MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors User Manual

: June 7, 2024
: MEE

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors User Manual

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors User
Manual www.MEEaudio.com/M6PROBT

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - QR
Code HOW TO WEAR FIT VIDEO
Before first use, watch our fit video by visiting
MEEaudio.com/PROhelp or scanning the QR code:

IMPORTANT
Please read this quickstart guide in its entirety to ensure best fit and sound

PACKAGE CONTENTS

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - PACKAGE
CONTENTS

1. M6 PRO In-Ear Monitors
2. Protective carrying case
3. BTC2 Bluetooth audio adapter cable
4. ¼” adapter
5. Comply™ memory foam eartips
6. Silicone eartips (6 pairs)
7. Shirt clip
8. Stereo audio cable

SELECTING EARTIPS

Multiple sets of eartips are included to ensure you get the best fit with your headphones.

The correct eartips for your ear will allow the earpieces to fit flush, reduce outside noise, and provide good bass response.

Install eartips as shown. Make sure eartips are installed securely before use.

MEMORY FOAM EARTIPS

1. REPLACE EARPHONE TIPS WITH COMPLYTM TIPS

2. ROLL TIP INTO THIN, ROUND CYLINDER

3. GENTLY INSERT TIP INTO EAR

4. HOLD TIP IN PLACE UNTIL FULLY EXPANDED

FOR REPLACEMENT TIPS, GO TO COMPLYFOAM.COM. THE COMPLY™ EARTIPS INCLUDED WITH THE M6 PRO ARE THE T-200 MEDIUM.

CHARGING BLUETOOTH ADAPTER

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - CHARGING
BLUETOOTH ADAPTER

Connect the Micro-USB charging cable to any powered USB port and to the charging port of the BTC2.

The status indicator light will turn blue once the BTC2 is charged and ready for use.

Close the USB port cover completely after charging for maximum sweat resistance.

PAIRING BLUETOOTH ADAPTER

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - PAIRING
BLUETOOTH ADAPTER 1

Press and hold the Multifunction button for about 5 seconds until you hear the headset say “Pairing” and the light flashes red and blue.

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - PAIRING
BLUETOOTH ADAPTER 2

Open the Bluetooth menu on the device you wish to pair (usually located in Settings > Bluetooth). If needed, select “search for devices”, “add new device”, or “refresh”.

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - PAIRING
BLUETOOTH ADAPTER 3

Select “MEE audio BTC2” and allow pairing to complete. Use “0000” if a pin is required.

Visit the Bluetooth Support Page at MEEaudio.com/Bluetooth for additional Bluetooth pairing and setup information.

WEARING M6 PRO WITH BLUETOOTH ADAPTER

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - WEARING M6 PRO
WITH BLUETOOTH ADAPTER 1

Identify the right and left earpieces.

Place the cable behind your neck and route the earhooks over your ears.

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - WEARING M6 PRO
WITH BLUETOOTH ADAPTER 2

Place the earpieces in your ears.

Adjust each earpiece until it fits flush in your ear and the eartip seals the ear canal.

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - WEARING M6 PRO
WITH BLUETOOTH ADAPTER 3

Tighten the sliding cable cinch for the most secure fit.

BASIC FUNCTIONALITY AND CONTROLS

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - BASIC
FUNCTIONALITY AND CONTROLS

You may need to bring your music player application up on the screen for media playback to start
** Not all devices support this functionality

DYNAMIC AUDIO ENHANCEMENT

The BTC2 features on-the-fly audio adjustment with three audio modes:

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - DYNAMIC AUDIO
ENHANCEMENT

FACTORY RESET

To perform a full reset, first put the BTC2 in standby mode (headset is powered on but not connected to any devices). Make sure to turn off Bluetooth or delete the “MEE audio BTC2” pairing from any nearby devices that have previously been paired with the BTC2.

Once in standby mode, press and hold the Multifunction and volume up buttons simultaneously until you hear the headset say “Factory Reset Complete”. All previously paired devices will be cleared from memory and a new pairing will need to be created before the BTC2 can be used.

REPLACING THE CABLE

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - REPLACING THE
CABLE 1

The M6 PRO includes two detachable, interchangeable cables a BTC2 Bluetooth audio adapter cable and a stereo audio cable.

Additional cable types, replacement parts, and other accessories are available at www.MEEaudio.com

To detach the cable, grasp the earpiece and cable connector firmly, and pull straight apart without twisting.

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - REPLACING THE
CABLE 2

Attach new cable by lining up the notches on the connectors with the grooves in the earpieces as shown. Push connectors in until they fit securely.

Make sure to attach the cable connector marked “R” to the right earpiece and the connector marked “L” to the left earpiece.

WEARING THE M6 PRO WITH STEREO CABLE

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - WEARING THE M6
PRO WITH STEREO CABLE 1

Identify the right and left earpieces.

Straighten the memory wire and put each earpiece in the corresponding ear.

Adjust each earpiece until it fits flush in your ear and the eartip seals the ear canal.

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - WEARING THE M6
PRO WITH STEREO CABLE 2

Holding the earpiece in place, bend the memory wire around your ear to achieve a conforming fit.

While pulling the cable gently with one hand, squeeze the memory wire behind your ear with the other hand until the fit is tight and secure.

MEE Universal-Fit Noise-Isolating Musicians In-Ear Monitors - WEARING THE M6
PRO WITH STEREO CABLE 3

Tighten the sliding cable cinch for the most secure fit.

Use the shirt clip to control cable movement.

ADDITIONAL INFORMATION

WARNINGS

Using headphones at high to moderate volumes for extended periods of time will result in permanent hearing damage. It is advised you keep volume levels moderate to low at all times for your safety. Do not use while driving a car, cycling, operating machinery, or performing other activities that require hearing surrounding sounds.

Keep the device and packaging out of reach of children.

This device is designed and manufactured to operate within its defined design limits. Misuse may result in electric shock or fire. Read and follow these instructions carefully.

To prevent fire or shock hazards, do not expose this unit to rain or moisture.
Danger of explosion or fire if batteries are damaged. Keep away from direct sunlight, naked flames, flammable gasses, or heat sources such as radiators or stoves
Only use attachments/accessories specified by the manufacturer

Changes or modifications to this unit not expressly approved by MEE audio could void the user’s authority to operate the equipment.

COMPLIANCE INFORMATION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC RULES

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

DISPOSAL AND RECYCLING

Dispose of this product in accordance with all local laws and regulations. Because this product contains electronic components and a battery, it must be disposed of separately from household waste. Contact local authorities to learn about disposal and recycling options.

WARRANTY

MEE audio products purchased from authorized resellers are covered by a 1-year manufacturer warranty. For more information, visit MEEaudio.com/Support.

FOR ADDITIONAL SUPPORT

Visit our Bluetooth Support Guide at MEEaudio.com/Bluetooth for easy-to-follow video setup guides and the latest troubleshooting information
Contact us at support@MEEaudio.com.

POWERED BY

MEE audio and its logo are registered trademarks of S2E, Inc.
MEE Professional and its logo are trademarks of S2E, Inc. All rights reserved.

Siri® is a registered trademark of Apple Inc.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MEE audio is under license. Other trademarks and trade names are those of their respective owners. Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.

Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries.

QUESTIONS?
WE’RE HERE TO HELP!

Phone Support: 626-965-1008
Monday ~ Friday 9 am to 5 pm PST

Email Support: support@MEEaudio.com
All emails are responded to within 2 business days

LIFETIME REPLACEMENT

Things don’t always go according to plan in the real world. Whether your headphones get crushed, shredded, fried, misplaced, or carried off by army ants, we’ve got you covered. Just tell us what happened and we’ll give you a new pair at half price, no questions asked (note: we reserve the right to ask for more of a great story).

Visit www.MEEaudio.com/LRP for more information or to request a replacement.