KRAMER VP-440X 4K Presentation Switcher Scaler User Guide

: June 8, 2024
: Kramer

Table of Contents

KRAMER VP-440X 4K Presentation Switcher Scaler
Specifications
Frequently Asked Questions (FAQ)
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KRAMER VP-440X 4K Presentation Switcher Scaler

This guide helps you install and use your VP-440X for the first time. Go to www.kramerav.com/downloads/VP-440X to download the latest user manual and check if firmware upgrades are available.

Step 1: Check what’s in the box

VP-440X 4K Presentation
Switcher Scaler
1 Quick start guide
1 Power adapter and cord 4 Rubber feet

Step 2: Get to know your VP-440X

KRAMER-VP-440X-4K-Presentation-Switcher-Scaler-fig-1

The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

#	Feature		Function
1	48 V (up) Slide Switch	Slide up (48V) to select a condenser-type

microphone; slide down to select a dynamic-type microphone (we recommend that you slide down if a microphone is not connected to

the VP-440X ).

2| MIC 6.3mm Jack| Connect to the microphone source.
3| Input Selector Buttons| HDMI IN| Press to select the HDMI input (from 1 to 4).
4| PC IN| Press to select the computer graphics input.
5| MENU Button| Displays the OSD menu.
6| Navigation Buttons| left| Press to decrease numerical values or select from several definitions. When not in the OSD menu, press to reduce the output volume.
up| Press to move up the menu list values.
right| Press to increase numerical values or select from several definitions. When not in the OSD menu, press to increase the output volume.
down| Press to move down the menu list.
ENTER| Press to accept changes and change the SETUP parameters.
7| RESET TO XGA/1080p Button| Press and hold for about 5 seconds to toggle the output resolution between XGA and 1080p, alternatively.
8| PANEL LOCK Button| Press and hold for about 5 seconds to lock/unlock the front panel buttons.

KRAMER-VP-440X-4K-Presentation-Switcher-Scaler-
fig-2

#	Feature
9	HDMI™ IN Connectors	Connect to an HDMI source (from 1 to 4).
10	PROG USB Type A Connector	Use to upgrade the firmware.
11	DATA (Tx, Rx, GND) Terminal Block Connectors	Connect to a PC to Extend

RS-232 signals via the HDBT OUT port, for example, to control peripheral devices that are connected to the HDBT RECEIVER (e.g. a projector connected to TP-780Rxr ) via a PC or a serial controller.
12| CONTROL (Tx, Rx, GND) Terminal Block Connector| Connect to a PC or serial controller to control the VP-440X or control the output display (configurable).
13| SELECT 7-pin Terminal Block Connector| HDMI 1 to HDMI 4 and PC: connect to contact closure switches (by momentary contact between the desired pin and G pin) to select an input.

REMOTE: momentarily connect the pin to G, or connect an occupancy detector to turn on/off the display (configurable for edge or for level triggering).

14| PC IN 15-pin HD Connector| Connect to the computer graphics source.
15| AUDIO INPUT

Unbalanced Stereo 3.5 Mini

Jack

Step 3: Install VP-440X
Install VP-440X using one of the following methods:

Attach the rubber feet and place the unit on a flat surface.
Mount the unit in a rack using the recommended rack adapter (see www.kramerav.com/product/VP-440X).
The maximum mounting height for the device is 2 meters.
Ensure that the environment (e.g., maximum ambient temperature & air flow) is compatible with the device.
Avoid uneven mechanical loading.
Appropriate consideration of equipment nameplate ratings should be used to avoid overloading of the circuits.
Reliable earthing of rack-mounted equipment should be maintained.
The maximum mounting height for the device is 2 meters.

Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VP- 440X. For best results, we recommend that you always use Kramer high- performance cables to connect AV equipment to VP-440X. KRAMER-VP-440X-4K-
Presentation-Switcher-Scaler-fig-3

For optimum range and performance use the recommended Kramer cables available at www.kramerav.com/product/VP-440X.

Step 5: Connect the power
Connect the power adapter to VP-440X and plug it into the mains electricity. Safety Instructions (See www.kramerav.com for updated safety information)

Caution

For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.
There are no operator-serviceable parts inside the unit.

Warning

Use only the power cord that is supplied with the unit.
Disconnect the power and unplug the unit from the wall before installing it.

Step 6: Operate and control the VP-440X

Operate VP-440X via:

Input select and MENU front panel buttons (as well as reset and panel lock buttons).
Remotely, by RS-232 serial commands transmitted by a touch screen system, PC, or other serial controller.
Embedded web pages via the Ethernet.

Select an input via

Front panel IN buttons.
OSD menu.
Contact closure terminal blocks to select an input remotely with the press of a button (HDMI 1 to HDMI 4, and PC).
Embedded web pages.

Press the MENU button to configure and control the device via the OSD menu

Set brightness, contrast, color, etc.
Select resolution and aspect ratio.
Select the input source, and manage the audio input & output volume.
Manage microphone settings and volume.
Define OSD display.
Configure HDCP behavior on input/output.
Set auto-switching type and lock mode.
Set Ethernet IP mode, IP address, TCP/UDP ports, etc.
Manage auto power down (Auto Sync Off).
Manage EDID.
View device information.
Reset to factory default parameters.
WWW.KRAMERAV.COM

Specifications

Model: VP-440X 4K Presentation Switcher Scaler
Power Adapter: 5V DC
Connectivity : HDMI, USB Type A, RJ-45, 15-pin HD Connector, 3.5mm Jacks
Control : RS-232, Terminal Block Connectors

Frequently Asked Questions (FAQ)

Q: How can I upgrade the firmware of the VP-440X?
A: You can upgrade the firmware by connecting a USB Type-A cable to the PROG USB Type-A Connector on the device.

Q: How do I toggle the output resolution between XGA and 1080p?
A: Press and hold the RESET TO XGA/1080p Button for about 5 seconds to switch between XGA and 1080p resolutions.