COOKOLOGY CDD900BK Cooker Hood Instruction Manual
- June 3, 2024
- COOKOLOGY
Table of Contents
CDD900BK Cooker Hood
Instruction Manual
CDD600BK & CDD900BK
CDD605BK &CDD905BK
CDD600WH &CDD900WH
Cooker hood
Instruction Manual
SAFETY WARNING
Never let children operate the cooker hood.
The cooker hood is for home use only. It is not suitable for barbecues, Roast
shop and other commercial purposes.
The installation must be completed by a qualified and competent fitter, and
connect the correct power before use.
The cooker hood and its filter mesh should be cleaned regularly in order to
keep it in good working order.
Before cleaning, switch the power off at the main supply.
Clean the cooker hood according to the instruction manual and keep the cooker
hood from the danger of burning.
Prohibit putting the cookerhood by fire. If there is any fault with the
appliance, please call the service department to request a service engineer.
Thank you for choosing our cooker hood. Please read this instruction manual
carefully before installing and using the cooker hood.
The manufacturer disclaims all liability for any damage or injury caused as a
result of not following the instructions for installation that are contained
in this manual.
Notice
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
The instructions shall state the substance of the following: there shall be
adequate ventilation of the room when the range hood is used at the same time
as appliances burning gas or other fuels (not applicable to appliances that
only discharge the air back into the room);
the details concerning the method and frequency of cleaning;
there is a fire risk if cleaning is not carried out in accordance with the
instructions; do not flambé under the range hood;
CAUTION: Accessible parts may become hot when used with cooking
appliances.
The installation instructions shall include the substance of the following:
the air must not be discharged into a flue that is used for exhausting fumes
from appliances burning gas or other fuels (not applicable to appliances that
only discharge the air back into the room);
the minimum distance between the supporting surface for the cooking vessels on
the hob and the lowest part of the range hood. (When the range hood is located
above a gas appliance, this distance shall be at least 65 cm.
regulations concerning the discharge of air have to be fulfilled.
The installation instructions for range hoods with accessible metallic
enclosures of class II construction shall include details that indicate the
location and maximum permitted lengths for any fixing or mounting screw or
other fixing device that penetrates into the range hood to attach an accessory
such as a facia or duct fitting.
Where fixing or mounting screws, or other fixing devices are used, that
penetrate into the range hood with an accessible metallic enclosure of class
II construction, to attach an accessory, the instructions shall indicate the
required location of these screws or fixing devices and include the substance
of the following warning. Warning: Failure to install the screws or fixing
device in accordance with these instructions may result in electrical hazards
FEATURES
The cooker hood has a streamlined design and is made with high quality
materials.
Other features include a large power low noise electric motor and centrifugal
leaf that produces strong suction. Also, a non-stick grease filter ensures
that the cooker hood is easy to clean.
The cooker hood’s special wind tunnel construction and oil collector design
enables free dirt to be absorbed in seconds.
INSTALLATION
- The cooker hood should be placed at a distance of 15mm from the wall at least. (See Pic1)
- Put the hood into the hole of the cabinet.(See pic 2) Use 4pcs screw ST48 & screw ST414 & fixing knock to fix the hood.(See pic 3)
- Connect the casing & hood by 8pcs screw M10*10, the wind direction are up, down, left, right, the user can select according to the space of the cabinet.(See pic 4)
- Fix the pipe on the outlet, and use 4pcs screw ST4*14 to fix the PCB box, connect the power and finish the installation.(See pic 5) The distance between the edge of cooker hood and the hob should be at least 40mm.Refer to pic 6.
LAMP REPLACEMENT
BULB REPLACEMENT
Important : The bulb must be replaced by a competent person. Always switch
off the electricity supply before carrying out any operations on the
appliance. When handling bulb, make sure it is completely cool down before
any direct contact to hands.
When handling globes hold with a cloth or gloves to ensure perspiration does
not come in contact with the globe as this can reduce the life of the globe.
- Switch off the downdraft and unplug it from the main power supply.
- Open the decorative door of the downdraft.
- Insert a small screw-driver “-” type into the gap and pry up the lamp fitting and disconnect the plug (Refer Pic below).
- Replace with same type of light.
- ILCOS D code for this lamp is: DSS-1-S-120/33.5.
- LED modules rectangle LED lamp
- Max wattage: 1 W
- Voltage range: DC 12V
- Dimensions:
MAINTENANCE
Replace and clean the filter
Please follow the below filter dismantled method operation (See pic 9)
Method 1: Put the filter into 40-50°C clean water, pour on detergent, and soak
for 2-3 minutes. Wear gloves and clean with a soft brush. Please do not apply
too much pressure, as the filter is delicate and will damage easily.
Method 2: The filter can be put into a dishwasher. Set the temperature at
around 60°C. The filter is made of high-density metal. Please do not use
corrosive detergent on it. Keeping this filter clean will keep the appliance
running correctly.
Note:
- Please do not put anything which can block the up & down of the hood to avoid the damage of the hood and body injury.
- Please keep the power off when clean the hood.
SWITCH INSTRUCTION
This control system consists of two parts, power panel and touch panel. Touch
panel contains five function buttons (power, speed, light, timer, slide
control)
Timer………….. Light………… Slide control……………. Speed ……………Power
Functional Operation
-
Power on, the hood will standby with backlight, backlight will be extinguished after 5 seconds without any operation, for using the hood again, touch any key to wake up it’s standby motion.
-
Touch the power button for 2 seconds, the hood will slide upwards, and works at the first speed. Touch the power button for 2 seconds again, the hood will slide downwards, and stop working. If you stop the hood, without stopping the motor, when you open the hood again, the hood will work at the speed it works last time.
2.1 Press the power button , when the hood is coming upwards or going downwards, the hood will stop moving, with motor keeping running. Press the power button the hood will move again. again, -
Motor on/off and speed setting:
3.1 Touch the speed button , the motor will turn on; touch it again, it will
turn off.
3.2 How to set the speed? Touch this area with your finger sliding on it. When
your finger stops at the first or second point, the motor will run at the
lowest speed; when your finger stops at the third or fourth point, the motor
will run at the second speed; when your finger stops at the fifth or sixth
point, the motor will run at the third speed; when your finger stops at the
seventh or eighth point, the motor will run at the highest speed.
Lighting:
4.1. After the hood slides up, the lights will turn on automatically in 8-10
seconds.
4.2 Touch the button of light lights will turn off. , Touch the light button
again, the lights will turn off.
4.3 When you touch the button of light , the pilot light is flashing. Slide
the button to control the light intensity when the pilot light is flashing.
When enter into the controlling of light intensity, the silde button control
the light intensity. There is 8 speeds of slide button when lighting, every
speed means one light intensity. When touch slide button and slide to one
light and it will be on, the light will be on in corresponding light
intensity. It can also use the manual keys by touching the button to operate
the hoods on one pilot light and it will be on in corresponding light
intensity. The pilot light will stop flashing after 15s if no function
adjustment.
5. Timer button
5.1 Touch timer button when light or motor is working; the hood will enter
into timer working. When the pilot light of timer is flashing, slide button to
select the timer section.”
There are eight sections of timer button when timer is working, they are:
5-10-15-20-25-30-35-40, touch the timer button to enter into timer working
when confirm the timer section. Or, enter into timer working automatically 5s
later. The motor and light are off automatically when finish the timer, the
hood will enter into standby, the decorative cover will close automatically.
5.2 Use the timer function again when keep power on, touch the timer button
but without time setting, the hood will keep the time which setted on last
time. It will decrease by second after 5s.It will work as new time after new
setting.
5.3 Touch the speed button or control the light intensity when timer is
working, the timer function will cancel automatically.
Abnormity and Solution
Fault
| Cause|
Solution
---|---|---
Light on, but motor does| The leaf blocked| Get rid of the blocking
The capacitor damaged| Replace capacitor
not work| The motor jammed bearing damaged| Replace motor
The internal with of motor of or a bad smell from the motor| Replace motor
Light does not work
motor does not work| Beside the above mentioned, check the following:|
Light damaged| Replace lights
Power cord looses| Connect the wires as per the electric diagram
Oil leakage| One way valve and the air
ventilation entrance are not tightly sealed| Take down the one way valve and
seal with glue
Leakage from the connection of U-shaped section and cover| Take U-shaped
section down and seal with soap or paint
Shake of the body| The leaf damaged and causes shaking| Replace the leaf
The motor is not tightly hanged| Lock the motor tightly
The body is not tightly hanged| Fixed the body tightly
Insufficient suction| The distance between the body and the gas top too long|
Readjust the distance
Too much ventilation from open doors or windows| Choose a new place and
resemble the machine
The machine inclines| The fixing screw not tight enough| Tighten the hanging
screw and make it horizontal
The hanging screw not tight enough| Tighten the hanging screw and make it
horizontal
ENVIRONMENTAL PROTECTION:
This product is marked with the symbol on the selective sorting of waste
electronic equipment. This means that this product must not be disposed of
with household waste but must be supported by a system of selective collection
in accordance with Directive
2002/96/EC. It will then be recycled or dismantled to minimize impacts on the
environment, electrical and electronic products are potentially dangerous for
the environment and human health due to the presence of hazardous substances.
For more information, please contact your local or regional authorities.
Note
a. In order to reduce the environmental impact (e.g. energy use) of the
cooking process, please be sure that your product is installed according to
the user manual, keep the operation place ventilated, keep the extraction duct
be direct and short as possible as it can be.
b. For the product with manual operation mode, we suggest switch the motor off
within 10 minutes after finishing the cooking process.
c. Please be sure to dismantle related components according to the user manual
when maintaining for non-destructive, protect the parts to make the re-
installed work can be favoring and avoid damage.