NIE-TECH ZW1505 S2 Z-Wave Plus Power Strip with USB Charging Ports User Manual

NIE-TECH ZW1505 S2 Z-Wave Plus Power Strip with USB Charging Ports

Product Information

Specifications

• Model Number: ZW1505 VER. 3.0
• Z-Wave Signal Frequency: 908.40 MHz, 908.42 MHz, 916 MHz, 912 MHz, 920 MHz
• Power: 120 VAC
• Maximum Load: 15 A total (between 5 outlets)
• Maximum Load for USB ports: 2.1 A total (between 2 ports)
• Cord Length: 2 feet
• Range: Up to 100 feet line of sight
• Installation and Use: Indoor only

Product Usage Instructions

Installation

1. Plug the Power Strip into any standard grounded 110 V receptacle.
2. Do NOT connect any devices to the strip at this point.
3. Turn the power switch on (the RESET side) and click each of the channel’s control buttons to see if the LED indicators come on and off.
4. If the LED indicators don’t light up at all, please try a different receptacle.
5. If they’re still off, please make sure the power switch is on.
6. If the problem persists, contact our support team at ask@getzooz.com.

Before You Plug Anything In

If you are unsure whether your equipment can be safely controlled by the Power Strip, contact us at ask@getzooz.com.

Z-Wave Control

1. Plug the Power Strip into a grounded receptacle you’re planning to use it at (it doesn’t need to be close to the hub).

FAQ

Q: Can this product control appliance remotely?

A: Yes, this product allows Z-Wave on/off control of up to 5 electrical devices.

Q: What is the maximum load for the USB ports?

A: The maximum load for USB ports is 2.1 A total between the two ports.

Q: Does this product offer energy monitoring for each outlet?

A: Yes, this power strip provides energy monitoring for each of the 5 outlets.

FEATURES

• Z-Wave on/off control of up to 5 electrical devices
• On/off (charging/charged) reports from USB ports to the hub (no Z-Wave control) – turn off the charging device for best results
• Energy monitoring for each of the 5 outlets
• Built-in overload protection and ETL certification
• Z-Wave Plus signal repeater to extend network range
• S2 security protocol and the latest 500 Z-Wave chip for faster and safer wireless communication

SPECIFICATIONS

• Model Number: ZW1505 VER. 3.0
• Z-Wave Signal Frequency: 908.40 MHz,908.42 MHz,916MHz,912MHz, 920MHz
• Power: 120 VAC
• Maximum Load: 15 A total (between 5 outlets)
• Maximum Load for USB ports: 2.1 A total (between 2 ports)
• Cord Length: 2 feet
• Range: Up to 100 feet line of sight
• Installation and Use: Indoor only

CAUTION

• This is an electrical device – please use caution when installing and operating the power strip. Remote control of appliances may result in unintentional or automated activation of power.
• Do NOT use this Z-Wave device to control electric heaters or other appliances that produce the risk of fire, burns, or electrical shock when unattended.

INSTALLATION

• Plug the Power Strip into any standard grounded 110 V receptacle. Do NOT connect any devices to the strip at this point. Turn the power switch on (the RESET side) and click each of the channel control buttons to see if the LED indicators come on and off.
• If the LED indicators don’t light up at all, please try a different receptacle. If they’re still off, please make sure the power switch is on. If the problem persists, please get in touch with our support team: ask@getzooz.com

BEFORE YOU PLUG ANYTHING IN

• Make sure the load you are about to connect does NOT exceed 15 A in power. This Power Strip can hold up to 15 A in total. It means that the power of all appliances connected to your ZW1505 at a given time can NOT exceed 15 A.
• It doesn’t matter if this is just one device connected to one of the outlets or 5 small appliances plugged into all of the Strip’s outlets.
• Connecting heavy-duty equipment to this Power Strip will DAMAGE the device and may cause the connected appliance to malfunction. Do NOT plug washers, dryers, refrigerators, or motors over 1/3 hp to any of the outlets on the Power Strip.
• Not sure if your equipment can be safely controlled by the Power Strip? Just ask: ask@getzooz.com
• This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications.
• All non-battery-operated nodes within the network will act as repeaters regardless of vendor to increase the reliability of the network.
• This product features the latest Security 2 (S2) framework to remove smart home network hacking risks. This device supports the S2 unauthenticated security level with encrypted communication.

WARNING

• This product should be installed indoors upon completion of any building renovations.
• Before installation, the device should be stored in a dry, dust-and-mold-proof place.
• Do not install the Power Strip in a place with direct sun exposure, high temperature, or humidity.
• Keep away from chemicals, water, and dust.
• Ensure the device is never close to any heat source or open flame to prevent fire.
• Ensure the device is connected to an electric power source that does not exceed the maximum load power.
• No part of the device may be replaced or repaired by the user.

WARRANTY

This product is covered under a 12-month limited warranty. To read the full warranty policy or file a warranty claim, please go to www.getzooz.com/warranty

Z-WAVE CONTROL

1. Plug the Power Strip into a grounded receptacle you’re planning to use it at (it doesn’t need to be close to the hub)
2. ADD DEVICE to your hub Initiate inclusion (pairing) in the app (or web interface). Not sure how? Get step-by-step instructions for adding the strip to SmartThings, Vera, Hubitat, and other hubs here: www.support.getzooz.com
3. Finalize inclusion at the strip.

CLICK CH1 BUTTON 3 TIMES QUICKLY

All LED indicators will start flashing.

NEED SOME HELP? ask@getzooz.com

You will see 7 or 8 new on/off devices in your app: 5 channels for on/off control, 2 channels for on/off monitoring (USB ports reporting charging/charged status, no control), and possibly one master node to access and adjust advanced settings in, depending on the hub you’re using.

TROUBLESHOOTING

The Power Strip won’t add to your system. Try this:

1. Initiate EXCLUSION and click the CH1 button 3 times quickly.
2. Click the CH1 button 4-5 times quickly when adding it.
3. Bring the Power Strip closer to your hub, it may be out of range.
4. Double-check if the device is powered.
5. Get troubleshooting tips for your hub at www.support.getzooz.com

EXCLUSION (REMOVING / UNPAIRING DEVICE)

1. Bring the strip within direct range of your Z-Wave gateway (hub).
2. Put the Z-Wave hub into exclusion mode (not sure how to do that? ask@getzooz.com).
3. Press and release the CH1 button 3 times quickly.
4. Your hub will confirm exclusion and all of the channels (child outlets) and the main device will disappear from your controller’s device list.

FACTORY RESET

• If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To complete the reset process manually, click-click-click’n’hold the CH1 button for at least 10 seconds.
• All LED indicators will flash to confirm successful reset.
• NOTE: All previously recorded activity and custom settings EXCEPT for the kWh record will be erased from the device’s memory.

KWH RESET

• If you’d like to reset the kWh record for any of the outlets, just click the CH button next to the respective outlet 10 times very quickly. Network exclusion or factory reset will NOT automatically erase the kWh data.

ADVANCED SETTINGS

• Please refer to your controller’s user guide for advanced programming instructions as they are a little different for every software.
• Not sure where to start? Go to www.support.getzooz.com for detailed instructions on how to change the settings on SmartThings, Vera, and more. Or just email us: ask@getzooz.com

ASSOCIATION

• The Power Strip supports Group 1 for lifeline communication of on/off status to the Z-Wave gateway controller (hub).

CUSTOMIZE YOUR POWER STRIP

• You can adjust the frequency and threshold for power monitoring or change how the buttons and LED indicators behave on your Power Strip.
• Scan the QR code for a full list of parameters for this device and learn how to access them on your hub.

IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHE-THER IN AN ACTION IN CONTRACT, OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES. ZOOZ’S LIABILITY AND CUSTOMER’S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT ZOOZ’S OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS FROM ZOOZ’S DELIVERY, OR THE DATE FIXED FOR DELIVERY IN THE EVENT OF NONDELIVERY.

FCC NOTE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

References

• One moment, please...
• Home - Zooz Support Center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>