DESIGNlab LDT4826GD Loadout 48″ Gaming Desk Instruction Manual
- June 7, 2024
- DESIGNlab
Table of Contents
LDT4826GD (SF)
LOADOUT 48” GAMING DESK
ASSEMBLY INSTRUCTIONS
IMPORTANT-PLEASE KEEP THESE INSTRUCTIONS IN CASE OF ANY CUSTOMER SERVICE ISSUES
WARNING
- Use this product only one person at a time.
- Do not use this product unless all bolts screws and knobs are securely tightened.
- Check that all bolts screws and knobs are tight every three months or as needed.
- Do not overturn the back tilt knob when decreasing tension.
- Dispose of packing material properly. Do not use plastic covers as head covering. It may cause suffocation.
- Do not use the product as a stepladder.
- Use this product for its intended purpose only.
- Use mild detergent only for cleaning.
OSP FURNITURE LIMITED PRODUCT WARRANTY
Design Lab Products
- 3 years on gaming desks and chairs
- Upholstery is not warranted against routine scratching and scuffing
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty-hour workweek by persons weighing 250 lbs. or less. This warranty will not cover labor, freight, or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting acts of nature, or any other event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or consequential damages is excluded. The user assumes all risk of injury resulting from the use of this product. When usage is more than 40 hours per week, a two-year warranty on all parts applies. Fabric and foam are warranted for one year. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
It is the customer’s responsibility to prepay freight on any components
returned to the factory. Return freight on components covered by warranty will
be paid by Office Star Products.
Our quality standards are among the highest in the industry. Sometimes, no
matter how hard we try, there are times when parts are damaged or missing. Our
Parts Department will do everything possible to promptly remedy the problem.
Contact us via e-mail parts@officestar.net, by Fax
1-909-930-5629, or toll free parts
number 1-800-950-7262, Monday through
Friday 8:00 a.m. – 5:00 p.m. Pacific Time.
CAM LOCK INSTALLATION
| Screw Cam Screw-in. Fully
Tighten.
---|---
|
Align hole in panel with Cam Screw.
| Screw Cam
Nut in. Turn clockwise until you feel Cam Nut securely fasten to Cam Screw.
Fully tighten Cam Nut.
HARDWARE LIST
HARDWARE LIST
NO| DRAWING| DESCRIPTION| SIZE| QUANTITY
A| | Glue| 0| 1 PC
B| | Wooden Dowel| 0| 4 PCS
C| | Cam Screw| 0| 8 PCS
D| | Cam Nut| 0| 8 PCS
E| | Allen Wrench| 0| 1 PC
F| | Allen Bolt| 6 x 12 x 10mm| 12 PCS
G| | Allen Bolt| 6 x 25 x 10mm| 2 PCS
H| | Allen Bolt| 6 x 32 x 10mm| 8 PCS
I| | Allen Bolt| 6 x 45 x 10mm| 2 PCS
J| | Wood Screw| 4 x 12 x 8mm| 2 PCS
K| | Wood Screw| 3.5 x 12x 8mm| 2 PCS
L| | Flat Head Allen Bolt| 6 x 32 x 10mm| 7 PCS
Phillips Screwdriver also needed for assembly (not provided).
PARTS
| (1) Top
Shelf (1 PC)
---|---
| (2) Desktop
(1 PC)
| (3) Left Side Frame (1 PC)
| (4) Right Side Frame (1 PC)
| (5) Back
Panel (1 PC)
| (6) Middle Front Crossbar (1 PC)
| (7)
Rear Lower Crossbar (1 PC)
| (8)
Upper Crossbar (1 PC)
| (9) Rear
Frame (1 PC)
| (10) Left Upper Frame (1 PC)
| (11) Right Upper Frame (1 PC)
| (12) Accessory Hook (1 PC)
| (13) Cup Holder (1 PC)
| (14) Wireless Charger (1 PC)
| (15) Power Outlet (1 PC)
| (16) Remote Control (1 PC)
| (17) LED Power Supply (1 PC)
| (18) Storage Tray (1 PC)
STEP 1
STEP 2
Remove all the parts from carton, separate them into part numbers indicated
on the list and make sure part quantities are correct.
STEP 1 Screw-in four Cam Screws (C) into Desktop (2), two Cam Screws (C) into
both Left Side Frame (3) and Right Side Frame (4). FULLY TIGHTEN ALL CAM
SCREWS (C). Insert four Wooden Dowels (B) into Back Panel (5). Use a small
amount of Glue (A) per hole, be careful not to overfill the hole.
Note: Using a rubber mallet, gently tap Wooden Dowel (B) to ensure it is
sitting properly.
STEP 2 Attach Left Side Frame (3) and Right Side Frame (4) to Middle Front
Crossbar (6) and Back Panel (5) using two Cam Nuts (D) and two Allen Bolts (F)
for each side frame . FULLY TIGHTEN ALL CAM NUTS (D) AND ALL ALLEN BOLTS
(F).
STEP 3
STEP 4
STEP 3 Secure top end of Back Frame (9) to Back Panel (5) using two Allen
Bolts (G). Secure Rear Lower Crossbar (7) using two Allen Bolts (F). FULLY
TIGHTEN ALL ALL ALLEN BOLTS (F & G).
STEP 4 Attach Desktop (2) to assembly and secure using four Cam Nuts (D), four
Allen Bolts (H) and four Allen Bolts (F). FULLY TIGHTEN ALL CAM NUTS (D) AND
ALL ALLEN BOLTS (H & F).
STEP 5
STEP 5 Attach Cup Holder (13), Wireless Charger (14), and Storage Tray
(18) to desktop. Secure Power Outlet (15) to the desktop using two Wood Screws
(K).
Secure Accessory Hook (12) to the side of the desk using two Wood Screws (J).
FULLY TIGHTEN ALL WOOD SCREWS (J & K).
STEP6
NOTE: There are THREE different positions for the Add-On Shelves as show
in Figure 1.
Please decide your preferred height at this time
STEP 6 Secure Left Upper Frame (10) and Right Upper Frame (11) to rear of
assembly using two Allen Bolts (H) for each frame.
FULLY TIGHTEN ALL ALLEN BOLTS (H).
STEP 7
STEP 8
STEP 7 Secure Upper Crossbar (8) between Left Upper Frame (10) and Right
Upper Frame (11) using two Allen Bolts (F). FULLY TIGHTEN ALLEN BOLTS (F).
STEP 8 Secure Top Shelf (1) to assembly using seven Flat Head Allen Bolts (L).
FULLY TIGHTEN ALL FLAT HEAD ALLEN BOLTS (L).
STEP 9
STEP 9 Connect cord of Top Shelf (1) to LED Power Supply (17).
WIRELESS CHARGER – SAFETY WARNINGS & INSTRUCTIONS FOR USE
Your desk includes wireless charging capabilities using the wireless charger as shown. Please carefully follow the instructions and safety warnings below before using the wireless charger with your supported device.
NOTE: The wireless charger included supports most devices with wireless charging capabilities. Please consult your device’s OEM instruction manual for proper wireless charging use, safety warnings, and limitations. Stop using the wireless charger IMMEDIATELY if your device becomes hot. Improper use of the wireless charger, using non-compatible devices, or tampering with the wireless charger in any way may cause device failure, damage, or injury.
SAFETY WARNING – PLEASE READ FIRST
Devices with cases thicker than 4mm may not allow wireless charging. Remove the case from the device or use the USB port for wired charging instead.
Devices with rings, kickstands, or finger grip accessories will not allow wireless charging. Remove the accessories or use the USB port for wired charging instead.
DO NOT attempt to wireless charge devices with metallic cases, metallic attachments, or magnetic attachments. Remove the device from such cases or use the USB port for wired charging instead.
DO NOT allow any metallic foreign objects or liquids to come in contact with the wireless charger. Only devices that support wireless charging should be put on the wireless charger surface.
Rotate the dust
cover 90 degrees counter-clockwise to cover the USB charging port when not in
use.
To Power ON the Wireless Charger
Plug the USB cable from the bottom of the wireless charger into any powered USB 2.0 port, or any 5V power adapter that accepts a USB plug.
USB Port on the wireless charger will light up RED once powered on. The charger is now ready to use.
Using the Wireless Charger
To charge your device using wireless charging, place the device centered on
the wireless charger face and wait for the device to indicate it has begun
charging.
Using the USB Charge Port
To charge your device using a USB charging port, plug in your device’s USB
charging cord into the USB port as shown and wait for the device to indicate
it has begun charging.
LED LIGHT REMOTE CONTROL – INSTRUCTIONS FOR USE
Your desk includes an integrated LED light strip with customizable RGB LED
lights. The lights are controlled using the included LED Remote Control.
Please refer to the Button Feature Diagram below for an outline of the
remote’s functions. A Troubleshooting FAQ is also included below for
frequently asked questions and general usage troubleshooting. This remote uses
a single CR2025 3V Lithium coin battery, located in the pull-out battery tray
tab on the back-bottom edge of the remote.
LED Light Remote Control: Button Feature Diagram
TROUBLESHOOTING FAQ
Problem:| Solution:| Also Check:| Also Check:
Q: LED Lights won’t turn on?| Press the Power ON/OFF button| Double-check
that the LED Power Supply is connected to the LED strip on the desk and the
power supply is plugged into a power outlet.| Remove the clear tab from the
battery tray on first use. After prolonged usage, the battery (CR2025-3V
Lithium) may need to be replaced.
Q: DYI lights will not program?| When first programming the DIY section,
the lights will start off white. Hold DOWN any of the RGB colored arrows
firmly until you see the light begin to shift in color. Once a color range has
been removed, it is easier to begin customizing the DIY color. Make sure to
press the SAME DIY # button you first pressed during the programming process
to save the custom color
IMPORTANT-PLEASE KEEP THESE INSTRUCTIONS IN CASE OF ANY CUSTOMER SERVICE ISSUES
FCC INSTRUCTIONS
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
— This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
— Instructions shall caution users that modifications not approved by the
party responsible for compliance could void user’s authority to operate the
equipment.
Office Ster Products
Model Number:
© Office Star Products September 2020
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>