HORIZON HOBBY Bajarey Ford Raptor 1:10 Scale 4WD Instruction Manual
- June 7, 2024
- HORIZON HOBBY
Table of Contents
Bajarey Ford Raptor 1:10 Scale 4WD
FORD RAPTOR 1:10 SCALE 4WD
INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI
Before operating this vehicle, please read all printed materials thoroughly. Horizon Hobby is not responsible for inadvertent errors in this manual.
EN
NOTICE
All instructions, warranties and other collateral documents are subject to
change at the sole discretion of Horizon Hobby, LLC. For up-to-date product
literature, visit horizonhobby.com or towerhobbies.com and click on the
support or resources tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate
various levels of potential harm when operating this product: WARNING:
Procedures, which if not properly followed, create the probability of property
damage, collateral damage, and serious injury OR create a high probability of
superficial injury. CAUTION: Procedures, which if not properly followed,
create the probability of physical property damage AND a possibility of
serious injury. NOTICE: Procedures, which if not properly followed, create a
possibility of physical property damage AND a little or no possibility of
injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product
correctly can result in damage to the product, personal property and cause
serious injury.
This is a sophisticated hobby product. It must be operated with caution and
common sense and requires some basic mechanical ability. Failure to operate
this Product in a safe and responsible manner could result in injury or damage
to the product or other property. This product is not intended for use by
children without direct adult supervision. Do not use with incompatible
components or alter this product in any way outside of the instructions
provided by Horizon Hobby, LLC. This manual contains instructions for safety,
operation and maintenance. It is essential to read and follow all the
instructions and warnings in the manual, prior to assembly, setup or use, in
order to operate correctly and avoid damage or serious injury.
WARNING AGAINST COUNTERFEIT PRODUCTS Always purchase from a Horizon Hobby, LLC
authorized dealer to ensure authentic high-quality Spektrum product. Horizon
Hobby, LLC disclaims all support and warranty with regards, but not limited
to, compatibility and performance of counterfeit products or products claiming
compatibility with DSM or Spektrum technology.
Age Recommendation: Not for children under 14 years. This is not a toy.
SAFETY PRECAUTIONS AND WARNINGS
As the user of this product, you are solely responsible for operating in a
manner that does not endanger yourself and others or result in damage to the
product or property of others. This model is controlled by a radio signal
subject to interference from many sources outside your control. This
interference can cause momentary loss of control, so it is advisable to always
keep a safe distance in all directions around your model as this margin will
help avoid collisions or injury.
· Never operate your model with low transmitter batteries. · Always operate
your model in open spaces away from full-size vehicles, traffic and people. ·
Never operate the model in the street or in populated areas for any reason. ·
Carefully follow the directions and warnings for this and any optional support
equipment
(chargers, rechargeable battery packs, etc.) you use. · Keep all chemicals,
small parts and anything electrical out of the reach of children.
· Never lick or place any portion of the model in your mouth as it could cause
serious injury or even death.
· Exercise caution when using tools and sharp instruments.
· Take care during maintenance as some parts may have sharp edges.
· Immediately after using your model, do NOT touch equipment such as the
motor, electronic speed control and battery, because they generate high
temperatures. You may burn yourself seriously touching them.
· Do not put fingers or any objects inside rotating and moving parts, as this
may cause damage or serious injury.
· Always turn on your transmitter before you turn on the receiver in the car.
Always turn off the receiver before turning your transmitter off.
· Keep the wheels of the model off the ground when checking the operation of
the radio equipment.
TABLE OF CONTENTS
CONTENTS ………………………………………………………………………………………………….. 2 WATER-RESISTANT VEHICLE
WITH WATERPROOF ELECTRONICS…………………….3 QUICK
START……………………………………………………………………………………………….3 CHARGING THE BATTERY
……………………………………………………………………………..3 INSTALLING THE
BATTERY…………………………………………………………………………….4 SPEKTRUM DX2E RADIO
SYSTEM…………………………………………………………………4
INSTALLING THE TRANSMITTER BATTERIES…………………………………………………..4 SRS6000 AVC
TECHNOLOGY RECEIVER ……………………………………………………….4 STABILITY ASSIST
RECEIVER…………………………………………………………………………5 DRIVING
PRECAUTIONS……………………………………………………………………………….5 POWERING ON THE VEHICLE
………………………………………………………………………..5 BEFORE RUNNING YOUR VEHICLE
………………………………………………………………..5 AVC SENSITIVITY …………………………………………………………………………………………
5 DISABLING AVC TECHNOLOGY……………………………………………………………………..6 PERFORMING A CONTROL
DIRECTION TEST………………………………………………….6 RUN
TIME…………………………………………………………………………………………………….6 CHANGING THE TRAVEL ADJUST
SETTINGS…………………………………………………..6 DYNAMITE FUZE 130A SENSORLESS BRUSHLESS ESC
…………………………………..6 DYNAMITE FUZE 3800KV BRUSHLESS MOTOR………………………………………………8
TROUBLESHOOTING GUIDE ………………………………………………………………………….8 LIMITED WARRANTY
……………………………………………………………………………………9 FCC INFORMATION
………………………………………………………………………………..10 IC INFORMATION
…………………………………………………………………………………..10 WARRANTY AND SERVICE CONTACT INFORMATION
……………………………………10 COMPLIANCE INFORMATION FOR THE EUROPEAN UNION…………………………..10
REPLACEMENT PARTS …………………………………………………………………………..3536 OPTIONAL
PARTS……………………………………………………………………………………….36 EXPLODED VIEWS
…………………………………………………………………………………3741
CONTENTS
REGISTER YOUR LOSI PRODUCT ONLINE
Register your vehicle now and be the first to find out about the latest option
parts, product updates and more. Click on the Support tab at www.losi.com and
follow the product registration link to stay connected.
COMPONENTS
· Losi® Ford Raptor Baja Rey® RTR with AVC® technology: 1/10-Scale 4WD Desert
Truck · SpektrumTM DX2E 2.4GHz Transmitter (SPM2335) · SpektrumTM 6-Channel
DSMR® AVC Surface Receiver (SPMSRS6000) · SpektrumTM 9KG 23T Waterproof Servo
(SPMS605) · Dynamite® FuzeTM 130A Sensorless Brushless Waterproof ESC
(DYN4955) · Dynamite® FuzeTM 550 Brushless Motor 3800Kv (DYNS1616) · 4 AA
batteries (for transmitter)
2
FORD®® RAPTOR BAJA REY®®: 1:10 4WD RTR · INSTRUCTION MANUAL
EN
WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS
Your new Horizon Hobby vehicle has been designed and built with a combination
of waterproof and water-resistant components to allow you to operate the
product in many “wet conditions,” including puddles, creeks, wet grass, snow
and even rain.
While the entire vehicle is highly water-resistant, it is not completely
waterproof and your vehicle should NOT be treated like a submarine. The
various electronic components used in the vehicle, such as the Electronic
Speed Control (ESC), servo(s) and receiver are waterproof, however, most of
the mechanical components are water-resistant and should not be submerged.
Metal parts, including the bearings, hinge pins, screws and nuts, as well as
the contacts in the electrical cables, will be susceptible to corrosion if
additional maintenance is not performed after running in wet conditions. To
maximize the long-term performance of your vehicle and to keep the warranty
intact, the procedures described in the “Wet Conditions Maintenance” section
below must be performed regularly if you choose to run in wet conditions. If
you are not willing to perform the additional care and maintenance required,
then you should not operate the vehicle in those conditions.
CAUTION: Failure to exercise caution while using this product and complying
with the following precautions could result in product malfunction and/or void
the warranty.
· Driving in wet conditions can reduce the life of the motor. The additional
resistance of operating in water causes excess strain. Alter the gear ratio by
using a smaller pinion or larger spur gear. This will increase torque (and
motor life) when running in mud, deeper puddles, or any wet conditions that
will increase the load on the motor for an extended period of time.
WET CONDITIONS MAINTENANCE
· Drain any water that has collected in the tires by spinning them at high
speed. With the body removed, place the vehicle upside down and pull full
throttle for a few short bursts until the water has been removed.
CAUTION: Always keep hands, fingers, tools and any loose or hanging objects
away from rotating parts when performing the above drying technique.
· Remove the battery pack(s) and dry the contacts. If you have an air
compressor or a can of compressed air, blow out any water that may be inside
the recessed connector housing.
· Remove the tires/wheels from the vehicle and gently rinse the mud and dirt
off with a garden hose. Avoid rinsing the bearings and transmission.
GENERAL PRECAUTIONS
· Read through the wet conditions maintenance procedures and make sure that
you have all the tools you will need to properly maintain your vehicle.
· Not all batteries can be used in wet conditions. Consult the battery
manufacturer before use. Caution should be taken when using Li-Po batteries in
wet conditions.
· Most transmitters are not water-resistant. Consult your transmitter’s manual
or the manufacturer before operation.
· Never operate your transmitter or vehicle where lightning may be present.
· Do not operate your vehicle where it could come in contact with salt water
(ocean water or water on salt-covered roads), contaminated or polluted water.
Salt water is very conductive and highly corrosive, so use caution.
· Even minimal water contact can reduce the life of your motor if it has not
been certified as water-resistant or waterproof. If the motor becomes
excessively wet, apply very light throttle until the water is mostly removed
from the motor. Running a wet motor at high speeds may rapidly damage the
motor.
NOTICE: Never use a pressure washer to clean your vehicle.
· Use an air compressor or a can of compressed air to dry the vehicle and help
remove any water that may have gotten into small crevices or corners.
· Spray the bearings, drive train, fasteners and other metal parts with a
water-displacing light oil. Do not spray the motor.
· Let the vehicle air dry before you store it. Water (and oil) may continue to
drip for a few hours.
· Increase the frequency of disassembly, inspection and lubrication of the
following: – Front and rear axle hub assembly bearings. – All transmission
cases, gears and differentials. – Motor–clean with an aerosol motor cleaner
and re-oil the bushings with lightweight motor oil.
QUICK START
Please read the entire manual to gain a full understanding of the Baja Rey
vehicle, fine-tuning the setup and performing maintenance.
1. Read the safety precautions found in this manual.
2. Charge a battery for the vehicle. Refer to the included charging warnings
and instructions for battery charging information.
3. Install the AA batteries in the transmitter. Only use alkaline or
rechargeable batteries.
4. Install the fully charged battery in the vehicle.
5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC
to initialize. Always power the transmitter ON before the vehicle and power it
OFF after the vehicle has been powered OFF.
6. Check the steering and throttle control directions. Verify that the servos
are moving in the correct direction.
7. Drive your vehicle.
8. Perform any necessary maintenance.
CHARGING THE BATTERY
Choose a battery designed to work with the Dynamite® FuzeTM 130A Sensorless BL
Waterproof ESC. We recommend the Dynamite® 7.4 5000mAh 2S 30C LiPo: Hardcase
with EC3TM connector (DYN9005EC). Choose a charger designed to charge 2S Li-Po
batteries. We recommend the Dynamite® ProphetTM Sport Li-Po 35W AC Battery Charger (DYNC2005CA). Refer to your battery and charger manuals for usage, safety, and charging information.
FORD®® RAPTOR BAJA REY®®: 1:10 4WD RTR · INSTRUCTION MANUAL
3
EN
INSTALLING THE BATTERY
1. Ensure the ESC is powered OFF. 2. Slide the button to the right to release the battery door. 3. Install the fully charged battery in the vehicle. 4. Connect the battery to the ESC. 5. Close the battery door and slide the battery door button to the left to secure it. 6. Power ON the transmitter, then the vehicle.
SPEKTRUMTM DX2E RADIO SYSTEM
7 6 5
8 9 10
11
12
4
3
2
1
4
1. Steering Wheel Controls direction (left/right) of the model
13
2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model
3. BIND Button Puts the transmitter into Bind Mode
4. ON/OFF Switch Turns the power ON/OFF for the transmitter
5. TH.REV Reverses function of the speed control when pulled back or pushed forward
6. Indicator Lights
– Solid green light–indicates adequate battery power
– Flashing green light–indicates the battery voltage is critically low. Replace batteries
7. ST. REV Reverses the function of the steering when the wheels is turned left or right
8. ST Trim Adjusts the steering center point
9. TH Trim Adjusts the throttle neutral point
10. TH Limiter Limits throttle output to 50, 70 or 100%.
11. 3-Position Switch Used to control a third channel and is preset at -100%/Neutral/100%
12. ST Rate Adjusts the sensitivity of AVC technology
13. Antenna Transmits the signal to the model
INSTALLING THE TRANSMITTER BATTERIES
1. Push in the battery cover a small amount to release the retaining tab,
then remove the cover. 2. Install 4 AA batteries, taking care to align the
battery polarity to the diagram in the
transmitter’s battery case. 3. Carefully reinstall the battery cover by
aligning the tabs with the slots on the transmitter.
For more information on the transmitter, go to www.horizonhobby.com and click
on the support tab for the Spektrum DX2E to download the instruction manual.
CAUTION: Never remove the transmitter batteries while the model is powered ON.
Loss of model control, damage, or injury may occur.
CAUTION: If using rechargeable batteries, charge only rechargeable batteries.
Charging non-rechargeable batteries may cause the batteries to burst,
resulting in injury to persons and/or damage to property.
CAUTION: Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to national regulations.
SRS6000 AVC TECHNOLOGY RECEIVER
Antenna
Bind/Battery Aux 4/Disable
Aux 3 Aux 2 Aux 1 Throttle Steering
AUX CHANNELS
The Aux channels can operate as additional servo channels, or as a power
supply for a personal transponder.
If AVC is active, only 4 channels; Steering, Throttle, AUX3 and AUX4 are
operational. The remaining Aux channels can be used to power a personal
transponder or lights.
If AVC is disabled (see DISABLING THE STABILITY ASSIST FUNCTION), all 6
channels including the Aux channels can operate as servo channels.
FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · INSTRUCTION MANUAL
EN
STABILITY ASSIST RECEIVER
AVC® ACTIVE VEHICLE CONTROLTM
The Spektrum receiver features Active Vehicle ControlTM (AVC®) technology that
responds similar to traction control in full-scale vehicles. In addition to
traction control, AVC technology also increases steering stability during high
speed driving or while driving over rough terrain. As you increase the AVC
sensitivity, the system increases steering stability and traction control,
similar to reducing the amount of steering rate in a computer transmitter.
Reducing the sensitivity value increases the amount of steering control from
the transmitter. The receiver also enables you to quickly turn AVC on or off
if you participate in organized racing.
IMPORTANT: You must use digital servos with the AVC receiver. Do not use
analog servos as they willl reduce the performance of the system and may cause
overheating.
CALIBRATING THE RECEIVER
1. With the vehicle on a flat, level surface, insert the Bind Plug in the
BIND port on the receiver.
2. Connect a fully charged battery pack to the ESC. 3. Power on the ESC. The
orange LED flashes, indicating the receiver is in bind mode. 4. Center the ST
TRIM and TH TRIM dials on the transmitter. 5. Press and hold the BIND button
while powering on the transmitter. 6. Release the BIND button when the orange
LED slowly flashes. The transmitter and receiver
are linked when the orange LED is solid. 7. Pull the transmitter trigger to
Full Throttle. 8. Push the transmitter trigger to Full Brake, then return the
trigger to center. 9. Turn the transmitter steering wheel to Full Right. 10.
Turn the transmitter steering wheel to Full Left, then return the steering
wheel to center.
The orange LED flashes once. 11. Remove the Bind Plug, then power off the
receiver to save the settings. 12. Power off the transmitter.
FORWARD
BRAKE/REVERSE
DRIVING PRECAUTIONS
· Maintain sight of the vehicle at all times. · Routinely inspect the vehicle
for loose wheel hardware. · Routinely inspect the steering assembly for any
loose hardware. Driving the vehicle
off-road can cause fasteners to loosen over time. · Do not drive the vehicle
in tall grass. Doing so can damage the vehicle or electronics. · Stop driving
the vehicle when you notice a lack of power. Driving the vehicle when
the battery is discharged can cause the receiver to power off. If the receiver
loses power, you will lose control of the vehicle. Damage due to an over-
discharged Li-Po battery is not covered under warranty.
CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries
discharged to a voltage lower than the lowest approved voltage may become
damaged, resulting in loss of performance and potential fire when batteries
are charged.
· Do not apply forward or reverse throttle if the vehicle is stuck. Applying
throttle in this instance can damage the motor or ESC.
· After driving the vehicle, allow the electronics to cool before driving the
vehicle again.
IMPORTANT: Keep wires away from all moving parts.
POWERING ON THE VEHICLE
1. Center the ST TRIM and TH TRIM dials on the transmitter. 2. Power on the
transmitter. 3. Remove the body from the vehicle. 4. Connect a fully charged
battery pack to the ESC. 5. Power on the ESC.
IMPORTANT: The vehicle MUST remain on a flat, level surface and motionless for
at least 5 seconds.
BEFORE RUNNING YOUR VEHICLE
1. Check for free suspension movement. All suspension arms and steering
components should move freely. Any binds will cause the vehicle to handle
poorly.
2. Charge a battery pack. Always charge the battery pack as per the battery
and/or charger manufacturers’ instructions.
3. Set the transmitter steering trim. Follow the instructions to set the
steering trim/subtrim so that the vehicle drives straight with no input to the
steering.
4. Perform a Control Direction Test.
AVC® SENSITIVITY
The ST RATE dial adjusts the sensitivity, or stability, value in the receiver.
If you increase the sensitivity, the AVC® system becomes more sensitive to the
vehicle drifting left or right. You would use maximum sensitivity during high
speed driving or drag racing, when you want the vehicle to stay in a straight
line. As the sensitivity value increases, the amount of steering travel
decreases.
Turn the ST RATE knob counter-clockwise to reduce the sensitivity.
Turn the ST RATE knob clockwise to increase the sensitivity.
IMPORTANT: The ST RATE knob will only adjust the sensitivity when the
transmitter is bound to a DSMR® receiver. When the transmitter is bound to a
DSM®, DSM2® or DSM Marine receiver, the ST RATE knob controls the steering
dual rate.
FORD® RRAAPPTTOORR BBAAJJAA RREEYY®®:: 11::1100 44WWDD RRTTRR ·· IINNSSTTRRUUCCTTIIOONN MMAANNUUAALL
5
EN
DISABLING AVC® TECHNOLOGY
If you participate in organized racing, you may be required to turn AVC off.
To turn AVC off: 1. Insert a Bind Plug in the BIND port on the receiver. 2.
Insert a second Bing Plug in the DISABLE port on the receiver. 3. Connect a
fully charged battery pack to the ESC. 4. Power on the ESC. The orange LED
flashes, indicating the receiver is in bind mode. 5. Center the ST TRIM and TH
TRIM dials on the transmitter. 6. Press and hold the BIND button while
powering on the transmitter. 7. Release the BIND button when the orange LED
slowly flashes. The transmitter and receiver
are linked when the orange LED is solid. 8. Pull the transmitter trigger to
Full Throttle. 9. Push the transmitter trigger to Full Brake, then return the
trigger to center. 10. Turn the transmitter steering wheel to Full Right. 11.
Turn the transmitter steering wheel to Full Left, then return the steering
wheel to center.
The orange LED flashes once. 12. Remove the Bind Plugs, then power off the
receiver to save the settings. The receiver will
continuously blink to indicate AVC is disabled. 13. Power off the transmitter.
IMPORTANT: You must calibrate the receiver each time it is placed in bind
mode. To activate AVC, see the steps in “Calibrating the Receiver.”
PERFORMING A CONTROL DIRECTION TEST
Perform a control test with the vehicle wheels off the ground. If the wheels
rotate after the vehicle is powered ON, adjust the TH TRIM knob until they
stop. To make the wheels move forward, pull the trigger. To reverse them, wait
for the wheels to stop, then push the trigger. When moving forward, the wheels
should maintain a straight line without any steering wheel input. If not,
adjust the ST TRIM knob, so the wheels maintain a straight line without having
to turn the steering wheel.
RUN TIME
CHANGING THE TRAVEL ADJUST SETTINGS
The largest factor in run time is the capacity of the battery pack. A larger
mAh rating increases the amount of run time experienced.
The condition of a battery pack is also an important factor in both run time
and speed. The battery connectors may become hot during driving. Batteries
will lose performance and capacity over time.
Driving the vehicle from a stop to full speed repeatedly will damage the
batteries and electronics over time. Sudden acceleration will also lead to
shorter run times.
TO IMPROVE RUN TIMES
· Keep your vehicle clean and well maintained.
· Allow more airflow to the ESC and motor.
· Change the gearing to a lower ratio. A lower ratio decreases the operating
temperature of the electronics. Use a smaller pinion gear or larger spur gear
to lower the gear ratio.
· Use a battery pack with a higher mAh rating.
· Use the optimum charger to charge battery packs. (Visit your local hobby
dealer for more information.)
1. Hold the trigger in the full brake position and turn the steering wheel to
Full Right while powering on the transmitter. The LED flashes rapidly,
indicating the programming mode is active.
2. Throttle End Point: Continue holding full throttle. Turn the TH TRIM knob
to adjust the full throttle end point.
3. Brake End Point: Hold the trigger in the full brake position. Turn the TH
TRIM knob to adjust the full brake end point. Return the trigger to the center
position.
4. Left Steering End Point: Hold the steering wheel in the full left
position. Turn the ST TRIM knob to adjust the left end point.
5. Right Steering End Point: Hold the steering wheel in the full right
position. Turn the ST TRIM knob to adjust the right end point. Return the
steering wheel to the center position.
6. Power off the transmitter to save the travel adjust settings. The minimum
travel is 75%, and the maximum travel is 150%.
IMPORTANT: If the travel is changed on the DX2E, you must rebind and calibrate
the receiver.
DYNAMITE® FUZETM 130A SENSORLESS BRUSHLESS ESC
SPECIFICATIONS
Type Constant/Peak Resistance Function Operation Input Voltage BEC Output Overload Protection Dimensions (LxWxH) Weight
Sensorless 130A/760A 0.0004 Ohm Forward/BrakeForward/Brake Reverse Proportional forward, proportional reverse with braking delay 7.4V14.8V (The motor in this vehicle will not support 14.8V.) 6V/3A Thermal 53.5mm x 36mm x 36mm 79 g
ESC LED STATUS
· No ESC LEDs will glow when there is no throttle input from the transmitter.
· The red ESC LED glows when there is any throttle input from the transmitter.
AUDIBLE WARNING TONES
1. Input Voltage: The ESC checks the input voltage when it is powered ON. If
a voltage problem is detected, the ESC continuously sounds 2 beeps with a 1
second pause (xx-xx-xx). Power OFF the ESC and ensure the connections are
secure and that the battery power is not too low for safe operation.
2. Radio Connection: The ESC checks radio signal input when it is powered ON.
If a problem is detected, the ESC continuously sounds 1 beep with a 2 second
pause (x–x–x). Power OFF the ESC and ensure the radio system is operating
correctly.
For sensorless brushless motors: 1. Connect the ESC terminal A (typically
designated by a blue wire) to the motor’s terminal
A (red wire on a Dynamite® FuzeTM sensorless motor). This may also be changed
in Programming Item 12, Motor Rotation, without changing wire connections.
2. Connect the ESC terminal B (typically designated by a yellow wire) to the
motor’s terminal B (blue wire on a Dynamite® FuzeTM sensorless motor).
3. Connect the ESC terminal C (typically designated by an orange wire) to the
motor’s terminal C (black wire on a Dynamite® FuzeTM sensorless motor).
NOTICE: Always disconnect the battery from the ESC when you have finished
operating your vehicle. The ESC’s switch only controls power to the receiver
and servos. The ESC will continue to draw current when connected to the
battery, resulting in possible damage to the battery through over discharge.
ESC CALIBRATION PROCEDURE
Ensure proper ESC function by calibrating the ESC to your transmitter inputs.
- Power OFF the ESC.
2. Ensure your transmitter is powered ON, the throttle is not reversed, the throttle trim is neutral and the throttle travel range is at 100%. Disable any special functions such as ABS, etc.
3. Press the SET button while powering ON the ESC. Release the button as soon as the red LED starts to flash.
4. Calibrate the throttle points by pressing the SET button once after each step. – Neutral (1 flash)–leave the throttle at rest, untouched – Full throttle (2 flashes)–pull the throttle fully back – Full brake/reverse (3 flashes)–push the throttle fully forward
5. The motor will run 3 seconds after the last step is completed.
Tip: If the motor turns in the wrong direction, reverse the connection of any 2 outside motor wires. The center wire must remain in the center and cannot be moved to another motor tab.
6
FORD®TERNA-PSTCOBREBRATJRA, ARVECY:®1: :11:0104W4WDDSCRBTRE · INSTRUCTION MANUAL
ESC FUNCTIONS AND MODES
The ESC includes programming options so you can adjust the way your vehicle
performs. Refer to the included settings table to adjust the ESC for your
driving conditions.
ESC PROGRAMMING PROCEDURE
Programming is accomplished using the SET button on the ON/OFF switch or
Digital Program Box (DYNS3005). 1. Connect a fully charged battery to the ESC.
2. Power ON the ESC using the ESC switch. 3. Hold the SET button for 1 second
until the green LED blinks, then release the SET button
to enter programming mode.
EN
4. Press and release the SET button as needed to get to the desired menu
option (the Green LED will blink corresponding to the menu item number).
Programming menu items 1 through 9 are accessible using the SET button on the
ESC. Programming menu items 10 and above are only accessible using the
optional ESC programming card. Programming of menu items 10 and 11 is only
possible after firmware updates to the ESC programming card.
5. When at the desired menu item, hold the SET button for 3 seconds until the
red LED blinks. 6. Press the SET button to move among the settings based on
how many times the red LED
blinks (Refer to the table for more information). 7. Save the setting by
holding the SET button for 3 seconds. 8. Power OFF the ESC switch and repeat
the instructions above to change other settings.
Tip: If desired, the ESC programming can be returned to default settings by
powering ON the ESC and holding the SET button for 5 seconds.
PROGRAMMABLE ITEMS Basic Items
1 Running Mode
2 Drag Brake Force
3 Low Voltage Cutoff
4 Start Mode
PROGRAMMABLE VALUE
1
2
3
Forward w/ brake Forward/Reverse w/ brake Forward/Reverse
0%
5%
10%
non-protection 2.6V/Cell
2.8V/Cell
Level 1
Level 2
Level 3
4
5
20% 3.0V/Cell Level 4
40% 3.2V/Cell Level 5
6
60% 3.4V/Cell Level 6
Default Settings
7
8
9
80%
100%
Level 7 Level 8 Level 9
PROGRAMMABLE ITEMS Advanced Items
5 Max Brake Force 6 Max Reverse Force 7 Initial Brake Force 8 Neutral Range 9
Timing 10 Reserved Item 11 Reserved Item 12 Motor Rotation 13 Li-Po Cells
PROGRAMMABLE VALUE
1
2
25%
50%
25%
50%
= Drag Brake Force 0%
6% (Narrow)
9% (Normal)
0.00º
3.75º
Counterclockwise Clockwise
Auto Calculate
2 Cells
3 75% 75% 20% 12% (Wide) 7.50º
4
5
6
100%
disable
100%
40%
11.25º 15.00º 18.75º
Default Settings
7
8
9
22.50º 26.25º
3 Cells
4 Cells 5 Cells 6 Cells
DESCRIPTIONS
1. Running Mode – Forward Only with Brake Intended for competition use, this
mode allows only forward and brake controls. – Forward/Reverse with Brake This
mode is the basic all-around mode, allowing forward, reverse and brake
controls. To engage reverse while moving forward, apply the brake until the
vehicle has come to a complete stop, release brake, then apply the brake
again. While braking or in reverse, engaging the throttle will result in the
vehicle immediately accelerating forward.
2. Drag Brake Force Adjusts the amount of brake automatically applied when
the throttle is returned to the neutral position. This simulates the engine
braking effect of a full-scale vehicle, allowing improved turn-in and your
vehicle’s general response to controls.
3. Low Voltage Cutoff This function helps to prevent battery over-discharge.
The ESC continuously monitors the battery’s voltage. If the voltage falls
below the voltage threshold for 2 seconds, the output power shuts off and the
red LED flashes twice repeatedly.
The cutoff threshold calculation is based on individual Li-Po cell voltage.
For Ni-MH batteries, if the voltage battery pack is higher than 9.0V, it will
be treated as a 3-cell Li-Po battery pack; if it is lower than 9.0V, it will
be treated as a 2-cell Li-Po battery pack. Example: for a 8.0V Ni-MH battery
pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po
battery pack and the low-voltage cut-off threshold will be 5.2V (2.6×2=5.2).
4. Start Mode (Punch) Sets the initial throttle punch when the car
accelerates. Level 1 gives a very soft initial acceleration and level 4 gives
a stronger initial acceleration.
5. Max Brake Force Adjusts the maximum braking force. A higher value provides
stronger braking, but can also cause the wheels to lock, resulting in loss of
control of the car.
6. Max Reverse Force This parameter adjusts the maximum power when travelling
in reverse.
7. Initial Brake Force (minimum brake) Adjusts the minimum amount of braking
power when the brakes engage. The default value is equal to the drag brake
value. A high value can lock the wheels when the brake is used.
8. Neutral Range Adjusts the throttle sensitivity around the neutral point. A
higher value results in the throttle having to be moved more for the vehicle
to move forward, backward or brake.
9. Timing Adjusts the motor drive current timing. More timing gives more
performance, but can lower efficiency and cause damage to the motor and/or ESC
by overload or overheating.
NOTICE: Always ensure the motor timing is set correctly. Failure to set the
motor timing correctly can result in damage to the motor and ESC. Refer to the
manufacturer instructions for recommended timing settings.
The Following Programmable Items require the optional Digital ESC Program Box:
10. and 11. Available Items are subject to firmware updates to the ESC and
the optional digital program box.
12. Motor Rotation Allows you to make this change in the ESC so no wires need
to be changed between the ESC and the motor.
13. Li-Po Cells Allows the ESC to automatically detect or manually set the
number of cells in your Li-Po battery back.
FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · INSTRUCTION MANUAL
7
EN
DYNAMITE® FUZETM 3800KV BRUSHLESS MOTOR
PRECAUTIONS
· Never touch moving parts.
· Never disassemble while the batteries are installed.
· Always let parts cool before touching.
GEARING
Your vehicle has been equipped with the optimal gearing for the stock
platform. It offers an ideal balance between speed, power and efficiency.
Should you decide to customize your vehicle with optional batteries or motors,
it may be necessary for you to change the pinion or spur gear.
Installing a pinion gear with fewer teeth or a spur gear with more teeth will provide greater torque but will reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with fewer teeth will reduce torque and increase top speed. Care should be taken when installing larger pinion gears as this can “overgear” the vehicle, resulting in overheating of the motor and ESC. When testing different gearing options, pay close attention to the temperature of the motor and speed control to ensure you are operating within the temperature range of the components. The motor or ESC should never be so hot that it cannot be touched. If temperatures are too hot, a different gearing combination with a lower pinion gear and/or higher spur gear is suggested.
TROUBLESHOOTING GUIDE
PROBLEM
Vehicle does not operate
Motor runs but wheels do not rotate
Steering does not work Will not turn one direction Motor does not run
ESC gets hot Poor run time and/or sluggish acceleration
Poor range and/or glitching
POSSIBLE CAUSE
Battery not charged or plugged in ESC switch not “On” Transmitter not “On” or
low battery Pinion not meshing with spur gear Pinion spinning on motor shaft
Transmission gears stripped Drive pin broken Servo plug not in receiver
properly Servo gears or motor damaged Servo gears damaged Motor wire solder
joint is damaged Motor wire broken ESC damaged Motor over-geared Driveline
bound up Battery pack not fully charged Charger not allowing full charge
Driveline bound up Transmitter batteries low Vehicle battery low Loose plugs
or wires
SOLUTION
Charge battery/plug in Turn on ESC switch Turn on/replace batteries Adjust
pinion/spur mesh Tighten pinion gear setscrew on motor shaft flat spot Replace
transmission gears Check and replace drive pin Make sure the steering servo
plug is connected to the receiver steering channel, noting proper polarity
Replace or repair servo Replace or repair servo Resolder the motor wire with
the proper equipment Repair or replace as needed Contact Horizon Hobby Product
Support Use smaller pinion or larger spur gear Check wheels and transmission
for binding Recharge battery Try another charger Check wheels, transmission
for binding Check and replace Recharge battery Check all wire connections and
plugs
8
FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · INSTRUCTION MANUAL
EN
2-YEAR LIMITED WARRANTY
What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the
original purchaser that the product purchased (the “Product”) will be free
from defects in materials and workmanship for a period of 2 years from the
date of purchase.
What is Not Covered This warranty is not transferable and does not cover (i)
cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse,
negligence, commercial use, or due to improper use, installation, operation or
maintenance, (iii) modification of or to any part of the Product, (iv)
attempted service by anyone other than a Horizon Hobby authorized service
center, (v) Product not purchased from an authorized Horizon dealer, or (vi)
Product not compliant with applicable technical regulations or (vii) use that
violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy Horizon’s sole obligation and purchaser’s sole and
exclusive remedy shall be that Horizon will, at its option, either (i)
service, or (ii) replace, any Product determined by Horizon to be defective.
Horizon reserves the right to inspect any and all Product(s) involved in a
warranty claim. Service or replacement decisions are at the sole discretion of
Horizon. Proof of purchase is required for all warranty claims. SERVICE OR
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY.
Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN
CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF
LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. Further, in no event shall the liability of Horizon exceed the
individual price of the Product on which liability is asserted. As Horizon has
no control over use, setup, final assembly, modification or misuse, no
liability shall be assumed nor accepted for any resulting damage or injury. By
the act of use, setup or assembly, the user accepts all resulting liability.
If you as the purchaser or user are not prepared to accept the liability
associated with the use of the Product, purchaser is advised to return the
Product immediately in new and unused condition to the place of purchase.
Law These terms are governed by Illinois law (without regard to conflict of
law principals). This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state. Horizon reserves the
right to change or modify this warranty at any time without notice.
WARRANTY SERVICES Questions, Assistance, and Services Your local hobby store
and/or place of purchase cannot provide warranty support or service. Once
assembly, setup or use of the Product has been started, you must contact your
local
distributor or Horizon directly. This will enable Horizon to better answer
your questions and service you in the event that you may need any assistance.
For questions or assistance, please visit our website at www.horizonhobby.com,
submit a Product Support Inquiry, or call the toll free telephone number
referenced in the Warranty and Service Contact Information section to speak
with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online Service
Request submission process found on our website or call Horizon to obtain a
Return Merchandise Authorization (RMA) number. Pack the Product securely using
a shipping carton. Please note that original boxes may be included, but are
not designed to withstand the rigors of shipping without additional
protection. Ship via a carrier that provides tracking and insurance for lost
or damaged parcels, as Horizon is not responsible for merchandise until it
arrives and is accepted at our facility. An Online Service Request is
available at http://www.horizonhobby.com/content/_servicecenter_render-
service-center. If you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions for submitting
your product for service. When calling Horizon, you will be asked to provide
your complete name, street address, email address and phone number where you
can be reached during business hours. When sending product into Horizon,
please include your RMA number, a list of the included items, and a brief
summary of the problem. A copy of your original sales receipt must be included
for warranty consideration. Be sure your name, address, and RMA number are
clearly written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a
Li-Po battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt
verifying the proof-of-purchase date. Provided warranty conditions have been
met, your Product will be serviced or replaced free of charge. Service or
replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and
payment will be required without notification or estimate of the expense
unless the expense exceeds 50% of the retail purchase cost. By submitting the
item for service you are agreeing to payment of the service without
notification. Service estimates are available upon request. You must include
this request with your item submitted for service. Non-warranty service
estimates will be billed a minimum of ½ hour of labor. In addition you will be
billed for return freight. Horizon accepts money orders and cashier’s checks,
as well as Visa, MasterCard, American Express, and Discover cards. By
submitting any item to Horizon for service, you are agreeing to Horizon’s
Terms and Conditions found on our website http://www. horizonhobby.com/content
/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of
use and ownership. If received, a non-compliant Product will not be serviced.
Further, the sender will be responsible for arranging return shipment of the
un-serviced Product, through a carrier of the sender’s choice and at the
sender’s expense. Horizon will hold non-compliant Product for a period of 60
days from notification, after which it will be discarded.
10/15
FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · INSTRUCTION MANUAL
9
EN
Warranty and Service Contact Information
Country of Purchase
Horizon Hobby
Contact Information
Horizon Service Center (Repairs and Repair Requests)
servicecenter.horizonhobby.com/RequestForm/
United States of America
Horizon Product Support (Product Technical Assistance)
productsupport@horizonhobby.com 877-504-0233
Sales
websales@horizonhobby.com 800-338-4639
European Union
Horizon Technischer Service Sales: Horizon Hobby GmbH
service@horizonhobby.eu +49 (0) 4121 2655 100
*For the most up-to-date customer service contact information, please visit: www.horizonhobby.com/content/service-center-render-service-center
Address
2904 Research Road Champaign, Illinois 61822 USA*
Hanskampring 9 D 22885 Barsbüttel, Germany
FCC STATEMENT
FCC ID: BRWDX2EQ2UC
FCC ID: BRWDASRX12
This equipment has been tested and found to comply with the limits for Part 15
of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation
between the equipment and receiver. · Connect the equipment to an outlet on a
circuit different from that to which the receiver
is connected. · Consult the dealer or an experienced radio/TV technician for
help.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTICE: Modifications to this product will void the user’s authority to
operate this equipment.
IC INFORMATION
IC: 6157A-DX2EQ2UC IC: 6157A-AMRX12 This device complies with ISED Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device.
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product
is in compliance with the essential requirements and other relevant provisions
of the RED and EMC Directive.
A copy of the EU Declaration of Conformity is available online at:
http://www.horizonhobby.com/content/support-render-compliance.
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the
user’s responsibility to dispose of their waste equipment by handing it over
to a designated collections point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household
waste disposal service or where you purchased the product.
10
FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · INSTRUCTION MANUAL
IT
Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi
Part #
DYN4955
DYNS1616 LOSA3573 LOSA6250 LOSA6937 LOSA6940 LOSA6956 LOSA6957 LOSB3008
LOS43025 LOS230010
LOS230011
English
Fuze 130A Sensorless Brushless WP ESC
Fuze 550BL Motor, 3800Kv 1.0 Module Pitch Pinion, 13T Set Screws, 4mm & 5mm
(6) 5x10mm Sealed Ball Bearing (2) 6x12mm Sealed Ball Bearing (4) 12x18x4mm
Sealed Ball Bearing (2) 10x15x4mm Bearing 3x6x2.5mm Ball Bearing (2) Alpine
Wheel and Tire Mounted (2) Roll Cage Sides L&R
Top Bar, X-Bar,Cover & Tire Moun
LOS230012
LOS230013 LOS230020 LOS230066 LOS230067 LOS230068 LOS230069 LOS231005
LOS231006
Fr Bar, RR Body Mnt Bar, Bumper, Tower Support
Body Button Base & Top (22) Interior Set with Helmets, Clear King Shocks
Raptor Body Set Black Rhino Raptor Body Set Ford Raptor Body Adaptor Set Rear
Red LED Light Bar Rear Bulkhead,Fan Panel, Mudguards
Battery Tray,Door, Lock, 2S Spacer
LOS231007 Front Upper Arm/Shock Mount, RR Chassis Brace
LOS231008
LOS231010 LOS231011 LOS231012 LOS231013 LOS231058 LOS232001 LOS232002
LOS232003 LOS232004 LOS232005 LOS232006 LOS232007 LOS232008 LOS232009
LOS232010 LOS232012 LOS232013 LOS232014 LOS232051
LOS233001
LOS233002 LOS233003
LOS233004
LOS233005
LOS234002
Servo Mount, Steering Servo Set Plastic
Chassis Plate & Motor Cover Plate Center Chassis Brace & Standoffs Motor Mount
Steering Hardware Set Front Bumper Set Axle Housing Set; Rear Center
Transmission Housing Front Gear Box/Bulkhead HD Diff Housing & Internals: Baja
Rey Rear Driveshaft Set: Baja Rey Hex, Rotor, Caliper & Pin Set (4) Center
Transmission Gear Set 40T Ring & 14T Pinion Gear FR/RR Front Axle Set (2)
Center Drive Shaft Center Outdrive Set Front Outdrive Set Rear Axle Shaft Set
Open Rear Diff Gear Set
Shock Ends, Tops, Piston
FR/RR Shock Body & Collar Set FR/RR Shock Shaft Set & Hardware
FR/RR Shock Seal & Limiter Set
Front and Rear Spring Set
Shock Tower, Upper/Track Rod Mounts, Rear
LOS234003 Trailing Arm, Steering, Upper, Drag Link St
LOS234004
LOS234005 LOS234006 LOS234007 LOS234008 LOS235001 LOS235002 LOS235003
LOS235004 LOS235005
Front Suspension Arm Set Upper/Lower
Steering Spindle Set & Hardware Front & Rear Sway Bar Links Front Hinge Pins &
Brace Set 7mm Steel Pivot Ball Double Boss (10) Cap Head Screws M2 x 6mm (10)
Cap Head Screws M2.5 x 10mm (10) Cap Head Screws M3 x 6mm (10) Cap Head Screws
M3 x 25mm (10) Button Head Screws M2.5x6mm (10)
Deutsch Fuze 130A Sensorless Brushless ESC spritzwassergeschützt Fuze 550BL
Motor, 3800Kv Ritzel Modul 1, 13T Madenschrauben 4 & 5 mm (je 6) Kugelllager,
gekapselt 5 x10mm Kugelllager, gekapselt 6 x12mm (4) Kugelllager gekapselt 12
x18x 4mm Kugellager 5 x 10 x 4mm (2) Kugelllager, 3x6x2.5mm (2) Montiertes
Alpin-Rad und Reifen (2) Überrollbügelteile links und rechts
Obere Abdeckung, X-Abdeckung
Karosserieteil hinten Stoßfänger
Body Button Base & Top (22) Interiorset mit Helmen, transparent King Shocks
Raptor-Karosseriesatz Black Rhino Raptor-Karosseriesatz Ford Raptor Body
Karosserie-Adapterset Rote LED-Leuchtbalken, hinten Lüfterpanel, Schmutzfänger
Akkuhalter und Klappe, 2S Distanzstück
Stoßdämpferbefestigung hinten mit Chassishalter
Servohalter
Chassisplatte und Motorabdeckung Chassishalter und Distanzstücke Motorhalter
Zubehörset Lenkung Stoßstangensatz, Front Achsgehäuseset hinten Achsgehäuse
mitte Getriebegehäuse mit Halter Differentialgehäuse mit Einsätzen
Antriebswelle hinten Scheibenbremse mit Bremssattel Vorne/Hinten Getriebeset
Mitte Stirnrad 40 Zähne & 14 er Ritzel Vorderachsenset (2) Antriebswelle Mitte
Antriebsklaue mitte Antriebsklaue vorne Hinterachsewellenset Offenes
Heckdifferential Getriebesatz
Stoßdämpferendteile, Kolben
Stoßdämpfergehäuse, Distanzringe v/h Dämpfer Kolbenstange mit Zubehör
Stoßdämpferdichtung und Begrenzer
Dämpferfedern v/h
Dämpferbrücke hinten
Lenkgestänge
Querlenkenkerset unten
Lenkspindelset: Baja Rey Querlenkerverbinder vorne Qiuerlenkerstifte und
Halter 7mm Kugelköpfe (10) Sechskantschraube M2 x 6mm (10) Sechskantschraube
M2.5 x 10mm (10) Sechskantschraube M3 x 6mm (10) Sechskantschraube M3 x 25mm
(10) Halbrundschraube M2.5 x 6mm (10)
Français
Contrôleur Fuze Brushless 130A étanche
Moteur Fuze Brushless 550, 3800Kv Pignon modulaire 1.0, 13 dents Vis, 4mm et
5mm (6 chacun) Roulements à billes scellés 5x10mm (2) Roulements à billes
scellés 6x12mm (4) Roulements à billes scellés 12x18x4mm (2) Roulements 5 x 10
x 4mm (2) Roulements à billes 3x6x2.5mm (2) Support volant et pneu alpin (2)
Faces latérales gauche et droite de l’arceau cage
Barre supérieure, Barre X, protection et support pneu
Barre avant, barre de support de carrosserie arrière, support Anneaux de
protection de carrosserie (22) Décoration intérieure avec casques,
transparente Ensemble de carrosserie King Shocks Raptor Ensemble de
carrosserie Black Rhino Raptor Ensemble d’adaptateur de carrosserie Ford
Raptor Barre d’éclairage à DEL arrière rouge Cloison arrière, ventilateur et
bavettes
Support batterie, trappe, verrou et cales 2S
Triangle supérieur/fixation d’amortisseur avant, renfort arrière de châssis
Support servo, servo de direction plastique
Platine de châssis et couvercle moteur Renfort central de châssis et
entretoises Support moteur Set d’accessoires de direction Jeu de pare-chocs
avant Carter de pont arrière Boitier de transmission centrale Set de carters
de transmission avant/Cellule Corps de différentiel renforcé et éléments
internes Tiges de cardans arrière Hexagone, rotor, mâchoires et goupilles Set
de pignons de transmission centrale Anneau 40T et Pignon 14T avant/arrière Axe
de roues avant (2) Cardan central Set de noix de cardans centraux Set de noix
de cardans avant Axe de roues arrière Ensemble d’engrenage différentiel
arrière ouvert Chapes d’amortisseurs, bouchons supérieurs et pistons Corps
d’amortisseurs avant/arrière avec bague Tiges d’amortisseurs avant/arrière
avec visserie
Joint d’amortisseurs avant/arrière avec limiteur
Ressort avant/arrière
Support d’amortisseurs, tirants
Tringlerie de direction supérieure
Bras de suspension avant supérieur et inférieur
Set de fusées et visserie Tringlerie barre anti-roulis avant/arrière Renfort
de cellule avant Rotules Double Boss acier 7mm (10) Vis CHC M2 x 6mm (10) Vis
CHC M2,5 x 10mm (10) Vis CHC M3 x 6mm (10) Vis CHC M3 x 25mm (10) Vis BHC M2,5
x 6mm (10)
Italiano
ESC brushless waterproof Fuze 130 A senza sensori Motore brushless Fuze 550,
3800 Kv Pignone a passo modulare 1.0, 13 denti Grani, 4 mm e 5 mm (6 cad.)
Cuscinetto a sfere sigillato 5×10 mm (2) Cuscinetto a sfere sigillato 6×12 mm
(4) Cuscinetto a sfere sigillato 12x18x4 mm (2) 10x15x4mm Cuscinetti 5 x 10 x
4mm (2) Cuscinetto a sfere 3x6x2,5 mm (2) Ruota alpina con pneumatico montato
(2) Parti laterali roll cage D&S Barra superiore, barra a X, copertura e
supporto gomma Barra ant., barra supporto carrozz. post., paraurto, montante
torretta Body Button Base & Top (22): Baja Rey Set interni con caschi,
trasparente Set carrozzeria King Shocks Raptor Set carrozzeria Black Rhino
Raptor Set adattatore carrozzeria Ford Raptor Barra a LED rossa posteriore
Paratia post., fan panel, parafango Vano batteria, portello, chiusura,
distanziale 2S Braccetto superiore ant. / supporto ammortizz., trapezio post.
Supporto servo, set servo sterzo in plastica Piastra telaio & piastra
copertura motore Montanti telaio centrali con distanziali Supporto motore Set
hardware sterzo Set ammortizzatore anteriore Set alloggiamento asse posteriore
Scatola trasmissione centrale Scatola ingranaggio anteriore / paratia Scatola
diff. HD ed parti interne Set trasmissione posteriore Set esagone, rotore,
spessore e perno Set ingranaggio trasmissione centrale 40T ingranaggio & 14T
pignone ant./post. Set asse anteriore Albero di trasmissione centrale Set
trascintore centrale Set trascintore anteriore Set semiasse posteriore Set
ingranaggio differenziale posteriore aperto
Terminali, tappi, pistoni ammortizz.
Corpo ammortizz. ant./post & collarino Stelo ammortizz. ant./post e hardware
Set guarnizione ammortizz. ant./post. e limitatore Set molle ant./post.
Torretta ammortizz., supporti tirante sterzo superiore post. Braccetto
longitudinale, sterzo, superiore, tirante sterzo Set braccetti sospensione
ant. inferiore/ superiore Set fusello sterzo e hardware: Collegamenti barra
antitorsione ant./post. Perni braccetti ant. e set piastrine 7mm Steel Pivot
Ball Double Boss (10) Viti a testa piatta M2 x 6mm (10) Viti a testa piatta
M2.5 x 10mm (10) Viti a testa piatta M3 x 6mm (10) Viti a testa piatta M3 x
25mm (10) Viti a testa tonda M2.5x6mm (10)
FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · MANUALE DI ISTRUZIONI
35
IT
Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi
Part # LOS235006 LOS235007 LOS235008 LOS235009 LOS235010 LOS235011 LOS235012 LOS235013 LOS235014
English Button Head Screws M2.5x 20mm (10) Button Head Screws M4 x 12mm (10) Flat Head Screws M2.5 x 5mm (10) Flat Head Screws M2.5 x 8mm (10) Flat Head Screws M2.5 x 12mm (10) Set Screw, M3 x 3mm Cup Point (10) Set Screw, M4 x 4mm Cup Point (10) Flat Nut, M3 x 0.5 x 5mm (10) Lock Nut, M2 x 0.4 x4mm (10)
Deutsch Halbrundschraube M2.5 x 20mm (10) Halbrundschraube M4 x 12mm (10) Flachkopfschraube M2.5 x 5mm (10) Flachkopfschraube M2.5 x 8mm (10) Flachkopfschraube M2.5 x 12mm (10) Madenschraube M3 x 3mm spitz (10) Madenschraube, M4 x 4mm spitz (10) Flachmutter M3 x 05 x 5mm (10) Stoppmutter M2 x 0.4mm (10)
Français Vis BHC M2,5 x 20mm (10) Vis BHC M4 x 12mm (10) Vis FHC M2,5 x 5mm (10) Vis FHC M2,5 x 8mm (10) Vis FHC M2,5 x 12mm (10) Vis STHC M3 x 3mm CUV (10) Vis STHC M4 x 4mm CUV (10) Écrou plat M3 x 0,5 x 5mm (10) Écrou auto- freiné M2 x 0,4 x 4mm (10)
LOS235015 Lock Nut, Flanged M5 x 0.8 (10)
Stoppmutter M5 x 0.8mm geriffelt (10)
Écrou auto-freiné épaulé strié M5 x 0,8mm (10)
LOS236002 SPM2335
Differential Shim Kit DX2E 2.4 GHz Transmitter
Differential keil Kit Spektrum DX2E 2.4GHz Fernsteuerung
Kit de cale différentielle Émetteur Spektrum 2,4GHz DX2E
SPMS605
9KG Servo, WP, Metal Gear, 23T
Servo, spritzwassergeschützt 9Kg MG, 23T
Servo 9Kg à pignons métal, étanche, tête 23T
SPMSRS6000 Spektrum SRS6000 DSMR AVC Surface Receiver
TLR5904 TLR5909 TLR5910 TLR5911 TLR5913 TLR5932 TLR5933 TLR5934 TLR5935 TLR5961 TLR5963 TLR5964 TLR5965 TLR6312 TLR6313 TLR6352 TLR74006 TLR255007 VTR236003 VTR236025 VTR246001
Button Head Screws, M3 x 0.5mm x 12mm, Stl, BZ Button Head Screws, M3 x 0.5mm x 16mm, Stl, BZ, Pref Button Head Screws, M3 x 0.5mm x 14mm, Stl, BZ Button Head Screws, M3 x 0.5mm x 20mm, Stl, BZ, Pref Button Head Screws, M2.5 x 0.45mm x 12mm, Stl, BZ Cap Head Screws, M3 x 0.5mm x 10mm, Stl, BZ, Pref Cap Head Screws, M3 x 12mm (10) Cap Head Screws, M3 x 0.5mm x 16mm, Stl, BZ, Pref Cap Head Screws, M3 x 0.5mm x 20mm, Stl, BZ, Pref Screw, M3 x 0.5mm x 8mm, Flat Head, Stl, BZ Screw, M3 x 0.5mm x 12mm, Flat Head, Stl, BZ Screw, M3 x 0.5mm x 16mm, Flat Head, Stl, BZ, Pref Screw, M3 x 0.5mm x 20mm, Flat Head, Stl, BZ, Pref Locknut, M2.5x.45 x 5mm (6) Nut, M3 x 0.5mm x 5.5mm, Nylock, Stl, Clear Zinc Washer, 3.2mm x 7mm x 0.5mm, Stl, Clear Zinc Silicone Shock Oil, 30wt, 2oz. Button Head Screws M4 x .07mm x 12mm (10) Flat Nut, M4 x 0.7 x 7mm (10) M4 Nylock Flanged Nut Screw Pin, Clip Post (10): Glamis Uno
Spektrum SRS6000 DSMR AVC Surface Empfänger TLR Rundkopfschraube, M3 x 12mm (10) TLR Rundkopfschraube, M3 x 16mm (10) TLR Rundkopfschrauben, M3 x 14mm (10 TLR Rundkopfschrauben, M3 x 20mm (10) TLR Rundkopfschrauben, M2.5 x 12mm (10) TLR Zylinderkopfschraube, M3 x 10mm (10) TLR Zylinderkopfschraube, M3 x 12mm (10) TLR Zylinderkopfschraube, M3 x 16mm (10) TLR Zylinderkopfschraube, M3 x 20mm (10) TLR Flachkopfschrauben, M3 x 8mm (10) TLR Flachkopfschrauben, M3 x 12mm (10) TLR Flachkopfschrauben, M3 x 16mm (10) TLR Flachkopfschrauben, M3 x 20mm (10) Stopmutter M2.5 x .45 x 5mm (6) TLR Mutter selbstsichernd, M3 x .5 x 5.5mm (10) TLR U-Scheibe, M3 (10) Silikon Dämpferöl 30wt, 2oz TLR Rundkopfschraube, M4 x 12mm (10) Flachmutter M 4 x 0,7 x 7mm (10) Nylon Bundmutter M4 Stiftschraube (10) GLU
Récepteur SRS6000 avec Technology AVC
Vis à tête bombée M3 x 12mm (10) Vis à tête bombée M3 x 16mm (10) Vis à tête
bombée M3 x 14mm (10) Vis à tête bombée M3 x 20mm (10) Vis à tête bombée M2.5
x 12mm (10) Vis BTR M3 x 10mm (10) Vis BTR M3 x 12mm (10) Vis BTR M3 x 16mm
(10) Vis BTR M3 x 20mm (10) Vis à tête fraisée M3 x 8mm (10) Vis à tête
fraisée M3 x 12mm (10) Vis à tête fraisée M3 x 16mm (10) Vis à tête fraisée M3
x 20mm (10) Ecrou M2,5×0,45x5mm (6) Ecrou M3 x 0,5 x 5,5mm (10) Rondelles M3
(10) Huile silicone d’amortisseur, 30wt, 60 ml Vis à tête bombée M4 x 12mm
(10) Écrou plat, M4 x 0,7 x 7mm (10) Ecrou épaulé autofreiné M4 (10) Supports
de clips avec goupilles (10): GLU
Optional Parts // Diverse Teile // Pièces optionnelles // Pezzi opzionali
Part # LOS43006 LOS43011 LOS230009 LOS230026 LOS232011 LOS321009 LOS330001 LOS330005 LOS331001 LOS331002 LOS331003
English Wheels (4) Desert Claws Tires Soft w/Foam (2) Body Set, Clear Sticker Sheet Rear Diff Locker Front Bumper & Skid Plate: Baja Rey LED Roof Light Bar Set Body Set, Clear Aluminum Steering Servo Mount Aluminum Bellcrank Servo Saver Set Adjustable Turnbuckle Set
Deutsch Räder (4) Desert Claws Reifen mit Schaumeinlage (2) Karosserie Set Sticker Bogen Differentialsperre hinten Stoßfänger vorne und Unterfahrschutz LED Light Bar Set f. Dachmontage Karosserie Set Lenkservohalter Alumimium Servo Saver Aluminum Gewindestangenset einstellbar
Français Roues (4) Pneus Desert Claws Soft avec inserts (2) Carrosserie, transparente Feuille d’autocollants Verrou de diff arrière Pare choc avant et protection Rampe lumineuse DEL toit Carrosserie, transparente Support de servo de direction aluminium Sauve servo levier aluminium Biellettes réglables
LOS331004 Aluminum Rear Upper Link & Space Set
Heckanlenkung und Distanzstück Aluminium
Tirant supérieur arrière et entretoise aluminium
LOS331005 LOS331006 LOS331007
LOS332001
LOS332003 LOS334001
LOS334002
Aluminum Servo Arm, 23T Aluminum Servo Arm, 24T Aluminum Servo Arm, 25T
Al Lightened Hex Adapter Set, 12mm x 6mm
Lightened Front Outdrive Set Aluminum Front Spindle Set
AL Axle Housing Upper Track Rod Mount
LOS334003 Aluminun Upper Lower Buklhead Track Rod Mounts
Servoarm Aluminium, 23T Servoarm, Aluminium 24T Servoarm Aluminium, 25T
Radmitnehmer Set ultraleicht Aluminium 12 x 6mm: Baja Rey Frontabtriebset
ultraleicht Radträger Set Aluminium
Achsgehäuse oben Aluminium
Achsgehäuse Aluminium unten
Palonnier de servo aluminium, 23T Palonnier de servo aluminium, 24T Palonnier
de servo aluminium, 25T
Hexagones aluminium allégé, 12mm x 6mm
Set de noix de cardans avant allégées Fusées avant aluminium Carter de pont
supérieur aluminium Track Rod Mount Cellule supérieure/inférieure aluminium
Track Rod Mount
LOS334004 Aluminum Rear Shock Tower Set
Dämpferbrückenset Aluminium hinten
Supports d’amortisseurs arrière aluminium
LOS334005 Aluminum Front Shock Tower
Dämpferbrückenset Aluminium vorne
Supports d’amortisseurs avant aluminium
LOS334006 Aluminum Lower Rear Trailing Arm Set
Spurstangenset unten Aluminium:
Bras arrière inférieur aluminium
Italiano
Viti a testa tonda M2.5x 20mm (10) Viti a testa tonda M4 x 12mm (10) Viti a
testa piatta M2.5 x 5mm (10) Viti a testa piatta M2.5 x 8mm (10) Viti a testa
piatta M2.5 x 12mm (10) Grano, M3 x 3mm punta piana (10) Grano, M4 x 4mm punta
piana (10) Dado piatto, M3 x 0.5 x 5mm (10) Dado autobloccante, M2 x 0.4 x4mm
(10) Dado autobloccante con flangia dentata M5 x 0.8 (10) Kit di zeppa
differenziale Spektrum DX2E trasmittente 2,4 GHz Servo 9 kg, waterproof,
ingranaggi metallici, 23 denti Ricevente di superficie Spektrum SRS6000 DSMR
AVC Viti testa tonda,M3 x 12mm (10) Viti testa tonda, M3 x 16mm (10) Viti
testa tonda, M3 x 14mm (10) Viti testa tonda, M3 x 20mm (10) Viti testa tonda,
M2.5 x 12mm (10) Viti testa a brugola, M3 x 10mm (10) Viti testa a brugola, M3
x 12mm (10) Viti testa a brugola, M3 x 16mm (10) Viti testa a brugola, M3 x
20mm (10) Vite a testa piatta, M3 x 8mm (10) Vite a testa piatta, M3 x 12mm
(10) Vite a testa piatta, M3 x 16mm (10) Vite a testa piatta, M3 x 20mm (10)
Dado autobloccante, M2,5 x 45 x 5 mm (6) Dado autobloccante, M3 x .5 x 5.5mm
(10) Rondelle, M3 (10) Olio siliconico ammortizzatori, 30 wt, 2 oz. Viti testa
tonda, M4 x 12mm (10) Dado piatto, M4 x 0,7 x 7mm (10) Dado flangiato Nylock
M4 Perni viti clip (10): GLU
Italiano Ruote (4) Gomme Desert Claws soft con inserti (2) Set carrozzeria,
trasparente Adesivi Diff. locker posteriore Paraurto anteriore e piastra
proteggi telaio Set barra luci LED tetto Set carrozzeria, trasparente Supporto
servo sterzo alluminio Set salvaservo squadrette alluminio Set tiranti
filettati regolabili Set collegamenti e distanziali superiori posteriori
alluminio Squadretta servo alluminio, 23 denti Squadretta servo alluminio, 24
denti Squadretta servo alluminio, 25 denti Set adattatore esagoni alluminio
alleggerito, 12 mm x 6 mm Set trascinatore anteriore alleggerito Set fusello
anteriore alluminio Supporto tirante trasversale superiore corpo asse
alluminio Supporti tiranti trasversali paratia inferiore superiore alluminio
Set torre ammortizzatore posteriore alluminio Torre ammortizzatore anteriore
alluminio Set braccio longitudinale posteriore inferiore alluminio
36
FORD® RAPTOR BAJA REY®: F1O:1R0D4®WRDAPRTTORR·BMAJAANRUEAYL®E: D1:I1I0ST4RWUDZIORTNRI
IT
EXPLODED VIEW EXPLOSIONSZEICHNUNG VUE ÉCLATÉE DES PIÈCES VISTA ESPLOSA DELLE
PARTI
LOS230068
VTR236003
LOS230011
LOS43025
LOS231058
LOS235011 LOS234007 LOS234007
TLR5935 LOS235013 TLR6313
TLR5933 TLR5935 LOS231007
LOS234007 TLR5904
LOS234007 LOS235011
LOS234006 LOS231058
LOS235006
TLR5913
LOS235006
TLR5913
TLR5913
LOS230011 TLR255007
LOS230011
LOS230011
VTR236003
TLR5913
TLR5913
LOS230012
LOS230011
LOS230011
LOS230010
TLR5913
LOS235005
TLR5913 LOS230012
TLR5910
TLR5910
LOS230011 TLR5913
LOS230010
LOS235005 TLR5913
LOS235006
LOS230012 TLR5913
LOS235006
TLR5913 TLR5913
TLR5913
TLR5913
FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · MANUALE DI ISTRUZIONI
37
FORD® RAPTOR BAJA REY®:F1O:1R0D4®WRADPRTTORR·BMAJAANRUEAYL®E: 1D:I1I0ST4RWUDZIROTNRI
38
EXPLODED VIEW EXPLOSIONSZEICHNUNG VUE ÉCLATÉE DES PIÈCES VISTA ESPLOSA DELLE
PARTI
LOS230013
LOS230066 or LOS230067 or LOS330005
LOS231005
LOS230066 or LOS230067 or LOS330005
LOS230020
LOS230069
LOS230020
LOS230066 or LOS230067 or LOS330005
LOS231005
LOS230066 or LOS230067 or LOS330005
LOS43025 LOS235015
IT
EXPLODED VIEW EXPLOSIONSZEICHNUNG VUE ÉCLATÉE DES PIÈCES VISTA ESPLOSA DELLE PARTI
LOS232002
LOS232007
LOS232007 LOSA6250
LOS235003 LOS232002
LOSA6937 LOSA3573
LOSA6937
LOS231012 DYNS1616
TLR6313
LOS232012 LOS232004
LOSA6956 LOS232007
LOSA6956 LOS232012
LOS232004
TLR5909
TLR5904 TLR6352 DYN4955
IT
SPMSRS6000 TLR5904 TLR6352
TLR5910
TLR5904
LOS232003
LOS232013 LOSA6957
LOS236002 10x15x0.2mm
LOS232008 LOS232051
LOS236002 5x12x0.4mm
TLR5910
TLR5904
LOS232003
VTR246001
LOSA6937
LOS236002 5x7x0.1mm LOS232008
LOS232012 LOS236002 5x7x0.2mm
SPMS605
LOS232010
LOS234008
LOS233001 LOS233004
LOS233001
LOS233004 LOS233001 LOS233002
TLR6312 LOS233003
LOS233001 LOS233004
LOS233005
LOS233002
LOS233001
LOS233003
LOS236002 5x12x0.4mm
LOSA6957 LOS232013
LOS234004
LOS233001
LOS234004
LOS234005
LOS234008
LOS233001
LOS232009 LOS235008
TLR5911
LOS234004
LOS234003
TLR5911 LOS234008
LOS234005
LOS235001 LOSA6940 LOS232009
LOS232006
LOS234004
LOS234004
LOS235001
LOS234005
VTR246001
LOS232006
LOS232006
LOS234005
FORD®® RAPTOR BAJA REY®®: 1:10 4WD RTR · MANUALE DI ISTRUZIONI
39
IT
CHASSIS EXPLODED VIEW CHASSIS EXPLOSIONSZEICHNUNG VUE ÉCLATÉE DU CHÂSSIS VISTA
ESPLOSA DEL TELAIO
LOS231008
LOSB3008 VTR236025
LOS231008
LOS231013
LOS231013
LOSB3008 LOS231013
LOS234003
LOSB3008
LOS231008 TLR6313
LOS231013
LOS231013
LOSB3008 TLR6313
LOS231008 TLR5910
LOS231013
LOS231008
TLR6313
LOS231008
LOS234008 TLR6352
TLR5910 TLR6313
TLR5910 LOS234007
LOS235005
LOS231008
LOS234008
TLR6352
TLR5910
LOS235006
LOS230012 TLR5911
TLR5913 LOS231005
LOS234002
LOS235011 LOS235009
TLR6313
TLR5913 LOS231005
LOS235002 LOS234002 TLR5904
TLR5911 LOS235011
LOS235009 LOS231005
TLR6352 LOS231008
TLR5910 TLR6352
TLR5961
LOS231006 TLR5935
LOS234002
LOS234006 LOS234006
TLR5909
LOS234006
TLR5965
TLR5911
LOS235004
TLR6313
LOS234002
TLR6313
TLR6313 LOS234006
TLR5965
TLR5963 LOS234002
TLR6313 LOS234006
LOS234006
TLR6313 LOS234006
LOS234006
LOS231007
TLR6313
TLR5909
LOS230012
LOS234002
TLR6313 TLR5911
LOS235006
TLR5965
TLR5911
LOS235002
LOS231006
TLR5904 LOS235011
TLR5911 LOS234002
TLR5965
LOS231011
LOS231011
TLR5961
LOS231011
LOS235009
LOS231010 TLR5963
TLR5963
TLR5935 TLR5961 LOS235009
TLR5963 LOS231006
LOS231010
TLR5963
40
FORD® RAPTOR BAJA REY®:F1O:1R0D4®WRADPRTTORR·BMAJAANRUEAYL®E: 1D:I1I0ST4RWUDZIROTNRI
FORD®® RAPTOR BAJA REY®®: 1:10 4WD RTR · MANUALE DI ISTRUZIONI
REAR EXPLODED VIEW HECK EXPLOSIONSZEICHNUNG VUE ÉCLATÉE ARRIÈRE VISTA ESPLOSA DELLA PARTE POSTERIORE
LOS234008 LOS233001 LOS233002
LOS233001
LOS233001 LOS233004
LOS233004
LOS233002
LOS232006
TLR6312 LOS233001
LOS233003
LOS233005
VTR246001
LOS232006
LOS232014
LOS235001 LOSA6940
TLR5964
LOSA6940
LOS232001
LOS232014
LOS233003
LOS233004 LOS233001
LOS234008 LOS234008
LOS232005
LOS232014
TLR5911
LOS234008
TLR6313 LOS234003
LOS234003
LOSA6957
TLR5934
LOS232051
LOS236002 5x17x0.4mm
LOS232008 LOS236002 5x7x0.1mm
LOS236002 5x17x0.4mm
LOS236002 5x7x0.2mm LOSA6937
LOSA6937
TLR5934
LOS232001
TLR5911 LOS234008 LOS232001
TLR6313
TLR5909 LOS234008
TLR5911
TLR5904
LOS232001
LOS236002 10x15x0.2mm
LOSA6957
LOS232014
LOS234003 LOS234008
TLR6313 LOS234008 TLR5911
LOS234003
LOS233004 TLR6313
LOS232014
LOSA6940
LOS235001
LOSA6940
LOS232006
LOS232001 TLR5964 LOS232014
VTR246001
LOS232006
LOS233001
LOS233001 TLR5911
LOS234008
LOS234008
41
IT
WWW.LOSI.COM
©2020 Horizon Hobby, LLC.
Losi, Baja Rey, DSM, DSM2, DSMR, AVC, Active Vehicle Control, EC3, Dynamite, Fuze, Prophet and the Horizon Hobby logo are trademarks
or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used
with permission of Bachmann Industries, Inc.
®
Ford Motor Company Trademarks and Trade Dress are used under license to
Horizon Hobby.
US 9,320,977,US 10,528,060. US 9,930,567. US 10,419,970. Other patents pending.
Updated 5/20
57527.1 | LOS03020T1/T2
References
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
- Horizon Hobby Service Center
- Horizon Hobby Service Center
- RC Cars, RC Trucks, RC Airplanes, Model Trains, and Slot Cars at Tower Hobbies
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
- RC Airplanes and Helicopters, RC Cars and Trucks, RC Boats, RC Radios | Horizon Hobby
- Horizon Hobby Service Center
- The leaders in RC car and truck innovation and design | Losi
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>