RECTORSEAL EZ TRAP EZT224 3/4 Inch Compact Threaded Overflow Switch Instruction Manual

RECTORSEAL EZ TRAP EZT224 3/4 Inch Compact Threaded Overflow Switch

Product Information

• Product Name: EZ Trap EZT224 Overflow Switch
• Description: The EZ Trap EZT224 overflow switch is a compact threaded switch designed to provide overflow protection by threading into the fitting on secondary drain pans. It includes a 3/4 male threaded street ell, float switch assembly, and a 72-inch cable.
• Packaging: Code 83224, Description EZT224, Qty per Case 10, Lbs per Case 4.60, Cubic Feet .34
• Applications: The overflow switch can be threaded into the fitting on secondary drain pans.

Product Usage Instructions

1. Screw the 3/4 Threaded Slip Street Ell (A) into the 3/4 drain pan overflow outlet.
2. Press fit the Float Switch Assembly (B) into the opening at the top of Street Ell (A). Do not use glue. Check that the Actuator Arm and Float move freely inside Ell.
3. Press the plug end of the Modular Cable (C) into the Float Switch Assembly (B).
4. Attach the provided service and cleaning labels as indicated.

Note: Insulation is required when installing the trap in an unconditioned space where sweating can occur.

Wiring Instructions

1. Turn off the electrical power at the main panel before installing the EZ Trap switch.
2. An in-line fuse is necessary to protect the 24V circuit.
3. Connect the Float Switch according to the provided wiring diagram.
4. Test the system for proper operation by lifting the float.

Operating Procedure
If a blockage occurs in the condensate drain line, the float will lift to stop the operation. To reset, press the center button on the switch.

Limited Warranty
For more information on the product’s limited warranty, please visit RectorSeal.com.

Manufactured by:
RectorSeal, LLC
2601 Spenwick Drive
Houston, TX 77055, USA
800-231-3345
Fax 800-441-0051
3255 Wyandotte St. East, Windsor, ON N8Y 1E9
519-966-4901

Description

EZ Trap EZT224 overflow switch with 3/4″ male thread is designed to thread into fitting on secondary drain pans, providing overflow protection.
Includes: 1″x 3/4″ male threaded street ell, float switch assembly, 72″ cable.

Packaging

IMPORTANT NOTES

1. Install in accordance with RectorSeal® instructions as well as all applicable local plumbing, drainage and electrical codes.
2. Insulation is required when trap is installed in unconditioned space where sweating can occur.

Kit Contents

• (A) 1″ x 3/4″ Threaded Slip Street Ell (1)
• (B) Float Switch Assembly (1)
• (C) 72″ Modular Cable (1) Red/Blue Service Label (1)

Overflow Switch Assembly Instructions

1. Screw Street Ell (A) into 3/4″ drain pan overflow outlet.

2. Press fit Float Switch Assembly (B) into 1″ opening at top of Street Ell (A). DO NOT USE GLUE.
   Check that Actuator Arm and Float moves freely inside Ell.

3. Press plug end of Modular Cable (C) into Float Switch Assembly (B).

4. Attach service & cleaning labels as indicated.

Note : Insulation is required when trap is installed in unconditioned space where sweating can occur.

Applications
Overflow switch that can thread into fitting on secondary drain pan.

Characteristics | Features

• Easy to install and maintain
• Float switch overflow protection.
• 4 Amp, 24 Volt

Note : Wiring diagram shown cuts power to thermostat when float switch operates to stop operation of the A/C unit. To inhibit mold growth during long absences, connect terminals into yellow cooling circuit so when float switch operates, condenser will switch off but fan will continue running.

Wiring Instructions

1. Turn off electrical power at main panel before installing EZ Trap switch.
2. An in-line fuse is necessary to protect the 24V circuit.
3. Connect Float Switch using wiring diagram. (above)
4. Test system for proper operation by lifting float.

Operating Procedure
Should blockage occur in the condensate drain line, the float will lift to stop operation. To reset, press center button on switch.

Limited Warranty

For more information on our product limited warranty, visit RectorSeal.com
Manufactured by
RectorSeal, LLC
2601 Spenwick Drive  Houston, TX 77055, USA 800-231-3345  Fax 800-441-0051  rectorseal.com
3255 Wyandotte St. East, Windsor, ON N8Y 1E9, 519-966-4901
A CSW Industrials Company. RectorSeal, the logos and other trademarks are property of RectorSeal, LLC, its affiliates, or its licensors and are protected by copyright, trademark and other intellectual property laws, and may not be used without permission. RectorSeal reserves the right to change specifications without prior notice. ©2022 RectorSeal. All rights reserved. R50706-0922

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>