TEFCOLD GlassDoor Display Freezer with Light Canopy User Manual
- June 3, 2024
- TEFCOLD
Table of Contents
TEFCOLD GlassDoor Display Freezer with Light Canopy
Important safety instructions
- To obtain full use of the cabinet, we recommend reading this instruction manual.
- It is the user’s responsibility to operate the appliance in accordance with the instructions given.
- Contact your dealer immediately in case of any malfunctions.
- Place the cabinet in a dry and ventilated place.
- Keep the cabinet away from strongly heat-emitting sources and do not expose it to direct sunlight.
- Always keep in mind that all electrical devices are sources of potential danger.
- Do not store inflammable material such as thinner, gasoline etc. in the cabinet.
- We declare that no asbestos nor any CFC are used in the construction.
- The oil in the compressor does not contain PCB.
Unpacking and installation
Remove the wooden pallet and the packing.
To ensure correct function it is important that the cabinet is level. If the
cabinet is supplied with legs, these can be adjusted. See fig. 1.1.
If you want to build in your cabinet please note the following:
1. There must be at least 10 cm free space above the cabinet in order for the
cooling system to work satisfactorily.
2. There must be sufficient space at the hinge side to clean and replace the
shelves and clean around the hinge.
Electrical connecting
The cabinet operates on 230 V/50 Hz.
The wall socket should be easily accessible.
All earthing requirements stipulated by the local electricity authorities must be observed. The cabinet plug and wall socket should then give correct earthing. If in doubt, contact your local supplier or authorized electrician.
The flexible cord fitted to this appliance has three cores for use with a 3-pin 13-Amp or 3-pin 15- Amp plug. If a B.S. 1363 (13-Amp) fused plug is used, it should be fitted with a 13Amp fuse.
The wires in this mains lead are cultured in accordance with the following code: Green/Yellow: Earth, Blue: Neutral, Brown: Live.
The main electrical connections must be done by skilled electricians.
Start-up of the cabinet
Before use, we recommend that the cabinet is cleaned, see the section on maintenance and cleaning.
Important !
If the cabinet has been horizontally placed during transport, please wait 2
hours before starting up the cabinet.
Light
The light switch is placed in the bottom panel.
Lock
The lock is placed in the bottom panel.
Thermostat
The thermostat is placed in the control panel, see fig. 2.0.
The thermostat has been pre-set and in most cases it is not necessary to
adjust the settings.
When turning on the cabinet the display will show the current temperature in
the cabinet.
Display set temperature:
Press
this key and the display will show the set temperature. Press the key again to
return to normal reading
Set new temperature:
Press
this key continuously for more than 3 seconds and the display shows the set
temperature.
Press
this key to increase the set temperature.
Press
this key to lower the set temperature.
Press
this key to save the new settings. The display will flash with the new value
and will then return to normal reading
Alarm codes:
P1’ Flashing in the display: indicates that the cabinet sensor is
defective.
The cabinet will strive to keep the set temperature until it has been
repaired.
‘P2’ Flashing in the display: indicates that the evaporator sensor is
defective.
This does not influence the operation of the cabinet, but should be repaired
as soon as possible.
Defrosting
The cabinet defrosts automatically with pre-set intervals. If the door to the cabinet is opened or the contents of the cabinet is changed frequently it may become necessary to defrost the cabinet manually.
Pressing this key continuously for more than 3 seconds will start a manual
defrosting and then return to normal operation.
Defrosted water runs to a container placed in the compressor compartment and evaporates.
Maintenance and cleaning
Switch the cooler off at the socket.
The cabinet must be periodically cleaned. Clean the external and internal surfaces of the cabinet with a light soap solution and subsequently wipe dry
Do NOT use cleansers containing chlorine or other harsh cleansers, as these can damage the stainless steel surfaces and the internal cooling system.
Clean the condenser and the compressor compartment using a vacuum cleaner and a stiff brush.
Do NOT hose the compressor compartment with water as this can cause short circuits and damage on the electrical parts.
Service
The cooling system is a hermetically sealed system and does not require supervision, only cleaning.
If the cabinet fails to cool, check if the reason is a power cut.
If you cannot locate the reason to the failure of the cabinet, please contact your supplier. Please inform model and serial number of the cabinet. You can find this information on the rating label which is placed inside the cabinet in the top right hand side.
Disposal
Disposal of the cabinet must take place in an environmentally correct way. Please note existing regulation on disposal. There may be special requirements and conditions which must be observed.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>