitive surface, approx. 60 cm from the floor and at least 20 cm from the wall.
The CA-605T Smart is designed to operate at temperatures between 5 -40 ºC and relative humidity of less than 75%.
To get started, remove the top panel from the device. Grab the water tank by the handle and remove the water tank.CA-605T Smart Ultrasonic Humidifier
Clean Air Optima fig 3

Then place the water tank under the faucet for filling, grasping it from the handle from the water tank. Fill the tank with tap water (or other clean water source with water temperature under 40ºC). Ensure that the basin is clean and then carefully place the water tank back in the lower body.
Top filling: The water tank can also be refilled with a watering can.
Directly from the top of the humidifier.
Wait a few seconds until the water tank starts to release water into the basin.
Plug the power plug into a suitable power outlet, a signal sounds to indicate that your device is in standby mode.

Power Button
Press the Power Button to activate the humidifier. The machine is now operating in manual mode. It will release cool mist on a constant basis with the mist intensity level automatically set to medium.
Manual Button
The Manual Button changes the mist level (low, medium, high, automatic). There are 3 levels of mist output available. If the device is in automatic mode, it will automatically adjust the mist intensity.
Humidity Button
Pressing the Humidity Button, you can select the desired humidity level by pressing this button repeatedly until the required humidity level is displayed (from 30% to 75% in increments of 5%). Once you select your desired humidity level, simply stop pressing the button and your humidity level will be set. The display will blink 3 times and then the setting is saved. When the humidity level in the room reaches the set humidity level, the machine will go into automatic sleep state and stop producing mist. When the room’s actual humidity level drops below your set humidity level, then the machine will start producing mist again.
Negative Ion Button
Pressing the Negative Ion Button will activate the negative ion generator with a total capacity of > 3.000.000 negative ions / cm³ that are spread through out the entire room and thereby neutralize pollutants and smells. Negative ions attach onto dust particles, microorganisms and other unwanted particles in the air and connect them to each other. This way, the particles become heavier than air and fall onto the ground so that you can no longer breathe them in. Press the button again to turn off the Negative Ion function. Negative ions are most found in the forest, mountains and by the sea. Negative ions ensures fresh and healthy air.
Timer Button
Pressing the Timer Button sets the timer. The timer function determines how many hours the humidifier will operate. You can set the timer simply by pressing it once for each hour that you would like to run the device. The timer can be set from 1 hour to 12 hours. As time passes, the time value decreases until it goes to 00:00 and the device shuts off. To turn off the timer function, press and hold the Timer Button for 3 seconds.
Sleep Mode
When the sleep mode is activated, the display will turn off. Only the sleep mode light is on. The mist output from the humidifier will be operating in “low level“. Press the button twice for activate and press the button twice for turning off sleep mode.
WiFi Mode
Press the button 3 seconds to open the WiFi network.
Press the button for 3 seconds to reset the WiFi network, when the device is connected to iPhone, iPad or android device.
UV-Light Button
Pressing the UV-Light Button, the device starts the UV Sterilization function, which kills the bacteria in the mist output airflow, bevor the mist enters into the room. The UV-Light icon is shown on the LED display. Press the button again to stop the UV-light function.
Water tank empty indicator light
Automatic shutdown when water tank is empty. Should the water tank be empty, a threefold acoustic signal sounds. The corresponding symbol lights up in the display while the remaining indicators go out. The device will automatically stop humidifying. In this case, turn off the device with the ON/ OFF button. Let the device cool down before pouring any more water in the tank.
Ensure that the water tank is always completely refilled.
Display
If the device is switched on, the display will automatically dim after 15 seconds.
Touch a button first to activate the display and then touch the button again to activate the function.

Operation with Clean Air Optima® App

CA-605T Smart Ultrasonic Humidifier Clean Air Optima fig
4

Connectivity
Compatibility with smartphone and tablet: iPhone, iPad and Android devices
Device connets via WiFi with App: CleanAirOptima
About the Clean Air Optima® App

Set up WiFi connection

  1. Download and install the Clean Air Optima® App in
    the App Store or Google Play Store.

  2. Make an account and log in.

  3. Plug the device into the power socket and switch it on. The WiFi indicator will blink.

  4. Make sure that your smartphone or tablet is successfully connected to your WiFi network.

  5. Open the Clean Air Optima® App and click on ‘Add device’ . Your device is listed and you can select it. If not choose ‘Auto Scan’. Follow the on-screen instructions to connect the device to your network.

  6. Choose to add the Clean Air Optima® device on the App, follow the instructions in the App.

  7. When the device is paired, the WiFi indicator light stays on constantly.

  8. After the configuration is successful, you can use the Clean Air Optima® App to operate the device.

Note:

  • If your default network has changed, reset the WiFi connection, follow step 3 to 8 in the
    ‘Set up WiFi connection’ section.

  • If you want to pair multiple devices to your smartphone or tablet, you have to do this one after the other.

  • Make sure that the distance between your smartphone or tablet and the device is less than 5 meters and there are no obstacles. Also make sure you are in the same room as the device.

Reset the WiFi function
Reset the WiFi by pressing the ‘Sleep Mode’ button for 3 seconds, the indicator light of the WiFi will blink rapidly.

Connect devices to multiple phones

Note: First the other person needs to install the Clean Air Optima® App on his/her phone and create a new account.
Share the device with limited access:
You can choose to share 1 device with several persons.
This person will then have access, but will not be able to manage all the settings.
Follow the instructions below to share the device with several persons:

  1. Go to the relevant device.
  2. Go to the pencil or three dots in the top right.
  3. Select ‘Share device.‘
  4. Choose ‘Add sharing‘.
  5. Choose the sharing method e.g. via email, whatsapp, sms etc. and continue.
  6. The device will automatically appear in the Clean Air Optima® App with the other account.

Share device with full access
You can add a person or several persons to your home management.
That person will then have access to all your devices that are already linked and has full rights and permissions. You will always remain the main administrator.
Follow the instructions below to add someone to your home management:

  1. Open the Clean Air Optima® App and go to ‘Me’.
  2. Then choose ‘Home Management’.
  3. Choose ‘Create a home’.‘
  4. Select the relevant ‘Home’ and ‘Add member‘.
  5. Choose the sharing method e.g. via email, whatsapp, sms etc. and continue.
  6. The corresponding ‘Home‘ will automatically appear in the Clean Air Optima® App of the person with whom you have shared your ‘Home‘.
  7. On the other account: Go to the home screen from the Clean Air Optima® App. Go to the top left and select the ‘Home‘.

Preparation Clean Air Optima® Water Filter W-02

The Water Filter W-02 reduces the limescale in the water and the undesirable emission of limescale particles into the room surroundings. Effective for one to three months, depending on the water hardness. Install a new Water Filter W-02 every 2 to 3 months, depending on the water hardness.

  1. Unscrew the Water Filter W-02 from the bottom of the water tank.
  2. Rinse the Water Filter W-02 for 2 minutes under cold running tap water.CA-605T Smart Ultrasonic Humidifier Clean Air Optima fig 5
  3. Screw the Water Filter W-02 to the bottom of the water tank.

Dispose of the saturated Water Filter W-02 with your regular household waste.
The Water Filter W-02 should not be used longer than specified.
You can order the Water Filter W-02 in our online store at www.cleanairoptima.com.

Replacing the Clean Air Optima® Water Filter W-02
The Clean Air Optima CA-605T Smart is equipped with a filter lifespan surveillance mecha-nism that signals that the water filter have to be replaced after 400 working hours. To show that the

Water Filter W-02 need to be replaced, the humidifier emits a double zero indicator light. Reset the timer for the water filter by pressing and holding the power button for about 3 seconds. If the indicator light goes out, the timer has been successfully reset.

Aromatherapy

Activating the aroma function:

  • Remove the aroma tray from the bracket by pressing the aroma box.
  • Pour 5- 10 drops of Clean Air Optima® essential oil onto the sponge.
  • Put the aroma tray back into the bracket.
  • When you turn on your air humidifier, the aroma function will be activated.
  • If you want to deactivate the aroma function, or should the device not be in use for extended periods of time, remove the aroma sponge from the compartment and wash it with a little of mild soap water. Let it dry completely before placing it back in the aroma compartment. Basically the aroma sponge is reusable.CA-605T Smart Ultrasonic Humidifier Clean Air Optima fig 6

Important
In order to reach the best results and to enjoy your ultrasonic air humidifier as much as possible, we advise to read carefully the following instructions regarding the use of essential oils in the ultrasonic air humidifier CA-605T Smart.

Use of essential oils in the CA-605T Smart
Use our high quality essential oils and enjoy your personal aromatherapy! A scent sensation at its highest level!
You can find high quality essential oils with many different scents in our assortment. They perfectly fit to the ultrasonic air humidifier CA-605T Smart and have been specially developed for the use with this ultrasonic humidifier:

You can order the Essential Oils in our online store at www.cleanairoptima.com.

Warning
The use of other essential oils not made for this air humidifier or other additives (for example: fragrances and water purification products) can damage the air humidifier and must NOT be used! Never put other pure essential oils or other additives into the water tank resp. the waterbasin! Even a small quantity can damage the plastic and cause cracks.
The material is not made for the use of additives. One drop is enough to damage the water tank/ waterbasin and disable the device. Devices that are damaged through additives are excluded from the guarantee.

Cleaning and maintenance

You can ensure that your Clean Air Optima® CA-605T Smart humidifier will provide years of trouble-free operation by following a few simple maintenance procedures. If your water is hard and contains high concentrations of calcium and other minerals, over time white dust (lime) will start to settle on the various surfaces in the room. A white deposit (lime scale) will also form in the water basin, on the transducer and on the interior of the water tank. Lime deposits will impair the proper functioning of the transducer and the efficient hygienic humidification of the unit.
We recommend the following:

  1. Clean the transducer and the water basin once a week if you use the appliance daily with Clean Air Optima® Cleaner & Descaler.
  2. As soon as the water tank needs refilling, pour out any remaining water and fill it with fresh water.
  3. Clean the entire device and keep all parts completely dry when the device is not in use.CA-605T Smart Ultrasonic Humidifier Clean Air Optima fig 8

Specially developed for Clean Air Optima® humidifiers:

  • Not aggressive
  • Protects plastic and ceramic materials of the humidifier
  • Odour neutral
  • Cleans & descales quickly and thoroughly
  • Biodegradable

You can order the Clean Air Optima® Cleaner & Descaler from our online shop at www.cleanairoptima.com.

Cleaning the transducer and water basin
Unplug the device.
During cleaning and descaling, the device must not be used.
Remove any splashes of Clean Air Optima® Cleaner & Descaler from work surfaces or the out-side of the device with a soft, damp cloth.CA-605T Smart
Ultrasonic Humidifier Clean Air Optima fig 9

  1. Pour two capfuls of Clean Air Optima® Cleaner & Descaler into the water basin (one onto the surface of the transducer and one in the water basin) and leave for between two and five minutes.

  2. Carefully remove the mineral (lime) layer from the surface of the transducer with a small brush, cotton swab or toothbrush.
    Caution: never use sharp or hard objects to clean the transducer.

  3. Then add water up to the rim of the water basin and leave for a minimum of 30 and a maxi-mum of 60 minutes.

  4. Rinse the transducer and water basin thoroughly with water.

  5. If there are still traces of limescale visible, we recommend that you repeat the cleaning and descaling process.

  6. Clean the inside of the water tank with a mild detergent and rinse with clean water.

After cleaning and descaling, your device is hygienically clean, free of limescale, free of bacteria, free of viruses and immediately ready for use again.
Please note:
For cleaning and descaling, the device must be turned off/unplugged, so that no acid is re-leased into the air via aerosols through ultrasonic misting.

Troubleshooting

The following is a troubling shooting guide to help you solve any issues that you may have using the Clean Air Optima® Ultrasonic Humidifier CA-605T Smart.

Problem Possible Cause Solution

No mist diffused.

| Power plug not plugged in.

ON / OFF button not activated. Empty water tank.

Not enough water in tank.

| Plug in device.

Press ON / OFF button. Fill tank with water.

Refill tank with water.

The mist has a strange odour.

| A new device.

It either has dirty water or the water has been stagnant too

long.

| Remove the water tank, unscrew the lid and let it air out in a cool area for 12 hours.

Clean the water tank and refill

with clean water.

The volume of spray mist is too low.

| Too much mineral scale in the water basin and on the transducer.

Water is too dirty or water was

kept too long in the tank.

| Clean the water basin and the transducer with:

Clean Air Optima® Cleaner &

Descaler.

Clean the water tank and refill

with clean water.

Device is noisy.

| Water tank not positioned correctly.

Not enough water in the water tank.

Device is on an unstable

surface.

| Correctly position water tank on the base.

Refill water in the water tank.

Place device on solid and even

ground.

Spray mist is coming out of the area around the mist nozzle.

|

There are gaps between the housing around the nozzle and the top of the water tank/ top panel.

| Remove the top panel from the water tank and clean with a damp cloth. Reattach to the water tank.

Check whether the top panel is properly connected to the panel.

Operation with Clean Air Optima® App does not work.

|

Smartphone or tablet is not connected to WiFi network.

The device has no connection to the network.

| Switch off the device and re- set the WiFi on the device by pressing the Sleep mode but- ton for 3 seconds, the indicator light of the WiFi will blink. Than follow step 3 to 8 from chapter

Operation with Clean Air Optima®

App.

If your water is very hard (containing abnormally high levels of minerals) the humidifier may produce white dust. This is not a malfunction. The solution would be to replace the Water Filter W-02 more often or use softer water, like distilled water. Or we can recommend Clean Air Optima Air Washers, more info in our online store www.cleanairoptima.com.
WARNING
If the above recommended solutions do not work, please contact Clean Air Optima technical support at the telephone number for your region. Do not attempt to disassemble, reassemble, or repair the device as this may void the warranty.

Specifications

  • Model: CA-605T Smart
  • For rooms up to: 65m² / 140m³ / 590ft²
  • Rated voltage: 220V – 240V, 50/60Hz
  • Rated power: 30W
  • Capacity air humidification: Min. 120 ml/h – Max. 480 ml/h
  • Active oxygen: <0.05 ppm
  • Sound level Silent fan: < 25dB(A)
  • Dimensions: 210 x 215 x 290 mm
  • Weight: 2,8 kg
  • Water tank: 3,8 L
  • Colour: Titanium/ gray with transparent water tank
  • Complies with EU regulations: CE / WEEE / RoHS

Ask your retailer or your municipality for updated information regarding the disposal of the packaging and of the device.

Service

Warranty Certificate for the Clean Air Optima® Ultrasonic Humidifier CA- 605T Smart.
Date of purchase:
Customers name:
Address:
Telephone:
Email:
Seller’s name:
Address:

  1. Please fill in completely this Warranty Certificate. Send it with the invoice and the unit, postage pre-paid and using the original packing box, to your distributor. Make sure to include the appropriate return postage for the package.
  2. Please enclose a short description of the damage, fault or malfunction, and the circumstances under which these problems arose.

The Clean Air Optima® Ultrasonic Humidifier CA-605T Smart is subjected to strict testing procedures before leaving the factory. If within 2 years from the date of purchase the product does not perform according to the specifications, because of factory defects, the purchaser is entitled to free repairs or replacement of parts upon presentation of this warranty (provided that the malfunction or damage to the device and/or parts occurred under normal operating conditions). What is covered: All parts defective in material and workmanship. For how long: two years from purchase date. What we will do: Repair or replace any defective parts.

Other Conditions
The provisions of this warranty are in lieu of any other written warranty whether express or implied, written or oral, including any warranty of merchantability or fitness for a particular purpose. The manufacturer’s maximum liability shall not exceed the actual purchase price paid by you for the product. In no event shall the manufacturer be liable for special, incidental, consequential, or indirect damages. This warranty does not cover a defect that has resulted from improper or unreasonable use or maintenance, faulty assembly, accident, natural catastrophes, improper packing, or unauthorized tampering, alteration, or modification as
determined solely by us. This warranty is void if the label bearing the serial number has been removed or defaced.

Never put other pure essential oils or other additives into the water tank resp. the water basin! Even a small quantity can damage the plastic and cause cracks.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Clean Air Optima User Manuals

Related Manuals