TEFCOLD EXTRA1250CD Multideck Cooler Freezer User Manual
- June 4, 2024
- TEFCOLD
Table of Contents
TEFCOLD EXTRA1250CD Multideck Cooler Freezer
IMPORTANT SAFETY INSTRUCTIONS
- To obtain full use of the cabinet, we recommend reading this instruction manual.
- It is the user’s responsibility to operate the appliance in accordance with the instructions given.
- Contact your dealer immediately in case of any malfunctions.
- Place the cabinet in a dry and ventilated place.
- Keep the cabinet away from strongly heat-emitting sources and do not expose it to direct sunlight.
- Always keep in mind that all electrical devices are sources of potential danger.
- Do not store inflammable material such as thinner, gasoline etc. in the cabinet.
- We declare that no asbestos nor any CFC are used in the construction.
- The oil in the compressor does not contain PCB.
- ONLY FOR APPLIANCES WITH REFRIGERANT R290/R600a!
This appliance contains a flammable refrigerant, so make sure of good ventilation around the appliance. Do not use mechanical devices when defrosting, this can cause leakage of the cooling system. Do not use electrical appliances inside the refrigerated storage compartment. Any repair of the appliance should be carried out by a skilled technician (EN 60335-2-89: 2010).
UNPACKING AND INSTALLATION
Remove the wooden pallet and the packing. External surfaces are supplied with
a protection foil, which must be removed before installation.
ELECTRICAL CONNECTION
The cabinet operates on 220-240 V/50 Hz. The wall socket should be easily
accessible. All earthing requirements stipulated by the local electricity
authorities must be observed. The cabinet plug and wall socket should then
give correct earthing. If in doubt, contact your local supplier or authorized
electrician. The main electrical connections must be done by skilled
electricians.
START-UP OF THE CABINET
Before use, we recommend that the cabinet is cleaned, see the section on maintenance and cleaning.
THERMOSTAT
The thermostat has been pre-set and in most cases it is not
necessary to adjust the settings. When turning on the cabinet the display will
show the current temperature in the cabinet.
Display set temperature:
Press this key and the display will show the set temperature. Press the key
again to return to normal reading
Set new temperature:
- Press this key continuously for more than 3 seconds and the display shows the set temperature.
- Press this key to increase the set temperature.
- Press this key to lower the set temperature.
- Press this key to save the new settings. The display will flash with the new value and will then return to normal reading.
Alarm codes:
-
‘P1’ Flashing in the display: indicates that the cabinet sensor is defective.
The cabinet will strive to keep the set temperature until it has been repaired. -
‘P2’ Flashing in the display: indicates that the evaporator sensor is defective.
The cabinet will strive to keep the set temperature until it has been repaired.
Unlock keyboard: Press both these keys for 5 seconds to activate the
keyboard.
On/Off: Press this key to turn on/off the cabinet.
LIGHT : Press this key to turn the light on/off. (Keyboard must be
unlocked)
DEFROSTING
The cabinet defrosts automatically with pre-set intervals. If the contents of
the cabinet is changed frequently it may become necessary to defrost the
cabinet manually.
- Pressing this key continuously for more than 5 seconds will start a manual defrosting and then return to normal operation.
Defrosted water runs to a container placed in the compressor compartment and evaporates.
CLEANING AND MAINTENANCE
Switch the cooler off at the socket. The cabinet must be periodically cleaned.
Clean the external and internal surfaces of the cabinet with a light soap
solution and subsequently wipe dry. External surfaces can be maintained using
steel oil. Do NOT use cleansers containing chlorine or other harsh cleansers,
as these can damage the stainless steel surfaces and the internal cooling
system. Clean the condenser and the compressor compartment using a vacuum
cleaner and a stiff brush. Do NOT hose the compressor compartment with water
as this can cause short circuits and damage on the electrical parts.
SERVICE
The cooling system is a hermetically sealed system and does not require
supervision, only cleaning. If the cabinet fails to cool, check if the reason
is a power cut. If you cannot locate the reason to the failure of the cabinet,
please contact your supplier. Please inform model and serial number of the
cabinet. You can find this information on the rating label which is placed
inside the cabinet in the top right hand side.
DISPOSAL
Disposal of the cabinet must take place in an environmentally correct way.
Please note existing regulation on disposal. There may be special requirements
and conditions which must be observed.