Megateh Vues PoE Switch 4+1 User Manual
- June 7, 2024
- Megateh
Table of Contents
Megateh Vues PoE Switch 4+1
| Warning
Improper use of this product and accessories are dangerous to you and others
and can damage, destroy or cause a serious accident. We therefore ask you to
read the manual carefully and to read and strictly observe the danger, safety
and warning messages.
---|---
Introduction
hanks for choosing Vues! Read the manual carefully for correct and safe operation of the product. Always follow these instructions for safe usage. If you have any questions about the product or encounter problems, you can contact us by email: support@algebra2.nl
Vues PoE Switch
The Vues PoE Switch is a 100M Ethernet POE power supply switch. It provides 5
10/100M adaptive RJ45 ports.
At the same time, ports 1~4 has a PoE power supply function and can be used as
Ethernet power supply equipment. All power supply ports can Automatically
detect and identify the power receiving equipment that meets the IEEE
802.3af/at standard.
Getting started
The illustrations in this manual have been created with care. However, some
parts of the product may differ from the illustration shown in this manual. In
that case, Vues is not obliged to adjust the part or the manual.
This manual is intended for the end user of the product. Using the table of
contents on the next page you can find the necessary information in the
manual.
Specifications
| PORT | POE | 4*100Mbps POE Port |
|---|---|---|
| RJ45 Uplink | 1*l00Mbps Uplink | |
| Features | Store and forward | Support |
| Exchange content | 1.2G | |
| MAC | 2K | |
| Using environment | Working temperature : 0°C~40″C Storage temperature : |
-40°C~70°C
Working humidity : 10%~90% RH Storage humidity : 5%~90% RH
POE Standard| Standard IEEE802.3af / at The single port is30WMAX, the power of
switch is 52W
Support protection of over current, over voltage and short circuit
Support high-power PD soft start
Input power| AC 220V 50/60HZ
Output power| DC52V Power 52W
Supported standards and protocols| IEEE802.3 IEEE802.3i 10BASE-T
IEEE802.3u lO0BASE-TX IEEE802.3af IEEE802.3at
IEEE802.3x
Default system mode| Ordinary POE switch
250M transmissio111
Data transfer rate| Ethernet l0Mbps half duplex, 20Mbps full duplex
Fast Ethernet 100Mbps half duplex, 200Mbps full duplex
Network medium| 10Base-T: 2 to Cat3 or UTP/STP(Sl00m) 100Base-TX: 2 to cats
or UTP/STP(S100m)
10Base-TX: 2 to Cat6 or UTP/STP(S250m)
Physical specifications| 124mm'”115mm33mm (L W*H)
Instructions
Packing List
Open the packing box carefully, confirm the items should be as follows:
- 1 pcs x PoE switch
- 1 pcs x AC power cable (EU plug)
- 1 pcs x user manual
PS: Please contact a local dealer timely if you find the accessories missed or damaged.
The schematic of device connection
Precautions for installation
| Warming : It is A-level products, which might cause wireless
interference in the living. Environment. Some practical measures might be
taken to deal with the interference under the condition
---|---
| Note : Please obey the precautions below to avoid product damaged and
personal injury caused by improper using
Precautions for installation:
- Please keep the power off during the whole installation.
- Please provide the power which consistent with the power marked because the switch only works well under the correct power.
- Please confirm that it will not cause the overload on the circuit and the power before energizing the switch, to avoid affecting the normal working on the switch even unnecessary damage. Please do not open the shell of the switch when it is
- working, to avoid the danger of the electric shock; do not open it yourself even if it is not energized.
Precautions for installation environment
Temperature and humidity
- To guarantee the long-life stable working of the switch, please keep the stable temperature and humidity of the environments.
- It will cause the leakage of insulation materials, deformation even metal shedding to corrosion when under the too high or too low humidity.
- It will accelerate the aging process of insulation materials, seriously affect the service life of the device when the temperature is too high
The temperature and humidity for normal working and storage:
| Environments | Temperature | Relative humidity |
|---|---|---|
| Working environment | -15C–55C | 10%– 90%RH |
| Storage environment | – 40C– 70C | 5%–90%RH |
Indoor dust proof
It will cause electrostatic adsorption and poor contact of the metal connector
when the dust is attached to the surface of the switch. Some measures have
been taken on anti-static of the device itself, but fatal damage can happen on
the electronic component of the inside circuit board when the static is beyond
a certain intensity.
To avoid static on the normal working, please pay attention to the below:
Remove the dust regularly, keep the air clean indoor.
Confirm the well connection of the device, ensure the smooth transfer of the
static.
Electromagnetic interference
It will affect the capacitance, inductance, and other electronic components
inside the device by capacitive coupling, inductive coupling, impedance
coupling, etc.
To reduce the adverse effects caused by electronic magnetic interference,
please pay attention to the below.
The necessary measures of anti-power grid interference should be taken with
the power system.
The switch 2 be kept off the high frequency and high-power devices, etc.
The measures for electromagnetic shielding should be taken when necessary.
Demand for Lightning Protection
It will cause the fatal damage to the electronic device by the split-second powerful current when the lightning occurs. To achieve the better effect of lightning protection, please pay attention to the below:
- Confirm the rack with good grounding.
- Confirm the power outlet with good grounding.
- Reasonable wiring to avoid lightning internal induction.
- Recommend usage of signal lightning arrester when wiring outdoor
Connection of the hardware
| Please confirm that the device is equipped with the PoE if the switch is
passive; at the same time, please confirm the voltage of the access device is
matched with the switch’s, otherwise it will burn the access device.
---|---
Connect to the RJ45 Port
-
Connect one end of the cable to the switch and the other end to the corresponding device, as shown as illustration 2
illustration 2. Device connection -
Please check the condition of the corresponding indicator when electrified. It means the connection works well when the indicator is ON; blocked when it is OFF, please check the wiring and confirm the corresponding device start up
Connect to the Power Cable
- Confirm the consistency of the chosen power and the power marked on the switch.
- Connect the switch with the outlet by the original power cable, as shown as illustration5-2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>