JVC Waterproof Bluetooth Speaker User Manual

: June 7, 2024
: JVC

Table of Contents

Waterproof Bluetooth Speaker
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Waterproof Bluetooth Speaker

User Manual

Using the Hands-Free Function

When a smartphone is connected to your speaker follow the steps below to take calls hands-free.

Press” “to pick up the call.
Press and hold” “for 2 sec to reject the call.
During a call: Press” “again to hang up the call.

Troubleshooting

Problem	Solution

The speaker doesn’t connect
to device|

Speaker needs to be connected/re-paired to
device

A tone is heard every few
seconds|

Speaker needs to be charged

Bluetooth connection does
not work up to 10 metres.|

Avoid operating the wireless speaker in areas
of strong electromagnetic interference,such
as near induction cookers, large power fans,
motors, etc.
Move the speaker closer to your
Bluetooth-enabled device.
Fully charge the speaker and try again.

The speaker will not power on|

Speaker needs to be charged

The speaker sound distorts at
high volume.|

The device’s volume needs to be lowered

Introduction

Use the JVC Waterproof Bluetooth Speaker paired with smartphones, tablets, or other devices to stream music and enjoy hands-free phone calls. For best results, please read this user manual carefully before first use.

Important Waterproof/Safety Information

This speaker is IP67 rated. This means that the speaker can be submerged under water (up to 1 metre depth) for short periods of time (up to 30 minutes). The charging port must be securely closed before using the speaker in a wet environment. Make sure the speaker is completely dry before connecting the charging cable.

Specifications

Loudspeaker: 4 5W
Built-in Battery:Li-ion 600mAh
Dimensions: 102x93x43 mm
SNR:80± 3dB
Bluetooth distance: up to 10m
Charging Time: 2-3 hours
Weight: 160 g
Speaker Diameter: 45 mm
Charging: DC5 V, 500mA

Package Contents

1. Bluetooth Speaker

2. USB Charging Cable

3. User Manual

Important Safety Precautions

Please read all instructions carefully and retain for future reference. When using the unit, basic safety precautions should always be followed, including the following:

Keep this product and its charging cable away from excessive heat.
Do not operate this device with a damaged cable or after it has malfunctioned or has been damaged in any manner.
Do not disassemble your device No user-serviceable parts inside.
This product is not a toy. Children should be supervised to ensure that they do not play with the appliance.
Do not expose batteries to heat or fire as they may explode.
Do not dispose of batteries in your household waste. Contact your local council for information on disposal or recycling.

Charging Your Speaker

Connect one end of the included USB Charging Cable to the Charging Port on your speaker. Then plug the other end of the USB Charging Cable into a suitable USB port on your computer to recharge your speaker’s internal rechargeable battery. Please note: The internal battery of your speaker takes approximately two hours to charge when completely drained.
When charging, a red LED light will illuminate to indicate that the unit is charging. The red light will turn off when your unit is fully charged.

A Quick Look at Your Device

Previous: Press and hold to access the last track in a playlist.Press to lower the volume.
Phone: Press this button to activate the speaker phone function. When music is playing, press to play or pause a track.
Next: Press and hold to access the next track in a playlist.Press to increase the volume.
Charging Port You can plug one end of the included USB Charging Cable into this jack, while plugging the other end into a USB port on your computer in order to charge your speaker’s built in lithium battery. You can also use a suitable USB adaptor for charging.
Important: Make sure the unit is completely dry before charging.
ON/OFF Switch Press and hold the” “to switch the unit on. Press and hold the” “again to switch the unit off.

Understanding the LED Status Lights
When Charging Your Speaker
Solid red LED = Charging No red LED = Charge is complete

When Pairing Your Speaker to a Bluetooth-enabled device

Rapid blinking blue LED: Not connected (ready to pair) Solid blue LED: Connected

Pairing Bluetooth-enabled devices to Your Speaker

In order to pair your Bluetooth device (smartphone/tablet etc.) to your Speaker for the first time, follow the steps below:

Make sure the wireless audio source is held within three metres of your speaker.
Press and hold the ” ” switch on your speaker to power on. The LED light will blink blue to indicate that you have entered pairing status.
Go to the setting menu of your wireless audio source. Please refer to the user manual of your wireless audio source for more information.
Search the devices and select “XS-N1129”.
Once paired, the blue LED light will be solid and you can use your speaker to listen to audio from your wireless sound source.