MOULTRIE MFG-15075 Bluetooth Pro Feeder Kit Instruction Manual

MOULTRIE MFG-15075 Bluetooth Pro Feeder Kit

Product Instructions

Instructions for BLUETOOTH PRO FEEDER KIT

• Thank you for your purchase of a BLUETOOTH PRO FEEDER KIT Please read this sheet before operating the unit.
• If you should have any questions about this product or any other Moultrie product, please contact us using the information on the back of this sheet.
• Allow us to better serve you by activating your 1-year warranty online at http://www.moultriefeeders.com/warranty.

STOP: READ THIS FIRST BEFORE PROCEEDING

If mounting the Moultrie Quick Lock Feeder Kit to:

• a Moultrie 30 or 55-gallon barrel* or Moultrie 6.5-gallon bucket, refer to Section B.
• a Moultrie 30-gallon Quick-Lock Hopper, refer to Section C.
• any other containers, please visit our website at www.moultriefeeders.com.

To operate the Bluetooth Timer, refer to the Quick Start Guide in the packaging, or if you have any questions please visit our support page.

Product Using Instruction

• A DUSTING FUNNEL HEIGHT
  • To adjust funnel height:
  1. With a Phillips-head screwdriver, loosen the screw.
  2. With the screw loosened, use tabs to position the funnel in one of the two positions by either pushing down or up depending on the desired position.
  3. Once the funnel is in the desired position, retighten the screw with a Phillips-head screwdriver. Do not over-tighten.
• B ASSEMBLE WITH MOULTRIE QUICK-LOCK ADAPTER
  • **55-gallon or 30-gallon Barrel***
  1. Assemble the Quick-Lock adapter by snapping bolt tabs in place as shown.
  2. Turn the metal drum upside down slide the belly band ring around the perimeter and make sure that the belly band is snug against the bottom structure ring as shown (Moultrie barrel only).
  3. Slide the bolt through the belly band ring, spacer and lock washer as shown. Tighten the nut on the bolt until the metal belly band ring tabs are touching the spacer on each side.
  4. Mount Quick-Lock adapter using (3) 1/4″ x 1″ bolts, nuts and washers provided in the pre-drilled holes (Moultrie barrel only). Or use the Quick-Lock adapter as a template to mark and drill the mounting holes (non-Moultrie barrel).
  5. Connect the Quick-Lock feeder kit to the assembled adapter as shown.
  • Can also be used on a 6.5-gallon bucket.
• (C) ASSEMBLE MOULTRIE 30-GALLON QUICK-LOCK HOPPER

1. Place the hopper bottom flat on the ground, and slide the three provided angled leg brackets into the hopper as shown. Make sure to fully insert brackets as far as you can to ensure the strength of the feeder.
2. Insert two (2) leg sections into each of the square leg brackets. Tap leg sections into place to ensure tight fit. Flip hopper bottom assembly upside-down so that all three (3) legs are on the ground.
3. Align holes of the hopper top, then press the sides of the hopper bottom until it snaps snugly in place. Insert bolt through each hole, place lock washer on bolt and screw wingnut onto bolt until tight. Repeat for all 12 bolts.
  *  **Note:** Failure to properly secure two halves can result in leakage.
  * After completing the hopper assembly, install as many leg sections as are needed for your application.
4. Connect the Quick-Lock feeder kit to the assembled hopper as shown.
5. Fill with corn/feed. Do not exceed 200 lbs.
  * Install the lid by aligning handles with notches in the hopper top. Twist until the lid rests flush against the lid stop.
  * To install a Moultrie game camera or Feeder Power Panel (sold separately), thread included 1/4″-20 x 1″ Phillips-head bolt upward through the hole in the lid handle and tighten the bolt. The lid will hold up to 3 devices.
  * DO NOT EXCEED 200 LBS OF FEED
  * Our Service Department will gladly answer any questions you have. [www.moultriefeeders.com/support](http://www.moultriefeeders.com/support).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>