Royal Sovereign ARP-912 Portable Air Conditioner Owner’s Manual
- June 4, 2024
- Royal Sovereign
Table of Contents
Owner’s Manual
Portable Air Conditioner
ARP-912
Royal Sovereign International, Inc. Please read and retain these
instructions.
To register your product, please go to
www.royalsovereign.com
Thank you for purchasing the Royal Sovereign Portable Air Conditioner, ARP-912 / ARP-914. This manual will provide you with safety information, instructions for optimal use, and proper care and maintenance for your product. Please read this manual carefully before operating.
SAFETY INSTRUCTIONS
This appliance follows these safety precautions to reduce the risk of fire, electric shock, or injury.
WARNING
Electrical Safety
- For your safety, this appliance should be properly grounded on a level surface indoors.
- The appliance should be placed near an electrical outlet so that the outlet is easily accessible.
- Make sure the voltage meets the appliance’s electricity requirements (115-120V/60Hz).
- Do not connect this machine to an outlet having the electrical ratings below or above this machine.
- In case of any abnormality, be sure to turn off the machine, disconnect the plug, and contact Royal Sovereign Customer Service.
- Do not operate if the electrical plug or power cord is damaged. If damaged, call Royal Sovereign Customer Service for repair/replacement.
- Do not under any circumstances alter the electric plug.
- Do not place heavy items on the plug or cord.
- Do not plug this cord into a loose electrical outlet.
- Only plug the appliance into a properly installed, grounded 3-prong outlet.
- If the electrical outlet you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, you should have a qualified electrician install the proper outlet.
- Do not share the electrical socket with other appliances.
- Do not use this appliance’s adapter plug or extension cord.
- Never attempt to turn off this machine by disconnecting the plug.
- When plugging or unplugging, keep your hands dry.
- Always grasp the plug when plugging or unplugging the appliance. Never unplug by pulling on the cord.
- Do not pull on the power cord while moving the unit.
- This unit uses a plug with a built-in fuse. Conduct a Power Plug Check (see Operation page 8) before use to confirm normal operation.
- Turn the unit off and unplug when; cleaning the air conditioner, removing the filters, and not using the air conditioner for an extended time period.
Read & Fully Understand This Owner’s Manual Before Using This Machine.
SAFETY INSTRUCTIONS
This appliance follows these safety precautions to reduce the risk of fire, electric shock, or injury.
WARNING
Operational Safety
- Install the air conditioner according to the installation instructions supplied (Installation pages 6-7).
- Do not block air outlets or intake with obstacles.
- Do not insert any objects into the air conditioner.
- Do not place heavy items or sit on the unit.
- Do not place flammable or chemical substances near the unit.
- Do not place this machine near heating appliances.
- Do not splash or pour water on the housing or control panel.
- To prevent the water from freezing, do not use this machine and the drain hose at a temperature below 41°F (5°C).
- Make sure the rubber drain plug is securely plugged into the drain port on the back of the unit at the bottom to prevent water leaks.
- Drain the unit before moving the air conditioner or storing the unit.
- Do not operate the unit with the back cover removed.
- Do not use this machine outside. Exposure to direct sunlight or rain may result in overheating, electric shock, and fire.
- Do not modify any part of this product.
- Do not operate this appliance for any other purpose other than its intended use.
- This appliance is not designed for use by young children. Young children should be supervised to ensure that they do not play with or climb on the unit.
Read & Fully Understand This Owner’s Manual Before Using This Machine.
PRODUCT VIEW
1. Display panel
2. Air outlet
3. Caster wheels
4. Air filters| 5. Exhaust duct (with connectors attached)
6. Cord management hook
7. Drainage port
---|---
| POWER
---|---
| TIMER
| AUTO
| COOL
| FAN
| CHILD LOCK
| DEHUMIDIFY
| SWING
| SPEED
| +
| –
INSTALLATION
Accessories Included
- Window seal plate
- Exhaust duct connectors (2)
- Exhaust duct
- Remote control
- Drainage hose
- Instruction manual
| When the automatic mode is selected: the front display window is displayed
on the right
---|---
| When the cooling mode is selected: the front display window is displayed on
the right
| When the ventilation mode is selected: the front display window is displayed
on the right
| When dehumidification mode is selected: the front display window is
displayed on the right
NOTE : To prevent damage after moving, unpack your new portable air
conditioner and let the machine stand upright for a minimum of 2 hours before
operating.
Part 1: Placement
- Place the air conditioner on a flat surface and near a power supply outlet at least 8 in. (20 cm.) away from any wall or object that could block the airflow (See below).
- Socket wiring should be in accordance with the local electric safety requirements.
Part 2: Exhaust Hose Installation
- The two exhaust duct connectors tighten on the ends of the exhaust duct (See Fig. 1).
- Slide the square side of the exhaust duct connector into the opening at the back of the air conditioner (See Fig. 2 and Fig. 3).
- The exhaust hose can extend up to approximately 59 in. (150 cm.).
Part 3: Window Seal Plate Installation
- The window seal plate can be installed horizontally or vertically. The window seal plate can fit in windows with a minimum width of 23.5 in (60 cm.) and a maximum width of 59 in. (150 cm.).
- Open the window and place the window seal plate on the inside edge of the window.
- Adjust the window seal plate to the width of the window. Once secure, close the window.
- Connect the oval side of the exhaust duct connector to the window seal plate.
PRODUCT OPERATION
BEFORE PLUGGING IN THE UNIT TO A POWER SOURCE:
- Let the appliance stand upright for a minimum of 2 hours. This will reduce the chance of malfunction in the cooling system.
- Check to make sure the rubber drain plug is securely plugged into the drainage port on theback of the unit at the bottom to prevent water leaks.
- Check to make sure the exhaust hose has been installed properly (See Installation page 7).
- Check to make sure that the air conditioner has been properly vented out the window (see installation page 7).
Conduct a Power Plug Check:
- Press the RESET button on the power cord.
- Plug the cord into an electrical outlet.
- Press the TEST button on the power cord. The RESET button should pop up.
- Press the RESET button for use.
- Do not use the air conditioner if the test fails. The green light on the power cord will turn on if the plug is working properly.
Note : IF YOU TURN THE AIR CONDITIONER OFF AND IMMEDIATELY RESTART IT,
ALLOW 3 MINUTES FOR THE COMPRESSOR TO RESTART COOLING. IN THE EVENT OF A POWER
FAILURE, WAIT 3 MINUTES BEFORE RESTARTING THE UNIT.
ATTENTION : THE UNIT IN THE UNITED STATES IS SET TO FAHRENHEIT. THE UNIT
CANADA IS SET TO CELSIUS.
Remote Control
- All functions can be accessed from the remote control. A CR2025 battery is required for
operation. The battery is included.
Child Lock Function:
- This button is on the remote control only. When pressed, this function locks the air conditioner into the mode it is currently in. When in lock mode you cannot change modes from the display or remote control until it is unlocked. Unlock by pressing the lock button again.
Touchscreen Control Panel:
Icon | Description |
---|---|
Press this icon to turn the machine on and off. | |
Press this icon to switch between operating modes: fan, auto, and cool. | |
Press this icon to lower the set temperature or 24-hour timer. | |
Press this icon to raise the set temperature or 24-hour timer. Long press |
this key for 5 seconds to show the current room temperature.
| Press this icon to set the wind speed of the machine. The first press sets
the high speed, second press sets the low speed.
| Press this icon to operate the timer. When the machine is on, use the timer
to set a time-off. When the machine is off, use the timer to set the time-on.
| Press this icon to turn on the dehumidification mode.
| Press this icon (swing) to turn on the vertical oscillating air vent.
Boot State:
- When you select a mode, the machine will enter the boot state. The front display, as well as the indicator light of the mode selected, will blink for a few seconds to allow the machine to process the selection. Once the machine has processed the change, the indicator light will turn solid and the new mode will begin.
Fan Operation:
- In the boot state, press the mode icon to switch to fan mode. The front display, as well as the indicator light, will blink for a few seconds when selected and turn solid when confirmed.
- In fan mode, the upper blower works and the compressor does not work.
- Press the wind speed icon to switch between high and low wind speeds.
Auto Mode:
- In the boot state, press the mode icon to switch to automatic mode. The front display, as well as the indicator light, will blink for a few seconds when selected and turn solid when confirmed.
- When the machine is powered on for the first time or if the machine has been off for more than 30 minutes, the machine enters automatic mode by default.
- When switching to automatic mode from other modes or from powering on the air conditioner (first time or when off for over 30 minutes), the machine will automatically set to the following:
- If the room temperature is > 75°F (24°C) auto set to cooling mode
- If the room temperature is > 72°F (22°C) and < 75°F (24°C) auto set to fan mode
- If the room temperature is < 72°F (22°C) auto set to single cold type ventilation
- Once in automatic mode, the room temperature will change, while the set mode will remain the same. The set mode will not change until the automatic mode is complete.
Cooling Operation:
- In the boot state, press the mode icon to switch to cooling mode. The front display, as well as the indicator light, will blink for a few seconds when selected and turn solid when confirmed.
- Press the increase or decrease icons to set the desired temperature. The temperature range is from 59-88°F (15-31°C). The front and top digital displays will show the current set temperature.
- Press the wind speed icon to switch between high and low wind speeds.
- For optimal operation, shorten the length of the air duct and keep it from direct sunlight.
Oscillating Air Vent:
- In the boot state, press the swing icon. The front display, as well as the indicator light, will blink for a few seconds when selected and turn solid when confirmed.
- In this mode, the air vent louvers will automatically swing up and down.
- Press the swing icon again. The indicator light will turn off when selected and the louvers will stop swinging.
Dehumidify Mode:
- In the boot state, press the dehumidification icon. The front display, as well as the indicator light, will blink for a few seconds when selected and turn solid when confirmed.
- In the dehumidify mode, the fan runs at low speed and the temperature is not adjustable.
- Do not use dehumidify mode when the temperature is lower than 59°F (15°C).
Timer
- When the air conditioner is on, press the timer icon and select a desired off (shutdown) time through the increase and decrease icons (+ / -). The off timer can be set for any time from 0 to 24 hours. Press the timer icon again to show the preset shutdown time on the control panel and front display.
- When the air conditioner is off, press the timer icon and select a desired (startup) time through the increase and decrease icons (+ / -). The on a timer can be set for any time from 0 to 24 hours. The control panel and front display will show the time remaining until startup.
- Once the desired time is selected, wait 3 seconds and the air conditioner will automatically accept the setting.
MACHINE MAINTENANCE
WARNING : Before maintenance, turn the power switch off and disconnect
the power cord from the wall.
Drainage
The internal water tank in the air conditioner has a water level safety
switch. When the water level reaches or exceeds an anticipated height, the
buzzer alarm will ring 6 consecutive times, each time interval of 1 second.
The machine will then enter E4 water full protection mode and be shown on the
display. In E4 mode the machine will stop the refrigeration and the
compressor. In order for the machine to resume operation, it must be drained.
To drain manually:
- Turn off the power to the unit and unplug.
- Place a water tray under the drainage port at the bottom of the unit to collect water.
- Remove the rubber drainage plug.
- Replace the plug, when drainage water stops flowing.
For continuous drainage into a floor drain:
- Turn off the power to the unit and unplug.
- Remove the rubber drainage plug from the drainage port at the bottom of the unit.
- Attach the drainage hose to the drainage port. The drainage hose is approximately 40in.(101cm.).
- Place another end of the drainage hose into a floor drain.
- Replace the rubber drainage plug after operation to prevent leaks.
Cleaning the unit
- Turn off the power to the unit and unplug.
- Wipe down the unit with a soft, dry, or damp cloth. A mild detergent can be used.
- Never use a volatile substance such as gasoline or abrasive cleaners.
- Do not splash water onto the unit.
WARNING : Before maintenance, turn the power switch off and disconnect
the power cord from the wall.
If the unit will not be used for a long time:
- Drain the air conditioner manually using the drainage port (See Drainage page 12).
- Remove the battery from the remote control before storage.
- Clean the air filters.
- Cover with plastic or return it to the original carton.
Cleaning the air filters
The filters should be cleaned about every 2 weeks to maintain proper airflow.
- Grasp the formed handle of the filter and pull it up, removing it from the evaporator.
- Use a brush attachment with a vacuum cleaner to clean the air filters.
NOTE: Failure to keep the air filters clean will result in poor circulation. DO NOT operate the machine without the filters.
TROUBLESHOOTING
In case of problems, first, turn off the air conditioner and disconnect from the source of electricity.
Symptom | Solutions |
---|---|
The machine is not running ning or only running on the mode | Reset the power |
plug. Wait 3 minutes and try to run the unit again. Securely confirm that the
unit is plugged in.
Make sure the appliance voltage meets the electricity requirements. Check to
see if the water indicator light is on. If full, drain the water tank (See
Drainage page 12).
Check to see if the 24-hour timer is set to off.
Not cool enough| Make sure all windows and doors in the room are closed.
Connect the exhaust air hose tightly and make sure that it can function
properly. Keep it as short and free of curves as possible to avoid
bottlenecks.
Make sure all air inlets and outlets are not blocked. If they are, clear the
obstruction.
Remove all heat sources from inside the room.
Decrease the set temperature.
The air filter may be blocked by dust, so clean the air filter.
The machine is noisy or vibrating during operation| Place the unit on a flat,
level surface.
Make sure that the unit is not touching any other objects.
The machine often starts or stops| Make sure that you are using the correct
supply voltage from a suitable power source.
Correct the placement of the exhaust hose
E2 Code| The room temperature sensor is abnormal. Contact for repair.
E3 Code| The indoor and outdoor sensor is abnormal. Contact for repair.
E4 Code| Full of water. Empty tank.
E5 Code| The outdoor coil sensor is abnormal. Contact for repair.
NOTE : For all replacements and repairs that need to be made, contact Royal Sovereign Customer Service at +1) 800-397-1025
SPECIFICATIONS
MODEL | ARP-912 |
---|---|
Cooling Capacity | 12,000 BTU ASHRAE |
7,500 BTU DOE
Room Size (Sq. ft.)| Up to 450
Voltage / Frequency| 115-120V / 60 Hz
Standard Cooling Input Power| 1250W
Rated Cooling Current| 11.3 A
Operating Sound Level| 5 56 dB
Dehumidifier Capacity| 45.6 Pints (21.6 L) per Day
Air Flow Volume| 340 m3h
Fan Speeds| 2
Fan Speed Level| Low: 950 pm high: 1200 rpm
Refrigerant| R410A
Temperature Setting| 59-88 °F (15-31 °C)
Certification| cETLus
Unit Dimensions (W x D x H)| 15.94″W x 12.4″D x 25.98″H mm x 315 mm x 660 mm
Unit Weight| 55.12 lbs. / 25 kgs.
ONE-YEAR LIMITED WARRANTY
Royal Sovereign International, Inc. warranties this product to be free from
defects in material and workmanship to the original purchaser only as outlined
below.
Parts : Replacement of defective parts for 1 year from the date of
customer purchase.
Compressor : 3-year warranty from the date of customer purchase. Royal
Sovereign will supply a replacement compressor (parts only), free of charge.
Labor : 1 year from the date of end-user purchase.
This warranty only covers products that are properly installed, properly
maintained, and properly operated in accordance with the instructions
provided. This limited warranty does not cover any failures or operating
difficulties due to normal wear and tear, accident, abuse, misuse, alteration,
misapplication, improper installation, or improper maintenance and service by
you or any third party.
Returned products will not be accepted without a Return Authorization number.
To request a Return Authorization number, please visit us at
www.royalsovereign.com. All transportation
costs for the return of damaged products or parts will be the responsibility
of the purchaser. Return the defective products, in original packaging, to the
address below.
Royal Sovereign International, Inc. requires reasonable proof of your date of
purchase from an authorized retailer or distributor. Therefore, you should
keep your receipt, invoice, or canceled check from the original purchase. The
limited warranty shall be limited to the repair or replacement of parts that
prove defective under normal use and service within the warranty period.
Royal Sovereign International, Inc. (and its affiliated companies) SHALL HAVE
NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL,
INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Some states do not
allow the exclusion or limitation of incidental or consequential damages so
the above exclusion and limitations may not apply to you.
ROYAL SOVEREIGN INTERNATIONAL, INC.
2 Volvo Dr., Rockleigh, NJ 07647 USA
TEL: +1) 800-397-1025
Email: info@royalsovereign.com| RS
INTERNATIONAL CANADA INC.
191 Superior Blvd, Mississauga Ontario L5T 2L6 CANADA
TEL : +1) 905-461-1095 TF # : +1)
866-961-6673
FAX : +1) 905-461-1096
www.royalsovereign.ca
---|---
For product support and warranty questions, please visit us at
www.royalsovereign.com/customer-
support.html
Documents / Resources
|
Royal Sovereign ARP-912 Portable Air
Conditioner
[pdf] Owner's Manual
ARP-912, Portable Air Conditioner, ARP-912 Portable Air Conditioner
---|---
|
Royal Sovereign ARP-912 Portable Air
Conditioner
[pdf] Owner's Manual
ARP-912 Portable Air Conditioner, ARP-912, Portable Air Conditioner, Air
Conditioner, Conditioner
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>