hygger HG-020 Wave Maker User Manual

hygger HG-020 Wave Maker

E-mail: [email protected]

hygger wave maker is come with new design but simple. The strong magnetic & suction base can be easily and sturdy installed on the wall. Please read the manual carefully before using.

PRODUCT FEATURES

• Circulate the aquarium water:Simulates the natural currents of natural bodies of water,such as rivers or oceans, providing exercise and healthy flow for your tank. It is designed to stir up debris and remove dead spots of your tank. In addition, the pump can be used to increase the oxygen level of the water.
• Quiet and powerful :Two heads makes strong waves to circulate the water quietly and efficiently.The magnetic and suction base reduces noise and protect the glass when the pump running.
• 360 Degree Rotation:The head rotates a full 360 degree,offering full control of the direction of flow,creating natural water motion.
• Easy to install and use: Easy installation with magnetic holders.
• Designed to be used on less than 0.4 7inch thick tank.

PRODUCT PARAMETERS

Model| Power of water pump| Max volume of flow| Applicable Tank
---|---|---|---
HG-020 S| 110-120V 60Hz 5W

220-240V 50Hz 5W

| 21050 GPH (24000 LPH)| 40-110 Gallon (151-416L)
HG-020 M| 110-120V 60Hz 12W

220-240V 50Hz 12W

| 22100 GPH (210000 LPH)| 110-240 Gallon (416-908L)

PRODUCT INSTRUCTIONS

1. Front cover
2. Impeller
3. Pump
4. Fixture
5. Magnetic base
6. Suction base

INSTALLATION

1. Unpack the box and check that if the pump and other accessories are included. If any parts are missing, please contact seller.
2. Insert the fixture of the magnetic base into the pump.
3. Apart the magnetic base, take off the silicon mats. Due to The base is very magnetic, the silicon mats can prevent your hands from being pinched. If fish tank glass is thin, you can keep the cushion on the base to reduce vibration and noise.
4. Adjust the required angle of the wave maker, then install it at the position 6-8inch below water level. Place the magnetic and suction base mount outside the tank.
5. Power it on.

MAINTENACE

maker to ensure its efficient operation

1. Shut off the power
2. Cleaning the debris in the pump, first, rotate the front cover of wave maker, and then remove the impeller, wipe the impeller with a soft cloth and clean the pump with water.

3. lnstall back the pump,first, put the impeller into the pump, like the Fig.3 Then install the impeller and the front cover, like the Fig.4 At the last rotate the front cover tightly,like the Fig.5

ATTENTION

• Please read the manual carefully before use and follow all instructions.
• If the wave maker is stuck, then it needs to be cleaned and reassembled.
• Running dry is not allowed to guarantee the product’s performance.
• Please unplug the power before maintenance.
• Please remember that the temperature range for the wave maker is 32~113°F.

TROBLESHOOTING

power and
not work| after cleaning.| re-set the impeller.
or unusual noise.|  |
3.Check for fine grain sand if using sandy substrate.| 3.Change to larger particle sand or ensure the filter intake is not near sand.
 | 4.Check if impeller unit is worn out.| 4.Replace the impeller unit.

WARNING
To avoid possible electrical shock, basic safety precautions should be observed including the following:

1. Read and follow this user manual strictly.
2. DANGER-To avoid possible electric shock, special care should be taken. For each of the following situations, do not attempt to repair it yourself; return it to an authorized service facility for maintenance or discard it.
   • Carefully examine after installation. It should not be plugged in if there is water on parts that are not supposed to be wet.
   • Do not use it if it has a damaged cord or plug, if it is malfunctioning or if it is dropped or damaged in any manner. T he power cord of it cannot be replaced; if the cord is damaged, it should be discarded.
   • To avoid the possibility of its plug getting wet, position the aquarium stand and tank to one side of a wall-mounted receptacle to prevent water from dripping onto the receptacle or plug. A “drip loop”, as shown in the picture below, should be arranged by the user for each cord connecting the light to the receptacle. The “drip loop” is the part of the cord below the level of the receptacle or the connector. If an extension cord is used, prevent water from traveling along the cord and coming in contact with the receptacle. If the plug or receptacle does get wet, DO NOT unplug the cord. Disconnect the fuse to the circuit breaker that supplies power to it. Then unplug and examine for the presence of water in the receptacle.
3. Close supervision is necessary when it is used near children.
4. To avoid injury, do not touch the moving or hot parts.
5. Make sure it is securely installed before using it.
6. Read and observe all the important notices on it.
7. If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.
8.  lt is intended FOR HOUSEHOLD USE ONLY.
9. SAVE THIS USER MANUAL.

WARRANTY

• 1-year free warranty.
• 1-month free return.
• Free replacement for 3 months.

DISPOSAL

Do not dispose this product as unsorted municipal waste. This product must not be disposed of together with the domestic waste it must be disposed of at an authorized place for recycling of electrical and electronic appliances. By collecting and recycling waste, you help save natural resources, and make sure the product is disposed in an environmentally friendly way.

Contact information

• Brand Owner: Shenzhen Mago Trading Co.,Ltd
• Add: Bantian Group Business Central,Longgang District,
• Shenzhen City,Guangdong Province,China
• Website: www.hygger-online.com
• E-mail: [email protected]
• WhatsApp: + 12028664104
  Please provide your amazon order id(amazon invoice)and shipping address if you have any problems.

FOR MORE INFO

ABOUT COMPANY

• Company:E-CrossStu GmbH
  • Address: Mainzer Landstr.69,60329
  • Frankfurt am Main
  • E-mail: [email protected]
  • Tel:+49 69332967674
• GET Product Service Ltd.
  • Beacon House Stokenchurch Business Park,Ibstone Rd,Stokenchurch
  • High Wycombe HP14 3FE UK
  • [email protected]
  • +447419325266

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>