Hongzi HZ8801 Hair Salon Styling Chair User Manual
- June 7, 2024
- Hongzi
Table of Contents
HZ8801 PRODUCT MANUAL
Model# HZ8801
ATTENTION PLEASE READ THIS INSTRUCTION BEFORE USING THIS DEVICE.
NOTICE:
If your package is missing parts or you are having issues with the assembly.
please call us directly. Our customer service team will address any questions
or concerns you may have. Have ve this manual open and ready for reference.
SAFETY
To reduce the risk of injury when assembling & using the chair, follow these
precautions:
- Read all of these instructions before assembling and using your salon chair.
- It is helpful to have 2 people assemble and turn the chair upright after assembling.
- Do not over-extend the chair(0-150kg), creating the risk of falls or tipping the chair, and its occupant over, resulting in injury
PARTS & FEATURES
INSTALLATION INSTRUCTION
First: installation hydraulic pump to the base
Parts needed: Base + pump + foot bar Step 1:Insert threaded bolts on the
bottom of Pump into holes on top of Base. Tighten 6 locking nuts onto threaded
bolts. (Easiest when set on the side, supported by a sturdy object.) Step 2:
Place assembled Base & Pump on the floor. Use Allen Wrench to loosen the
screws in the crossbar. See photo beside. Insert Foot Bar into the holes of
the crossbar. (May require slightly squeezing ends of Foot Bar towards each
other, and some maneuvering for the bar ends to go into place.)
Step 3. Tighten the set
Second: Install the tray of the chair to the bottom of seat cushion
Parts needed: seat
cushion + tray of chair
Step 1 . Rmove the 4 fixing bolts which pre-fixed on the bottom of the seat
cushion.
Step 2 install the tray of the chair to the bottom of the seat cushion by the
4 fixing bolts given from the seat cushion.
Please follow up the diagram beside
Third: Install backrest to the seat cushion
Parts needed: seat cushion + backrest
Step 1. Remove the 3 fixing bolts which Pre-fixed on the seat cushion.
Step 2. Install the backrest to the seat cushion by the 3 fixing bolts given
from the seat cushion.
Please follow up the diagram beside
Fourth: Install hand rests to the installed seat cushion & backrest
Parts needed: 2 handsets + installed seat cushion & backrest + 4 Plastic
covers of bolt
Step 1: Remove 4 long bolts which pre-fixed on the backrest and seat cushion.
Step 2: Install 2 handrest to the seat cushion & backrest by the 4 long bolts
given from the seat cushion and backrest.
Fifth: Install the installed seat to the installed base &puom
Parts needed:
Installed seat + installed base&pupm
Step 1: Place the installed seat onto the hydraulic pump(please note the pin
on the pump toward the gap of the pump joint)
Please follow up the diagram beside.
Sixth: Install foot-rest to the Leg-rest
Parts Needed: Leg support + Footrest
Step 1:Remove 2 bolts which pre-fixed in the footrest
Step 2:Install the leg-rest to the leg-rest by the 2 removed bolts and tighten
them.
Please follow up the diagram beside.
Seventh: install the installed footrest on the seat
Step 1: Remove 2 bolts which pre-fixed in the seat
Step 2: Install the installed footrest to the seat with the 2 given bolts and
tighten them
Please follow up the diagram beside.
OPERATING THE CHAIR
• Step down on the Foot Bar repeatedly to raise the chair.| 
---|---
• Step down and hold the Foot Bar to allow the chair to lower.
• Hold the Foot Bar up to keep the chair still.
• Do not over-extend the chair. creating the risk of falls or tipping the
chair and its occupant over. resulting in injury.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>