Bob Vila Refrigerator Water Filter Installation Guide
- June 7, 2024
- Bob Vila
Table of Contents
Refrigerator Water Filter
INSTALLATION INSTRUCTION
A REPLACEMENT FOR THE FOLLOWING WATER FILTER:
XWF
FILTER LIFE:
6 months or 200 gallons, Whichever comes first will vary based on water
condition.
OPERATING SPECIFICATIONS:
Min. operating temperature…..33°F/0.6°C
Max. operating temperature…..00°F/38°C.
Min. working pressure…..25 psi/172 kPa
Max. working pressure…..20 psi/827 kPa
Rated capacity…..200 gallons/757 litres
Flow rate…..5 gpm/1.9 lpm
INSTALLING THE FILTER IN A BOTTOM FREEZER REFRIGERATOR
-
Open the filter cartridge housing by squeezing the 2 front tabs and gently
pulling down -
Remove old filter by slowly rotating it to the left. A small amount of water
may drip down. -
Line up the ports on the filter with the ports on the filter cartridge holder, and
gently insert the filter. -
Slowly turn the filter to the right until it stops. As you tun the filter, it will
automatically adjust itself into position. The filter will move 90 degrees, until
the arrow on the filter aligns with the arrow on the filter cartridge holder.
NOTE: PLEASE DO NOT OVER TIGHTEN. -
Slowly push the filter up into the clips. Close the cover by gently pushing
the lid upwards until the tabs lock into place. -
Run water from the dispenser for 2 gallons or approximately 5 minutes to clear
the system. Water may spurt out and air bubbles may be visible during this
process. If water is not flowing, check to make sure the filter has been fully
rotated to the right -
Press and hold the RESET WATER FILTER pad (only on select models) on
the dispenser for three seconds
INSTALLING THE FILTER CARTRIDGE IN A SIDE BY SIDE
REFRIGERATOR
-
Rotate 90 degrees to the left to remove the old filter.
-
Line up the arrow on the filter with the arrow on the filter cartridge holder.
Gently push the top of the new filter up inside the holder. -
Slowly turn the filter to the right until it stops. As you turn the filter, it will
automatically adjust itself into position. The filter will move 90 degrees.
NOTE: PLEASE DO NOT OVERTIGHTEN. -
Run water from the dispenser for 2 gallons or approximately 5 minutes to clear
the system. Water may spurt out and air bubbles may be visible during this
process. If water is not flowing, check to make sure the filter has been fully
rotated to the right -
Press and hold the RESET WATER FILTER pad (only on select models) on
the dispenser for three seconds
RESETTING YOUR CHANGE FILTER INDICATOR:
Note: These are the most common filter reset instructions. If the
instructions don’t work for your
refrigerator brand, see the documentation that came with your refrigerator.
REFRIGERATOR BRAND – GE? or Hotpoint®
INSTRUCTIONS – Press and hold the reset water filter button on the
dispenser for three seconds.
STORAGE AND MAINTENANCE:
-
Replace your filter every 6 months or 200 gallons to achieve optimal performance and prevent
bacteria and fungus growth in your filter and supply lines. -
Keep your unused filters in a cool, dark, and dry place until you need them.
FREQUENTLY ASKED QUESTIONS:
Q: Why is it difficult to twist the new filter into the filter housing?
A: The connector may expand because of water pressure. Therefore, it is
recommended you push
the new filter in with a little bit of force, but not too hard. Then turn it
clockwise.
Q: Must the filter be changed every 6 months?
A: Yes. You must replace the filter every 6 months or sooner if water flow is
reduced or if there is
heavy sediment/rust sediment. Over-used filters will degrade the filtration
performance.
Q: Do I need to flush the filter after installation?
A: After installation, it is highly recommended you run water from dispenser
for 5 minutes before using.
Water filters are made from advanced coconut carbon block, so there are some
carbon fines in the filter. Flushing removes the carbon fines to produce clean
water.
WARNING:
To reduce the risk of property damage due to water leakage, this filter MUST
be installed in accordance
with the manufacturer’s specifications and instructions. This filter unit must
be replaced every 200 gallons
or 6 months. Failure to follow instructions and operating specifications will
void your warranty. Further,
manufacturer assumes no responsibility or liability for damages arising out of
misuse of the product.
GE® is a registered trademark of General Electric CORP.
CUSTOMER SERVICE:
1-888-352-3558 Mon-Fri 8:00 AM-5:00 PM
(PST)
service@water-filter.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>