TEFCOLD SSF150 Supermarket Freezer Box User Manual

TEFCOLD SSF150 Supermarket Freezer Box

Important safety instructions

1. To obtain full use of the cabinet, we recommend reading this instruction manual.
2. It is the user’s responsibility to operate the appliance in accordance with the instructions given.
3. Contact your dealer immediately in case of any malfunctions.
4. Place the cabinet in a dry and ventilated place.
5. Keep the cabinet away from strongly heat-emitting sources and do not expose it to direct sunlight.
6.  Always keep in mind that all electrical devices are sources of potential danger.
7.  Do not store inflammable material such as thinner, gasoline etc. in the cabinet.
8.  We declare that no asbestos nor any CFC are used in the construction.
9. The oil in the compressor does not contain PCB.

This appliance contains a flammable refrigerant, so make sure of good ventilation around the appliance. Do not use mechanical devices when defrosting, this can cause leakage of the cooling system. Do not use electrical appliances inside the refrigerated storage compartment. Any repair of the appliance should be carried out by a skilled technician (EN 60335-2-89: 2010).

**Unpacking and installation

**

Remove the wooden pallet and the packing. Stainless steel surfaces are supplied with a protection foil, which must be removed before installation

Electrical connecting
The cabinet operates on 230 V/50 Hz. The wall socket should be easily accessible. All earthing requirements stipulated by the local electricity authorities must be observed. The cabinet plug and wall socket should then give the correct earthing. If in doubt, contact your local supplier or authorized electrician. The flexible cord fitted to this appliance has three cores for use with a 3-pin 13-Amp or 3-pin 15-Amp plug. If a B.S. 1363 (13-Amp) fused plug is used, it should be fitted with a 13-Amp fuse. The wires in this mains lead are colored in accordance with the following code: Green/Yellow: Earth, Blue: Neutral, Brown: Live. The main electrical connections must be done by skilled electricians.

Start-up of the cabinet
Before use, we recommend that the cabinet is cleaned, see the section on maintenance and cleaning.

Important
If the cabinet has been vertically placed during transport, please wait 2 hours before starting up the cabinet.

Thermostat Dixell

Display set temperature:
Press this key and the display will show the set temperature. Press the key again to return to normal reading.

Set new temperature:
Press this key for 3 sec. and the display shows the set temperature.

• Press this key to increase the set temperature.
• Press this key to lower the set temperature.
• Press this key to save the new settings. The display will flash with the new value and will then return to normal reading.

Changing of parameters:

•  Press these keys continuously for 5 seconds to access the list of parameters.
• Press this key to scroll up through the parameter list.
• Press this key to scroll down through the parameter list.
• Press this key to select the parameter to change, the display will show the actual value, use the up/down keys to change the value and confirm with ’Set’:
• The display will return to normal reading after 15 sec. See table of parameters from page 34.

Alarm codes:
Flashing in the display: indicates that the cabinet sensor is defective Flashing in the display: indicates that the temperature is too high.  Flashing in the display: indicates that the temperature is too low.

Thermostat Carel

Display set temperature:

• Press this key and the display will show the set temperature. Press the key again to return to normal reading.
• Press this key and the display shows the set temperature.
• Press this key to increase the set temperature.
• Press this key to lower the set temperature.
• Press this key to save the new settings. The display will flash with the new value and will then return to normal reading.
• Press this key continuously for 5 seconds to access the list of parameters. Display shows ’PS’, press SET and use UP/Down keys to enter password ’22’. Press SET.
• Press this key to scroll up through the parameter list.
• Press this key to scroll down through the parameter list.
• Press this key to select the parameter to change, the display will show the actual value, use the up/down keys to change the value and confirm with ’Set’:

Press the SET key continuously for 5 seconds to store the data. See table of parameters from page 34.

Alarm codes:
EO Flashing in the display: indicates that the cabinet sensor is defective. HI Flashing in the display: indicates that the temperature is too high. LO Flashing in the display: indicates that the temperature is too low.

Defrosting
We recommend defrosting the freezer every three month or if the layer of ice exceeds 5 mm. Do never use metal or other sharp objects to scrape the internal sides as it can damage the freezer

1. Disconnect the freezer
2.  Empty the freezer
3. Leave the freezer with the lid open
4.  Use the plastic scraper to remove the ice from the inner liner
5. Remove the drain plug and open the drain on the backside of the freezer and place a tray under the drain
6. Clean the freezer with mild detergent and wipe thoroughly
7. Connect the freezer and it is ready for use.

Maintenance and cleaning
Switch the freezer off at the socket. The cabinet must be periodically cleaned. Clean the external and internal surfaces of the cabinet with a light soap solution and subsequently wipe dry. Stainless steel surfaces can be maintained using steel oil. Do NOT use cleaners containing chlorine or other harsh cleansers, as these can damage the surfaces and the internal cooling system. Clean the condenser and the compressor compartment using a vacuum cleaner and a stiff brush. Do NOT hose the compressor compartment with water as this can cause short circuits and damage on the electrical parts. Service The cooling system is a hermetically sealed system and does not require supervision, only cleaning. If the cabinet fails to cool, check if the reason is a power cut. If you cannot locate the reason to the failure of the cabinet, please contact your supplier. Please inform model and serial number of the cabinet. You can find this information on the rating label which is placed inside the cabinet in the top right-hand side.

Disposal
Disposal of the cabinet must take place in an environmentally correct way. Please note existing regulations on disposal. There may be special requirements and conditions which must be observed.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>