hager WHEC2526XXXXX kallysto Smart Switch Instruction Manual
- June 3, 2024
- hager
Table of Contents
hager WHEC2526XXXXX kallysto Smart Switch
Safety instructions
Electrical equipment must only be installed and assembled by a qualified electrician in accordance with the relevant installation standards, regulations, directives and safety and accident prevention directives of the country.
Failure to comply with these instructions may result in damage to the device,
fire or other hazards.
The radio transmission is not suitable for safety or alarm applications.
These instructions are an integral component of the product and must be
retained by the end user.
Design and layout of the device
Figure 1: Fundamental design and layout of the device
- Frame
- Front
- kallysto Smart Switch
- Buttons
Function
Correct usage
- Smart light switch for wireless control of Philips Hue lamps.
- For switching, dimming and recalling light scenes.
- Radio application in acc. with RED 2014/53/EU with particularly low energy consumption.
- Installation on device box, render or level surfaces with screws and adhesive pads.
- Only suitable for use in indoor areas with no drip and no spray of water. kallysto CH Friends of Hue Smart Switch are suitable for residential use only and require a Philips Hue Bridge (v2) and Philips Hue App for Android or iOS for initial commissioning Ensure that Philips Hue lamp is always powered. The Philips Hue lamp can only be controlled by the Philips Hue system when the light is powered on.
Please be aware that Signify has access to personal data and user data via the
Hue Bridge.
Signify’s privacy policy and terms and conditions of use are available at www
.philips-hue.com. The processing of personal data
and user data is explained there.
Product characteristics
- Batteryless and maintenance-free device without external power supply.
- Encrypted transfer with device-specific code.
- ZigBee Green Power radio standard, compatible with Friends of Hue and Apple HomeKit.
- Easy commissioning and configuration via Philips Hue App and Philips Hue Bridge, (v2)
- Transmission power is obtained from mechanical energy when the button is pressed (energy harvesting).
- kallysto CH Friends of Hue Smart Switch consists of 4 push-buttons.
Operation
Operating concept
A short and long press can be allocated to functions on each button
(switching, dimming, scenes).
Information for electricians
Installation and electrical connection
DANGER!
Electrical shock when live parts are touched!
An electric shock can lead to death!
Isolate all power before working on the device and cover any live parts in the
area!
Selecting installation location
The transmission reach in buildings is approximately 15 m without wall penetration. A maximum of one wall penetration is recommended as otherwise the radio signal is weakened.
Figure 2: Reduction of range through construction obstacles
The receiver may not be able to properly process the transmitter signal if it penetrates several walls.
Metals, such as metallic door frames, etc., can also have a negative impact on transmission.
The reach can be extended with Philips Hue lamps in each room.
Installation with adhesive pads (figure 3)
Figure 3: Installation with adhesive pads
Adhesive pads
The mounting surface is clean, free of grease and offers sufficient support.
- Stick adhesive pads (5) onto the back of the supporting plate (2) in the indentations intended for this purpose.
- Place the supporting plate (2) in the frame (1).
- Place the supporting plate and frame on the mounting surface in the correct position, “TOP” and push firmly for 15 seconds.
- Click the kallysto Smart Switch (3) into the supporting plate (2). Pay attention to the marking top on the module.
- Push the buttons (4) onto the kallysto Smart Switch (3) in the right position until they engage.
The adhesive pads only reach their final adhesion after approx. 24 hours.
Select your location carefully before installation.
After the switch has been properly adhered to the surface, it becomes harder
to remove.
Before installation, commission the device and test the reach prior to using
the adhesive pads.
Installation with screws (figure 4)
Figure 4: Installation with screws
Dowels
Screws
- Use the supporting plate (2) as a template and mark the boreholes.
- Drill 5 mm wall plug holes.
- Fix the frame (1) and supporting plate (2) with the “ top” marking on the wall with a screw/ wall plug connection (6/7).
- Click the kallysto Smart Switch (3) into the supporting plate (2). Pay attention to the marking top on the module.
- Push the buttons (4) onto the kallysto Smart Switch in the right position and press until they engage.
Installation on a wall box (figure 5/6)
Wall box
Fixing plate
Fixing ring
Fastening claws (only used when installing on wall box) An existing installation can be extended by using the next bigger frame (not included in the scope of delivery) (figure 6).
- Remove any previously installed switches.
- Change existing wiring so that the lighting is permanently powered on.
- Install the fixing plate (9) on the wall box (8) with the fixing ring (10) in the correct position, “TOP”.
- Push the frame (1) and supporting plate (2) onto the fixing ring (10) until the fastening claws (11) engage.
- Click the kallysto Smart Switch (3) into the supporting plate (2). Pay attention to the marking top on the module.
- Push the buttons (4) onto the radio module (3) in the right position until they engage.
Dismantling the kallysto Smart Switch (figure 7)
Follow the steps in figure 7 for dismantling.
Commissioning
Follow the Philips Hue App instructions for commissioning and configuration.
Connect the switch to the Philips Hue Bridge
The Philips Hue Bridge is ready for operation and within reach of the kallysto
Smart Switch.
-
The system requires a Philips Hue Bridge (v2) and Philips Hue app for Android or iOS for initial setup. Learn more on Philips-hue.com.
The Philips Hue App must be connected with your Bridge. -
Select the “Settings” > “Accessories setup” > “Friends of Hue Switch” menu in the Philips Hue App.
All compatible Friends of Hue switches are displayed. -
Select kallysto Smart Switch.
Operate the buttons (4) of the kallysto Smart Switch as described in the app.
The kallysto Smart Switch has received the information and has been added as an accessory in the app.
The kallysto Smart Switch can be configured in the app.
Configuration
The button functions (switching, dimming, scene) have to be configured in the
Philips Hue App.
Configuring the kallysto Smart Switch in the Philips Hue App Philips Hue lamps are ready to use.
- Follow the instructions as described in the app and allocate the kallysto Smart Switch to the lamps and configure it.
Appendix
Technical data
- Carrier frequency: 2.4 … 2.483 GHz
- Zigbee Green Power as per IEEE 802.15.4
- Transmission range in buildings approx. 15 m
- Transmission power: 7 dBm/5mW
- Degree of protection IP: IP20
- Storage temperature: -25 … +65 °C
- Ambient temperature: +5 … +45 °C
Accessories
- Replacement kit WHEC202631XXH
- 1×2 / 2×1 frame for expansion
- line WH25930xxxZ
- trend WH26930xxxZ
- pro-WH27930xxxZ
Troubleshooting
Philips Hue receiver does not respond.
- Cause 1: The Philips Hue lamp has not been switched on.
- Switch on the Philips Hue bulb with a conventional switch.
- Cause 2: kallysto Smart Switch is not connected with the lamp to be switched.
- Open the Philips Hue App and check the connection between the switch and lamp.
Warranty
We reserve the right to realise technical and formal changes to the product in
the interest of technical progress.
Our products are under guarantee within the scope of the statutory provisions.
If you have a warranty claim, please contact the point of sale.
Correct disposal of this product (electrical waste).
(Applicable in the European Union and other European countries with separate
collection systems).
This marking shown on the product or its documentation indicates that it
should not be disposed of with other household waste at the end of its working
life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this device from other types of
waste. Recycle the device responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take this device for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial waste for disposal.
Hager Group herewith declares that kallysto Smart Switch Friends of Hue meet
Directive 2014/53/EU.
The complete text of the EU declaration of conformity is available at
www.hager.com.
Tél. 041 269 90 00
Fax 041 269 94 00 hager.ch
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>