soundcore Soundbar Infini Mini User Manual

Soundcore Infini Mini
User’s manual

safety instructions

• Avoid dropping.
• Do not disassemble.
• Do not submerge in water.
• Avoid extreme temperatures.
• Do not use the device outdoors during thunderstorms.
• Use original or certified cables.
• Do not use any corrosive cleaner/oil to clean.
• The product should not be exposed to dripping or splashing water.
• The adapter shall be installed near the equipment and shall be easily accessible.

At a Glance

1. Status indicator
   Status| Status indicator light
   ---|---
   Standby| Solid red
   Bluetooth pairing mode| Flashing blue
   Bluetooth device connected| Solid blue (stays on for 10 seconds)
   AUX| Solid cyan (stays on for 10 seconds)
   Mute| Solid yellow
   Optical| Solid green (stays on for 10 seconds)
   Volume up and down| Flashing white
   Maximum volume| Solid white (stays on for 3 seconds)
   Minimum volume| Solid white (stays on for 3 seconds)
   Music| Flashing white (once)
   Movie| Flashing white (3 times)
2. Power button
3. Volume-up control
4. Volume-down control
5. Source input
6. Wall mount holes
7. USB port (Service only)
8. AUX input
9. Optical input
10. Power input

Placement

1. Place the Soundbar on a solid surface.
   

2. To prevent any hazardous situations, no naked flame sources, such as lighted candles, should be placed on or in the vicinity.

• Wall Mount Installation
  1. Drill two holes on the wall (approximately 6mm in diameter). The distance between the two holes should be 400mm. Refer to image below:
  Insert the two screw plugs into the drilled holes, then place the two screws in the screw plugs.
  2. Tighten the screws with screwdriver and leave 4mm screw head outside.
  3. Hang the Soundbar on the wall.
  

Remote Control

1. Battery installation
   

2. Remote control buttons
   

put the  Soundbar in standby mode.
2| Volume-up control| To make volume adjustments.
3| Previous| Return to previous track.
4| Play / Pause| To pause / resume playback.
5| Bluetooth button| To activate Bluetooth mode.
1. Press to activate Bluetooth mode.
2. Press and hold for 3 seconds for Bluetooth reconnection.
6| AUX button| To activate the AUX mode.
7| Music button| To activate the music equalizer mode.
8| Mute button| To temporarily turn off the sound. Press the button again to turn the sound back on.
9| Next| Move to next track.
10| Volume-down control| To make volume adjustments.
11| Optical button| To activate the optical mode.
12| Movie button| To activate the movie equalizer mode.

The status indicator light will stay on for approximately 10 seconds T when the Soundbar is in Bluetooth mode /AUX IN mode/OPTICAL IN mode.

Using Your Soundbar

1. Turn On / Off
   

The Soundbar will automatically switch to standby mode when no audio T input is received for over 15 minutes.

**a. Connect to your TV

**

1. Connect optical cable to the optical output port of a stereo audio machine (such as TV / CD / VCR / DVD player …etc).
2. Press the OPT button on the remote control to activate optical mode. The status indicator will be solid green.
   Note: the status indicator light will stay on for 10 seconds.

b. AUX-In mode

1. Connect audio cable (3.5mm to RCA stereo audio cable) to the audio output port of a stereo audio machine (such as TV / CD / VCR / DVD player …etc).
2. Press the AUX button on the remote control to activate AUX mode. The status indicator will be solid cyan.
   the status indicator light will stay on for 10 seconds.

c. Bluetooth mode

1. Press Power button on the remote control to switch on the Soundbar.
2. Press the Bluetooth button on the remote control to activate Bluetooth mode.
3. Turn on the Bluetooth of your device, search for Soundcore Infini Mini on your Bluetooth list then select connect.
   Flashing Blue| Bluetooth mode is activated
   ---|---
   Solid Blue| Connected to device
   Note: the status indicator light will stay on for 10 seconds.

 When turned on, Soundcore Infini Mini Soundbar will automatically connect to the last connected device if available. If not, press the Bluetooth button to activate Bluetooth mode.
Having connection problems? Remove Soundcore Infini Mini from your device’s Bluetooth history and ensure it’s less than 10 meters away. Then try pairing again. To get the best sound quality, make sure there is a clear line of sight between the connected device and your Soundbar.

d. Respond to your TV remote control
Use your own TV remote control to control your Soundbar (Applicable for most of Vizio / LG / Philips TVs).
Press and hold Volume-down control and Source input button (on Soundbar) for more than 3 seconds to activate the remote control learning mode. The status indicator will flash to white in this stage.

Press Power button on the Soundbar and press the Power button on your TV remote control simultaneously, then the status indicator will flash to red. Once your Soundbar is responding to your TV remote control, the status indicator on the soundbar will be solid red.
Note: only power, source input and volume of your Soundbar can be controlled by your TV remote control.
Note: refer to below table for setting up the buttons on your TV remote control. You can control power, source input and volume of your Soundbar once the TV remote control buttons are set up.

Soundbar button| TV remote control
buttons| Activation procedure| Status indicator on soundbar
---|---|---|---
Button learning| Button learnt
Power button| Power button| Press the buttons on Soundbar and TV remote control simultaneously| Flashing Red| Solid red (for 30 seconds)
Source input button| Source button| Press the buttons on Soundbar and TV remote control simultaneously| Flashing Green| Solid green (for 30 seconds)
Volume-up control| Volume-up button| Press the buttons on

Soundbar and TV remote

control simultaneously

| Flashing Blue| Solid blue (for 30 seconds)
Volume-down control| Volume-down button| Press the buttons on Soundbar and TV remote control simultaneously| Flashing Yellow| Solid yellow (for 30 seconds)

  When not in use, store your Soundbar in a cool place.

Declaration of Conformity

Hereby, Anker Innovations Limited declares that the radio equipment type A3370 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://www.anker.com/products Maximum output power: 4.0dBm Frequency band: 2.4G band (2.4000GHz-2.4835GHz)

Specifications

Specifications are subject to change without notice.
Input: 18 V 2.2 A
Audio output: 20 W x 2
Size : 550 x 63 x 94 mm / 21.6 x 2.5 x 3.7 in
Weight (without packaging): 1190 g / 42 oz
Bluetooth version: V2.1 + EDR Range: 10 m / 33 ft

Model No.: A3370
51005000947 V01

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>