CoralBox Reverse Nano Pump User Manual

Reverse Nano Pump User’s Manual

CoralBox wavemakers are specifically engineered as the perfect equipment to simulate the natural sea environments.
RN-1 pump is a very compact propeller pump using innovation and high technology solutions to provide natural environments for different sea inhabitants in aquariums, fish tanks, or ponds. The excellent design, including the compact housing and the magnet holder, permits 3D flow directions and simple mounting at every point of aquarium walls.
Before assembling and operating correctly, please read the user manual carefully.

Function Overview

1. The unique control system allows operating with different types of waves and multiple functions, which can generate different wave patterns according to different needs.
2. Wireless controllers allow synchronizing operation among waves One main controller can remotely control several sub-controllers.
3. Low voltage DC electronic pump with variable frequency provides a safe environment for users.
4. Easy operation to achieve the multiple sea moving patterns
5. Flow direction can be adjusted by different operative modes, as needed.
6. A large range of voltage input(AC100~240V 50/60Hz) allows to operate in various power systems and prevent the impact on waves shapes.

Assembly and installation Notes

Suitable for most sizes of fish tanks and ponds, up to 15mm glass wall thickness.
Caution!The danger of injury! Pay attention to your fingers when locating the magnet due to the strong attractive power.

1. Separate the external magnet from the pump package. Locate the pump in the selected position inside the tank on the internal side of the glass wall. Locate the external magnet on the external side of the same glass wall and slide it up to the pump position. Ensure that the aquarium glass is free from algae inside and is dry and clean outside.
2. If the controller has to be stuck on the tank, peel off the protection paper from one side of the bi-adhesive tape and past it on the backside of the controller. Peel off the second protection paper and locate the control in the selected position.
3. Connect the pump to the controller by means of the 3-pins Insert the adapter plug to the controller and connect the power unit to the power supply source.
4. Start controller programming.

Operation and Function

Buttons and Functions of LED Display Controller.
Mode/Night : Press the button to select different modes: F1, F2, F3, F4, F5, F6 F7and enter the Night mode by long hold-down the button.
Freq/reverse : Press the button to change the Frequency and long hold the button to change to Reverse mode.
WI-LE/Reset : Press the button to select Master control” M”, “S” for Slave,” N” for Standalone. unit Hold down the Reset key for 3 sec. to reset the controller unit.
Arrow keys : 10Mins Feed / 20Mins Feed or move position.

Attention : If the pump operates in Night Mode, any other mode/feeding is disabled until exit from the Night Mode Be careful: Make sure to switch off the main switch of the controller before plugging the controller with a DC power supply or plus controller with a powerhead block.
Technical data

Name

| Flow Rate| Energy Consumption| Voltage / Frequency| Operating Tension| Cable Length| Dimension| Outlet Nozzle diameter
---|---|---|---|---|---|---|---
Coral Box WaveMaker RN-1 pump| 1500~10000L
(396~2642gal/h)| 25W| 110/240V 20/60Hz| 24V| 1860mm (6.1feet)| 78x72x 52mm (0.26 x 0.24 x

0.17 feet)

|

70mm (0.23feet)

Technical data

| F1:Stream Mode One or more pumps can operate at the same time, inconstant flow.  constant flow. ** Press o change frequency Press to change the flow
---|---
| F2:Pulse Mode One or more pumps can operate at the same time, in pulse flow. Pulse the wave by time/flow frequency. Nature  Mode(LPS) Reef
Mode(SPS)Press to change frequency Press to change flow
| F3:Shift to Wave Mode Shift flow in cycles, Pump A run, Pump B stop; Pump B run, Pump A stop Need have 2 Pump with WIFI  master and slave to run Press to change frequency press to change the flow
| F4:Nature Mode The power level changes between 30%~100%  making a natural flow. Press to change frequency Press to change the flow
| F5:Reef Mode Power of flow is changing in a random mode in volume and time. This is the best mode for corals Press to change frequency Press to change the flow
| F6:Timer Mode Six different operative modes can be set in this mode. For example, the first set of 9 a.m to 10 a.m stream mode, the second set of 10 a.m to p.m pulse mode.
| F0: Stop Mode Only work with timer mode. This mode Stops the Pump from running in the programmed time slot.
| F7: Reverse Mode** Clockwise pump. The pump uses the opposite direction of the water flow to improve the cleaning of your tank. Press to chang frequency Press to change flow.

How to Set the Timer?
First, you need to change Function to the F6: Timer mode
Press to switch timer program and input, press to move position.Press to adjusted the Real Time/Schedule/Timer/Mode.

Ⅳ.Warnings

• Do not operate the pump outside water to ensure performance.
• Select a dry place to locate the controller to prevent water could be splashed on.
• Pay attention during magnets assembly. It is recommended to locate the magnetic pad close to the outside wall of the fish tank to prevent breaking the fish tank and then shift it in correspondence with the pump location.
• Never disassemble the controller and the adaptor without professional guidance.
• Never repair a damaged cable without professional guidance. In case of main cable damage, change the entire pump or power supply unit.

Maintenance & FAQ

Why I cannot change for the Mode?
Check if the Night Mode is On and Off it again. If Wireless is “S”, the pump is controlled by the master pump, change the wireless mode to N (Standalone)to allow for local settings. Check the Timer if you change back to F6 Mode, after setting the timer, you need to switch F6 to run.
Make sure all the timer program T1-T6 is set, remember to check it does not overlap corrupt at the same time. Otherwise will not function.
How Can I reset the controller?
Hold the Reset button for 3 seconds, it will reset the controller programs to the factory status.
How many time periods can I program each day?
Up to 6 time periods per day.
Why I cannot succeed using F0 mode?
F0 Mode(Stop the pump), The function only works in Timer mode.
Why my program time cannot be run?
Check the Timer if you change back to F6 Mode, after setting the timer, you need to switch F6 to run.
My pump produces some noise. What can I do?
New pumps could have temporary sound issues. Normally the noise will be naturally reduced after one wee operation. You can also try to take out the impeller and reinstall the rubber bush.
How I can set for the Master and Slave Pump?
Set WIFI Button to “M” for A Pump, and set B Pump controller WIFI to “S”.
Which parts are consumables?
THE IMPELLER / THE RUBBER BUSH AND THE COVER ARE CONSUMABLE ITEMS, WE RECOMMEND CHECKING REGULARLY THEIR STATUS AND CHANGING THEM AFTER 1 YEAR TO PROVIDES THE BEST PERFORMANCES.

Package Content

Coral Box wavemaker pump

|

Wireless controller with connection cable

Power unit with power cable

|

Bi-adhesive

User manual

|

• This product is for indoor use Never submerge the controller, the power supply unit, or the connector sin the water to avoid unnecessary loss.
• Regularly clean the controller to ensure good performance.
• Rub the controller surface with a dry cloth if it has been accidentally wetted to prevent water drip into the controller.
• Sweep the waste in the pump housing and on the propeller by opening the pump Rotate the basket in an anti-clockwise direction to open the housing and lock it by rotating in a clockwise direction.
• Use a soft cloth to rub the blade and clean the dirt in the pump.

Ⅶ.WEEE

EU Waste Electrical and Electronic Equipment (WEEE) Directive In August of 2005, the European Union(EU) implemented the EU WEEE Directive 2002/96/EC and later the WEEE Recast Directive 2012/191EU requiring Producers of electronic and electrical equipment(EEE) to manage and finance the collection, reuse, recycling and to appropriately treat WEEE that the Producer places on the EU market after August 13, 2005. The goal of this directive is to minimize the volume of electrical and electronic waste disposal and to encourage re-use and recycling at the end of life. Coral Box has met its national obligations to the EU WEEE Directive by registering in those countries to which Coral Box is an importer.
Coral Box has also elected to join WEEE Compliance Schemes in some countries to help manage customer returns at end-of-life. If you have purchased Coral Box-branded electrical or electronic products in the EU and are intending to discard these products at the end of their useful life, please do not dispose of them with your other household or municipal waste. Coral Box has labeled its branded electronic products with the WEEE Symbol. (figure 1)to alert our customers that products bearing this label should not be disposed of in a landfill or with municipal or household waste in the EU.
Instead, please be aware that Coral Box is making a return and collection system available to you, free of transportation and recycling costs, for discarding these products. Can only be used by the Company if this document is publicly available. For a copy of Coral Box’s Selective Treatment of Waste Electrical and Equipment outlined under Articles 14 and 15 and Annex VII of the EU WEEE Directive 2012/19/EU, please click here WEEE Selective Treatment List and the list of hazardous materials used in our product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>