remock Biometric Keypad Touch Panel with Fingerprint Reader User Manual

: June 11, 2024
: remock

Table of Contents

Biometric keypad
INSTALLATION
SIMPLIFIED PROGRAMMING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Biometric Keypad
Touch Panel with Fingerprint Reader
User Manual remock Biometric Keypad Touch Panel with Fingerprint
Reader

Biometric keypad

Remock Code is a wireless panel consisting of a fingerprint reader, 125 KHz proximity card reader and touch keypad, fully compatible with Remock and Remock Pro invisible locks, and the Remock Magic motorized cylinder. Installation can be done with either hardware or 3M double-sided adhesive, both providing an easy way of installation. The rolling code encryption algorithm and split design ensure enhanced security. The device can store 1000 fingerprint/PIN/user card. Due to the low power consumption, the batteries have a maximum autonomy of approximately six months, based on 30 operations per day. It will warn of the need to change batteries intelligently if the battery is low.
Common features:

1000 fingerprint/PIN/Card users.
– 4 – 6 digits PIN, 125 KHz EM Card
– 433 MHz Rolling Code technology
– Communication distance: 30 m (Max.)
– Ultra low power consumption
– 3 pcs AAA batteries

INSTALLATION

Method 1: Double-sided 3M adhesive
The device kit includes a 3M double-sided adhesive that allows you to easily stick the device to a smooth surface (adhesion will reach its optimum after 24 hours from installation).
Method 2: Screws

Remove the rear cover
Drill 2 holes (A, C) in the wall for the wall plugs and another one (B) to pass the cable through.
Pass the cable through the hole in the wall and fix the cover on the wall with the 2 screws.
Close the reader on its cover with the screw located on the bottom side.

SIMPLIFIED PROGRAMMING

Simplified instruction

Function a escription Operation	Operation
Enter programming mode	(123456) #

(123456 is factory MASTER code)
Change MASTER Code
IMPORTANT: Please remember the New MASTER Code, as the default value cannot be reset if forgotten.| 0 (New Code) # (Repeat New Code) #
(Code: 6 digits)
Add fingerprint user| 1 (user ID)#(Put Fingerprint 3 times) #
Add user PIN| 1 (User ID) # (PIN) # or 1 (PIN) #
(PIN length: 4-6 digits)
Add user Card| 1 (Zoom in Card) #
Delete user| 2 (Fingerprint) # or
2 (user ID) #
2 (PIN) #
2 (Card) #
Exit programming mode| *
How to open the door
Fingerprint access| (Place Fingerprint)
PIN access| (PIN) #
Card Access| # (Zoom in Card)
Close immediately: Press “0 ton the device

Programming of the device with the Invisible Lock
Please kindly refer to the following steps to pair the device.

Enter programming mode
Remove the battery door of the invisible lock, Remock or Remock Pro, press the registration button (round black button located to the left of the batteries) with a thin rod, hold it for 3 seconds until you hear three beeps for the lock to enter programming mode.
Remock Code wireless panel programming
Press the “0” button and release it, then press and hold the “#” button for 2 seconds until the lock beeps and the wireless panel is successfully programmed with the lock.
Exit programming mode
To finish, press the enrollment button on the invisible lock again until you hear a beep, or wait for the enrollment period to end automatically (15 seconds). In either case you will hear a beep to terminate the programming.

Programming of the device with the Smart Lock
Please kindly refer to the following steps to pair the device.

Insert new controller from the motorized cylinder Remock MAGIC
If you touch the menu button in the upper right corner when the application is connected to the motorized cylinder as a master control, you will reach the configuration menu.
In the bottom bar, tap the third icon from the left (Users) and go to Enroll new controller, tap the green “+” button. After touching the button it will emit a long warning tone (5 seconds) and a short tone. After that tone, immediately proceed to the next section.
Programming of the Remock CODE wireless panel
Press the “0” button and release it, then press the “#” button and hold it for 2 seconds, if the match is successful, you will hear two tones from the cylinder and the wireless panel will be a new controller.