BlissLight Sky Lite Laser Projector User Guide
- June 7, 2024
- BlissLight
Table of Contents
BlissLight Sky Lite Laser Projector User Guide
NOTICE
CAUTION —Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This product is classified as a Class 2 laser product and complies with the
applicable parts of IEC/EN 60825-1 Ed. 2.0:2007 and Ed. 3.0:2014. The
manufacturer additionally certifies it complies with the US FDA Federal Laser
Product Performance Standard (FLPPS) provided in 21 CFR Subchapter J, 1040.10
and 1040.11 except for allowable deviations specified in FDA Guidance
documents.
Do not stare into the beams emitted from the product. Intentional long term
viewing of CLASS 2 levels of laser light can be hazardous. This product uses
diffractive optics to scatter the beam energy. This scattering effect causes
the energy concentration to drop below the exposure limits for momentary or
accidental viewing at a relatively short distance from the laser aperture. As
with all bright light-sources, when you operate this device in unsupervised
general public areas, it is recommended that up-close access to the light be
restricted or prevented and the beams be directed into locations were persons
are not
expected.
This laser display device incorporates a CLASS 3B laser system which, by
itself, may be hazardous. However, this laser display product incorporates a
protective housing and diffractive optics in its design so that there is no
exposure or human access to laser radiation during operation or maintenance
above the CLASS 2 limits. Each individual laser beamlet’s power is below the
Class 2 limit of 1 mW.
UNDER NO CIRCUMSTANCES shall attempts be made to open the protective
housing or operate the device if the aperture window is damaged.
All service to this laser display device requiring the protective housing to
be opened and/ or removed shall be performed by service personnel or their
authorized agents. Opening the protective housing voids the warranty.
NO LASERS SHOULD BE POINTED INTO THE Sky WITHIN 10 NAUTICAL MILES (18.5 km) OF AN AIRPORT. IF YOU ARE LOCATED WITHIN THIS SPECIFIC PERIMETER, WE RECOMMEND THE LASERS BE POINTED DOWN AT THE GROUND SO NO STRAY BEAMS ARE PROJECTED INTO THE AIR. CHECK WITH YOUR LOCAL AIRPORT OR PROVINCIAL GUIDELINES FOR FURTHER INFORMATION.
INTRODUCTION
Thank you for purchasing the BlissLights Sky® Lite Laser Galaxy Projector. This product is a unique indoor light fixture that uses patented laser and holographic technology to project thousands of moving pin-points of light against a transforming nebula cloud. Sleep under the stars, create a romantic starlit dinner, or take your home entertainment center to the next level. We hope you enjoy this incredibly unique lighting experience.
Each unit provides up to 30 x 30 ft of coverage. It has maximum electrical usage of less than 5 Watts and operates in temperatures between 14°F to 95°F (-10°C to 40°C).
BEFORE YOU BEGIN
Immediately upon receiving the fixture, carefully unpack and check the carton contents to ensure that all parts are present and in good condition. Notify the retailer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials. In the event that the fixture must be returned, it is important that the fixture be returned in the original factory box. Please see parts list below for box contents.
PARTS LIST:
- Laser Projector
- USB-C Power Cord
- Power adapter
Please note: Included adapter may vary from picture shown.
SETTING UP THE LASER PROJECTOR
Before operating your laser projector, please read the “Before you Begin” section and “Notice” section of this user’s guide.
- Remove protective film sticker from laser aperture.
- Insert the USB power cord into a powered USB port or use the included wall adapter to connect to an available electrical outlet. It is best practice for users to connect the power adapter to the wall before connecting the device to the power adapter.
- Place the Sky® Lite on a flat solid surface and aim toward desired ceiling/wall.
- Press the power button. The nebula and laser stars will gradually illuminate and begin moving by default.
- To adjust the illumination angle for walls, tilt the light forward onto the secondary support panel.
- To turn off the light, cycle through the power button modes until the unit turns off completely. Remove the power plug from electrical outlet.
- Use the following buttons to control lighting effects:
DEFAULT SETTINGS
Once the laser projector is plugged in, it will enter the default mode where all effects are on. Use the buttons to change the effect settings and brightness. This light has a built-in timer that is designed to automatically shut off after 6 hours of operation.
INSTALLATION TIPS
- Do not connect the light to a dimmer pack, as a dimmer accessory may damage the laser component.
- The darker the display area, the brighter your projection will appear.
PRODUCT SPECIFICATIONS
Designed in the USA
By BlissLights LLC
100 E San Marcos Blvd
San Marcos, CA 92069
Made in China
BLISSLIGHTS LIMITED WARRANTY
This product carries a limited warranty against defects in workmanship and
materials. BlissLights LLC agrees to replace the defective product free of
charge within the stated warranty period, when returned by the original
purchaser with proof of purchase. This product is not guaranteed against wear
or breakage due to misuse and/or abuse. For detailed warranty information for
your country,
please visit
www.blisslights.com/warranty
CAUTION
This is not a toy. Young children must be supervised while using this device
at all times.
This unit is not waterproof. Use and store indoors or in a dry place.
CLEANING INSTRUCTIONS
Surface clean only with a soft, dry cloth. Unplug unit before cleaning.
DISPOSAL
