Royal Sovereign HCE-220 Digital Ceramic Tower Heater Owner’s Manual

: June 7, 2024
: Royal Sovereign

Royal Sovereign HCE-220 Digital Ceramic Tower Heater Owner’s Manual

INTRODUCTION

Thank you for choosing Royal Sovereign to provide you and your family with all of the “Home Comfort” requirements for your home, apartment, or office. This Heater can be set-up in just
minutes and can be easily moved from room to room. It is a multi-functional room air comfort system that offers you Heating and Fan Only modes. This manual will provide you with valuable information necessary for the proper care and maintenance for your new heater. Please take a few moments and read the instructions thoroughly. If properly maintained, your heater will give you many years of trouble free operation.
Because our products are subject to continuous improvement, RS Canada reserves the right to modify product design and specifications without notice and without incurring any obligation. E&OE

Precautions for use

• Do not block or cover air outlets.

Electrical Specifications and Power Cord

Check to ensure that the electrical service being used is adequate for the model you’ve chosen. The electrical rating of your new heater is defined on the serial sticker on the unit. Please refer to the rating when checking electrical requirements to ensure they meet the electrical codes of your location.

Do not use this appliance if it malfunctions or is dropped or damaged in any manner.
Do not use outdoors. Do not place on or near a hot gas, electric burner, a microwave, or a heated oven.
To protect against fire, electric shock or injury, do not place cord, plug, or appliance in water or other liquid.
The wrong use conflicting with the safeguards voids the customer of the right for warranty service.
Do not modify any part of this product.
Do not insert any objects into the product or block the airflow in any way.
Ensure that the power supply you use has an appropriate voltage rating.
If the electrical outlet you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, you should have a qualified electrician install the proper outlet.
Do not use this unit with any extension cords or adapter plugs.
If the cord or plug is damaged in any way, please call the Royal Sovereign Service Department
Turn the unit off and unplug, when cleaning the heater or when the heater will not be used for an extended time period.
When overheating should occur the built-in overheating safety device will shut the appliance off.

General Use

Do not block air outlets with any obstacles.
Do not insert any objects into the heater.
Do not pour water on the housing or control panel.
Do not place heavy items or sit on the heater.
Never pull or damage the power cord in any way.
Don’t let your children use the appliance.
The repair of the appliance must be performed by a professional. Mistakes in repair are dangerous and can bring great hazard to the user.

Description

ON/OFF Rocker Switch
Filter
Power Cable
LED Display
Ventilation
Base
Remote

OPERATION

Using The Remote
NOTE: Pull away the small plastic tab located on the bottom of the Remote (7) to activate the battery.
The Remote has 6 functions:
NOTE: The functions are non-effective when the heater is in standby mode except for the Power Button.

POWER – To power the unit on/off (in between standby and on).
NOTE: This will only work when the ON/OFF Rocker Switch (1) is on.
NOTE: When the Heater is powered off, the fan will run for approximately 60 seconds before powering off completely.
MODE – Changes the power settings:
• Fan-only • Low power- 750W • High power – 1500W
TIMER – The timer function allows you to set the length of operation for up to 9 hours for automatic switch off.
Pressing the ‘TIMER’ button increases the length of operation by 1 hour each time the button is pressed.
Once the timer has been set, it will count down the hours in 1 hour intervals; when the time reaches zero, the Heater will
automatically switch off and enter standby mode.
Pressing the ‘TIMER’ button once more when the display shows 9 hours will reset the Heater to run continuously.
OSCILLATING – Switches the oscillating function on or off.
UP – Increases the temperature in 1°F increments.
When increasing the temperature using the button (circled above), press the button repeatedly rather than holding your finger over it for a prolonged period. Holding your finger over the button for more than 2 seconds will set the LED Display to show the temperature in °C. Should this happen, simply hold your finger on the button for 2 seconds to revert back to °F.
DOWN – Decreases the temperature in 1°F increments. Using The Heater
Use the ON/OFF Rocker Switch (1) on the rear of the Heater to switch it on. Press the ‘POWER’ button and the Heater will switch on from standby and the LED Display (4) will show the room
temperature. The Heater will begin to heat up to the preset temperature of 77°F.
NOTE: If the room temperature is 2°F higher than the preset temperature, then only the fan will operate. The Heater will switch back on again once the room temperature drops 2° to 3°F. If the Heater is not operated for 3 seconds, the LED Display will show the room temperature. The Heater will cycle on and off to maintain the preset temperature. This is not a fault with the appliance.
To set the heating power, or to use the fan-only mode, press the ‘MODE’ button to cycle through low heat, high heat or fanonly settings.
To set the temperature, press the or buttons to increase or decrease to the desired temperature. The LED
Display will show the set temperature for 3 seconds.
Once the room reaches the set temperature, the Heater will cycle on and off to maintain this temperature.
To set the set auto off, press the ‘TIMER’ button until the desired time has been reached. The LED Display will show for up to 3 seconds, then revert back to displaying the room temperature.

LED DISPLAY

SAFETY FEATURES

This Heater is fitted with an overheat protection switch (thermal cut-out) which will power off the appliance automatically in case of overheating. Should this occur, unplug the appliance and allow to cool fully for approximately 30 minutes.
Follow the operation instructions to restart the appliance after removing the source of the overheating (poor ventilation, item covering the heater etc.). The Heater should function normally. Should the problem persist, please contact Designer Habitat Customer Services. To avoid damage and to regulate the temperature, this Heater is fitted with a thermostatic safety device. The safety device will activate and cut out the power to the Heater once a certain temperature is reached. The Heater will start again once the temperature has lowered. The Heater is also fitted with a tip switch which will cut off the power to the Heater if it is knocked over. Should this happen, disconnect at the mains and allow to cool fully before attempting to move the Heater. Inspect the Heater for damage. If – and only if – the Heater is free from damage, plug back into the mains. The Heater should function normally.

CLEANING AND CARE

IMPORTANT: Turn off the Heater. Switch off the ON/ OFF Rocker Switch and disconnect from the power socket. Wait for the Heater to be completely cool before cleaning. Vacuum-clean air vents and grilles to remove dust from these areas.
To remove dust on external surfaces, wipe the Heater with a damp (not wet) lint-free cloth rinsed in hot soapy water only.
CAUTION : Do not use any harsh detergents or abrasive cleaners.
WARNING! Do not spray with any liquids or submerge in liquid or water.
WARNING! Do not attempt to clean the interior of the Heater. Do not attempt to open the casing at any time. There are no
user-servicable parts.
Remove the Filter (6) and clean regularly. To remove the Filter, locate the 3 small screws on the rear of the Heater, remove
the Filter Cover and Filter and rinse the Filter using clean water. Leave to dry completely before replacing.
CAUTION: Ensure the Filter is completely dry before returning it to the Heater. Failure to follow this instruction could
damage the product, invalidating any warranty.

STORAGE

Store the Heater carefully in a dust-free area during the off season. It is ideal to store the Heater in the box in which it was supplied.
Neatly wind the cord of the Heater to prevent damage.

TROUBLESHOOTING

Problem	Solution

The heater will not power on

| Ensure the Heater is switched on and connected to themains power. Activate the ON/OFF Rocker Switch. Ensure the Base is fitted and the Heater is upright.

The heater is not heating up

| Check that the Heater is plugged in at the mains outlet.
Ensure that the set temperature is higher than the room temperature on the display.
Make sure that the Heater has not gone into overheat protection mode (see ‘Safety Features’). The vents may need cleaning.
The heater becomes damaged| Discontinue use and contact Designer Habitat Customer Services.

SPECIFICATIONS

Model	HCE-220
Voltage/Frequency	AC 120V~60Hz
Input power	750W / 1500W
Dimension (w × h × d)	8.7in. (W)× 6.5 in. (D) × 22.4in. (H)
Weight	7 lbs

WARANTY

Royal Sovereign warrants each heater to be free from defects in material and workmanship. Our obligation under this warranty is limited to the repair or replacement, free of charge, when delivered to an authorized Royal Sovereign service center, of any defective part(s) thereof, other than parts damaged in transit. This warranty is in effect to the ozzriginal purchaser, for a period of one year from the date of purchase and is not transferable. This warranty shall apply only if the heater is used in accordance with the factory provided instructions which accompany it.

EXCLUSIONS

This warranty excludes and does not cover defects, malfunctions or failures of your Royal Sovereign Heater, caused by repairs by unauthorized persons or service centers, mishandling, improper installation, modification or unreasonable use including incorrect voltage, acts of God, or failure to provide reasonable and necessary maintenance. This warranty is in lieu of any and all expressed warranties. In no event shall Royal Sovereign be liable for consequential or incidental damages.
This limitation would not apply if you live in a location that does not permit the exclusion of limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.