Midea Window Type Air Conditioner Installation Guide

June 7, 2024
Midea

Midea logo

Window Type Air Conditioner

Models
MAW08V1QWT
MAW10V1QWT
MAW12V1QWT

version A – 03 – 2020

Midea Window Type Air Conditioner

Installation Guide

Scan the following QR code for an installation video.

Midea QR code A

You must follow the user manual for detailed installation instructions
Before using your air conditioner, please read the user manual carefully and keep for future reference. For additional support, please call customer service at 1-866-646-4332.

Page 1

TOOL & HARDWARE

Required Installation Hardware

| 1/2” Type B Screw| 2
---|---|---
| 1/4” Type B Screw| 2
Main Bracket| Main Bracket| 1
Right Extension Arm| Right Extension Arm (For 26”-36” windows)| 1
| Right Extension Arm – Short (For 22”-26” windows)| 1
| Main Support Pin| 2
| Cotter Pin| 2
| 1/2” Type A Screw| 3
| Open Window Bracket – RH| 1
| Open Window Bracket – LH| 1
| Side Arm Foam| 2

Optional Installation Hardware

| Window Sash Lock| 1
---|---|---
| Thick Window Sash Seal Foam| 1
| Thin Window Sash Seal Foam| 1
| Miscellaneous Sealing Foam| 1
| Additional Side Arm Foam| 2
| 1” Type A Screw| 2

WARNING
Do not use any devices or materials for installation that are not recommended in this manual.

WINDOW REQUIREMENTS

Wooden Windows 1Seal Form, OFFSET, EXTERIOR WALL, INNER WINDOW SILL, INTERIOR WALL, Wooden WindowsVinyl-Clad Windows 1Seal Form, OFFSET, EXTERIOR WALL, INNER WINDOW SILL, INTERIOR WALL, Vinyl-Clad WindowsWooden
Windows 2INSIDE, OUTSIDE, Wooden WindowsVinyl-Clad Windows
2INSIDE, OUTSIDE, Vinyl Lip, Vinyl-Clad Windows

NOTICE
Maximum window thickness including non-removable handle: 2-7/8″

Page 2

Midea logo


1. INSTALL THE SUPPORT BRACKET

WARNING

  • Bracket should only be used for its intended purpose. If not, the warranty will be voided.
  • You must follow the detailed installation instructions in the user manual.

INSTALL THE SUPPORT BRACKET 1Right, Left Extension Arm, Horizontal Bracket

1.1 Adjust the left extension arm out and install the right extension arm. Set the bracket in your window.

INSTALL THE SUPPORT BRACKET 1.1

WARNING
Maintain control of the bracket until installation is complete.

Depending on the level used, place at either location below to check level.

INSTALL THE SUPPORT BRACKET 2

1.2 Adjust the angled support arms until they touch the exterior wall. Check that the bracket is properly tilted downwards toward the outdoors. Install the support pins and cotter pins then extend the left and right extension arms.INSTALL THE SUPPORT BRACKET 1.2 Center this part of the bracket with the center of the windows., Extend the Extension Arms until they touch the Windowsill and the Spring Pin locks in place.INSTALL THE SUPPORT BRACKET 3Spring Pin LocksINSTALL THE SUPPORT BRACKET 4Spring Pin LocksINSTALL THE SUPPORT BRACKET 5Cotter Pin

Page 3                  Installation Guide

Midea logo


1. INSTALL THE SUPPORT BRACKET (cont.)

Use the provided 1/2″ Type A screws.

INSTALL THE SUPPORT BRACKET 1.3 A

NOTE: Drill 1/8″ pilot holes before screwing into the window sill.

1.3 Secure the bracket to the window with a screw at the end of each extension arm as shown. Holes at the end or bottom of the Extension Arms can be used to secure the Support Bracket to the window.

2. SECURE THE UNIT ON THE BRACKET

2.1 Set the air conditioner on the support bracket and fold down the side arm hinges.

WARNING
Do not leave the unit unattended during installation.

SECURE THE UNIT ON THE BRACKET 2.1

2.2 You must install the Open Window Brackets.

WARNING
Failing to do this could cause injury or property damage.SECURE THE UNIT ON
THE BRACKET 2.2Use the 1/4, 1/2″ Type B screw


Installation Guide                                  Page 4

3. SEAL AND CLOSE THE WINDOW

3.1 Measure, cut and install the side arm foam.

WARNING
Do not leave the unit unattended during installation.

SEAL AND CLOSE THE WINDOW 3.1

3.2 Secure the anti-tip brackets into the window track and then close the window.

Top view

Remove the factory installed 1/2″ screw and extend the Anti-Tip Brackets into the window track. Secure the Anti-Tip Brackets by re-using the factory installed 1/2″ screw. Failing to use this screw could damage the air conditioner.SEAL AND CLOSE THE WINDOW 3.2 ATop of Unit, Extend into Window Track

SEAL AND CLOSE THE WINDOW 3.2 BSEAL AND
CLOSE THE WINDOW 3.3Use the thick window sash seal foam to seal between the windows, Check for Gaps

WARNING
You must extend the Anti-Tip Brackets into the Window Track Opening. Failure to follow this warning may cause serious injury.

3.3 Use the included foam to seal any gaps between the window and the air conditioner.

Page 5

Midea logo


SEAL AND CLOSE THE WINDOW 3.4a

3.4 Extend both window locks located in the window slot. For additional security, install the window sash lock.

SEAL AND CLOSE THE WINDOW 3.4b

FAQ Why does the air conditioner not start?


– Wall plug disconnected. Push plug firmly into wall outlet.
– House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.
– Check if the light on the plug is on. If it is off, press the RESET button.
– Power is OFF. Turn power ON.

FAQ Why is there noise during cooling?


– It is normal to hear airflow, set to a slower fan setting if too loud.
– Window vibration – poor installation. Refer to installation instructions or check with installer.

FAQ Unit will not connect to Wifi or App does not work?


For additional support and troubleshooting tips, follow the link in this QR code.

Midea QR code B

Page 6                                               Installation Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals