OWNER’S MANUAL
and TECHNICAL DOCUMENTATION
Model 280-3700
Mart Cart™ is a quality product line of Assembled Products™ Corporation
115 E. Linden
Rogers, Arkansas 72756 USA
479-636-5776
479-636-3245 fax
1-800-548-3373 www.martcart.com

mart cart 280-3700 Electric Shopping Cart

— IMPORTANT INFORMATION —
Please read before operating.

CONGRATULATIONS!
You have just purchased the best electric shopping cart on the market todayThis Mart Cart incorporates the very latest in technological advances. To assure you of the best and safest performance as well as longest life, please read the enclosed information.  After reading this manual, should you have a service problem or need help, please call our Customer Service Department with the serial number of your cart, at our toll free number: 1-800-548-3373 or 479-636-5776.
DAMAGE: Check the shipping carton for any visible damage. Report the damage to the freight carrier immediately. File a claim with the carrier if actual damage to your cart has occurred. Check the contents of the carton.
The contents should agree with the information listed on the packing list.
Report any discrepancy to the carrier and the factory immediately.
TO ORDER PARTS : Call 1-800-548-3373 or 479-636-5776. Be sure to give the serial number to the Service Department personnel. The Mart Cart serial number is located on the seat support tube under the seat as shown in parts list portion of this manual.
TERMS: All parts will be shipped with approved credit card, check in advance or C.O.D. Commercial accounts are allowed 15 day terms from date on invoice with approved credit.
FREIGHT: All freight will be paid by the customer. Special consideration will be given to items under warranty coverage.
ATTENTION: It is the responsibility of the owner of this cart to maintain the cart in a safe and reliable operating condition at all times.
NOTE: Specifications found in this manual subject to change without notice

IMPORTANT SAFETY INSTRUCTIONS

Please read before operating.
WARNINGS

• Never attempt to charge the battery in this cart without using an electrical outlet that is protected by a GFCI.

• Replace charging cord if plug is damaged or if the cord is worn or frayed.
  Never use the charging cord without proper grounding. Do not use if plug does not have three prongs.

• Never allow the cart to be used out-of-doors or on any surface that is not level.

• Always disconnect power before servicing.

• See “Daily Maintenance Checklist,” and follow instructions.

• Cart can roll. Enter and exit cart with care.

• Replace parts using only factory-specified, original equipment from the manufacturer for your specific model. Failure to do so may void warranty, affect operation of the cart, and result in injury.

OPERATING PROCEDURES

• New carts will need charging! Charge batteries for 24 hours prior to first use.
• THIS CART IS FOR USE INDOORS ON A FLAT, LEVEL SURFACE ONLY
• DO NOT STAND ON CAR0T. (See “Operating & Warning Instructions” on cart).
• After battery is charged, disconnect power supply cord BEFORE operating cart.
• DO NOT exceed the load limitations as shown on the cart.
• Return power cord to circular cavity when not charging
• DO NOT allow children to operate or play on cart. Keep cart secured with key (if applicable), at service counter.

DAILY MAINTENANCE CHECK LIST

For optimum cart availability and performance, the following items should be checked daily:

• ELECTRIC CORD—Replace cord if cord is worn or frayed, 3-pronged plug is broken or reel (optional) will not retract. Be sure power outlet provides protection through an operating “Ground Fault Circuit Interrupter” (GFCI).
• SEAT AND MOUNTING—Tighten if necessary. If cracks or rust occur, or if seat rocks loosely, replace at once.
• SEAT SWITCH—Test and replace if not working properly. Cart must stop when weight is removed from seat.
• THROTTLE—Test for smooth “start, acceleration, deceleration, and stop.” Repair if necessary. Charge or replace battery if needed.
• ANTI-TIP CASTERS—Replace if broken. Maintain height adjustment of 1/8” to 1/2” above floor level.
• GENERAL—Repair or replace any component that may cause a potential safety hazard.
• APPEARANCE—Wipe off and clean as needed for customer satisfaction and for store’s public image.

BATTERY CHARGING INSTRUCTIONS

Please read before charging.
Your cart is equipped with the Intelli-Charge™ system. While operating the cart, the LED will be solid green until the battery falls below 12.4 volts and then turns solid amber. When the battery charge falls below 10.5 volts, the LED will begin flashing red. The  person riding the cart should have ample time to return the cart for charging. When the rider exits the cart, the horn will start beeping in unison with the red flashing LED. This will alert those responsible for maintaining the cart to plug in the charger. When  plugged into a 120v AC wall socket, the LED will flash amber and the horn will silence.
When charging is complete the LED will start flashing green. The charger may be left plugged in even longer as it will NOT harm the battery.

switch is engaged – battery is fully charged
Amber (solid)| ff/On rocker switch is set to “On” position – seat
switch is engaged – battery is below 12.4 volts
Red – Flashing|  Battery needs to be charged – below 10.5 volts
LED Color Status| Description while charging
---|---
Amber – Flashing| Charger is plugged in and battery is being charged
Green – Flashing| Charger is plugged in and battery is charged

• Install a Ground Fault Circuit Interrupter (GFCI) in the electrical circuit wherever the cart is to be charged. This is to protect against any possible shock hazard.
• AC voltage required is 100-240 VAC (50/60 Hz). The current draw is 3.5 amps maximum.
• Charge battery every night, all night, and at every opportunity. When the battery is fully charged, the charger will maintain a “float voltage” which will not damage the battery.
• Do not allow the battery to fully discharge by skipping the nightly charging cycle. A fully discharged battery will take 7 hours to fully charge, so it is best not to let the battery become completely discharged.
• Do not store the cart with a discharged battery. This can cause premature battery failure. Fully charge the battery at least every 30 days if in a low usage location.
• No maintenance of battery is required. The AGM battery is maintenance free and water cannot be added.

NOTE: Under normal conditions, the battery will last more than 2 years or longer if the above recommendations are followed. Replace with original

Mart Cart battery only. Mart Cart is not responsible for any adverse effects caused by replacement with any other type of battery.
IMPORTANT: Your cart has been equipped with an AGM (Suspended Electrolyte) Battery during the manufacturing process as original equipmentThe manufacturer recommends that you replace the original battery only with the same type and rating to prevent damage to your cart’s internal components, charging system, or personal injury to you and your customer.

— BATTERY REPLACEMENT INSTRUCTIONS —
Please read before replacing battery.

Be Responsible! Recycle old battery or dispose of according to local or national codes. See next column, under DISPOSAL.
To Replace Battery: (Read precautions on batteries, under Charging Instructions and Safety Precautions, to avoid any sparks)

1. Turn off key switch (if equipped, or flip On/Off switch to “Off” position).
   Disconnect charger cord from wall outlet, if plugged in.

2. Reach under right rear of back cover and pull latch, then tilt chair forward3. Remove rear cover.
   CAUTION: Do not cross battery posts with metal object!

3. Remove old battery and place new battery.

4. Before reinstalling cover, check wheel condition, and general condition of the chair.

5. Reinstall rear cover and tilt chair back.

6. Test cart for proper operation. Charge battery if necessary.

ADDITIONAL INFORMATION

SEAT LOCK
For XTi 12 with sliding seat. The seat lock and the chair should be inspected daily for proper function. The release/locking arm should move freely and spring back into locking position. If return spring is broken, DO NOT USE cart until spring is replaced.
SEAT SWITCH
The seat switch is located under seat. Pressure (weight) on the seat closes the control circuit, and allows the cart to operate.
VARIABLE SPEED CONTROL
The cart’s speed is regulated by a potentiometer. This provides extremely smooth acceleration from 0 to 2.2 MPH, and is located in the control box on the steering column.
CIRCUIT BREAKER
The circuit breaker is designed to protect your electrical system from transient overloads or electrical shorts. Either could cause serious damage without a circuit breaker to open the circuit. The circuit breaker is a manual reset type. It requires manual  resetting once it has been tripped.

CHARGING
HOW IT WORKS: When the power supply cord is plugged into the store’s electrical outlet the battery charger is energized. The charger sends approximately 14.5 volts to the battery for charging. A third wire (yellow) from the charger output inhibits the PWM  until the power to the charger is disconnected. The motor circuit is interrupted until charging is complete.
NOTE: The cart will not move under power when the battery is being charged. If the cart moves while plugged in, check the power to your outlet before calling for service.
CONTROL BOX
The master control box is located on top of the steering column. It contains the RUN/STOP/HORN switch, and key switch (optional keyless system available). The cover can be removed by removing the four bottom screws.
Our models are equipped with the Intelli-Charge™ system, a bicolor LED can be found in the RUN/STOP/HORN switch.

DISPOSAL

Please read before disposing your old battery.
The Mart Cart model number 280-3700 is certified 100% by Recycle America, LLC., a subsidiary of Waste Management and those models are PVC free. Spent batteries must be treated as hazardous waste and disposed of in accordance with local, state and  federal guidelines.
The BATTERY ACT of 1996 applies to battery disposal and recycling.
The life expectancy of the Mart Cart is 7-10 years. The life expectancy of the battery can be 2 years or longer with recommended charging procedures. The disposal of the Mart Cart can be administered by any local metal recycling center. The recycling of the  battery can be administered by any local battery recycling center.

PARTS LISTS AND SCHEMATICS

Control Box Parts List

*NOTE: Parts are ordered in Contol Box Kits below.

CONTROL BOX KITS :

DECALS FOUND ON MART CART® ELECTRIC SHOPPING CART

Please call 1-800-548-3373 if your decals are missing or are needing replacement.
Standard decals and signs are English and Spanish (see part numbers below). Call for other languages.

DAILY MAINTENANCE CHECK LIST
For optimum Cart availability and performance, the following Items should be checked daily:

1. ELECTRIC CORD and orREEL . Replace cord and’or reel if cord is worn or frayed, 3 pronged plug is broken or reel will not retract Be sure Power-Outlet provides protection through an operating Ground Fault Circuit Interrupter (GECI).
2. SEAT & MOUNTING – Tighten it necessary. If cracks or rust occur, or If seal rocks loosely, replace at once. Lubricate swivel or tracks with +timeline as required. Make sure Seat Lock Is In good working condilion.
3. SEAT SWITCH – If cart is equipped with a seat switch. test and replace it not working property. Cart must stop when weight is removed from seat.
4. THROTTLE – Test for smooth “starr, acceleration, deceleration and “stop”. Repair if necessary. Charge or rDSato.
5. ANTI-TIP CASTERS – Replace if broken. Maintain height adjustment of it to 1!? above floor level
6. GENERAL – Repair or replace any component that would cause a potential ‘Safety Hazard’.
7. APPEARANCE – Wipe oft and clean as needed for customer salis’action and for store’s ‘Public Image’.

FOR PARTS OR SERVICE CALL
800-548-3373 or 479-636-5776 200 112t

280-1095

WARNING

PLEASE READ TO AVOID PERSONAL INJURY. USE AT YOUR OWN RISK! ICrf INTENDED FOR USE INDOORS ON LEVEL SURFACE ONLY!

1. Read operating instructions or ask for assistance before using.
2. Use extra caution getting “ON” or “OFF” cart.
3. Cart is on wheels and may roll.
4. You must be seated to operate cart.
5. Keep feet and legs inboard while operating.
6. Do not stand on cart.
7. Do not lean “ON” or “OVER” the side of the cart.
8. NO CHILDREN IN BASKET.

OPERATING INSTRUCTIONS  PLEASE READ BEFORE OPERATING

1. Turn key on and/or press the Tun’ switch.
2. Thumb levers rotate to power the cart. Press top lever forward to go forward. Press bottom lever down to go in reverse.
3. To stop, release the thumb levers and/or press the ‘stop’ switch.
4. If needed, ask cashier for assistance to get your items to your vehicle. Under no circumstances are carts to be taken outside the store.

DO NOT REMOVE FROM STORE

WWW.MARTCART.COM

Warning
FIRE HAZARD, USE ONLY 280-1214 MART CART BATTERY. DO NOT MODIFY THE WIRING HARNESS OR THE BATTERY COVER

IN-STORE USE ONLY
FOR OUR VALUED CUSTOMERS… BECAUSE WE CARE-
IN-STORE USE ONLY
NO CHILDREN IN BASKET!

Charge Batteries For 24 Hours Prior to First Use.

PULL LATCH UNDERNEATH TO REMOVE COVER

IF CORD IS LOST OR DAMAGED PLEASE USE REPLACEMENT CORD UNDER COVER

000-1183

CHARGE EVERY NIGHT ALL NIGHT AND AT EVERY OPPORTUNITY

Quick Change Battery Cove;
NO TOOLS NEEDED LIFT HERE TO REMOVE DO NOT STAND ON BUMPER
280-2103

NOTE: #31 (wire guide) and #26 (wire harness) can be ordered as an assembly part 280-1656

35 (cord cover) & #37 (cord cover lid) can be ordered as an assembly part

280-0004

Electrical Schematic

When this cart is equipped with controller 280-1569, use this schematic.

When this cart is equipped with controller 280-1935, use this schematic.

MATERIAL SAFTY DATA SHEET

Product Name: Sealed Maintenance Free Lead-Acid Batteries|
---|---
DATE:|  1/5/2005| ISSUED BY|  TELEPHONE NO.| 479-636-3245
---|---|---|---|---

HAZARDOUS COMPONENTS

PHYSICAL DATA

COMPONENTS| DENSITY| MELTING POINTS| SOLL U
(1420BILITY )| ODOR| APPEARANCE
---|---|---|---|---|---
Lead| 11.| 327.4° C (Boiling)| None| None| Silver-Gray Metal
Lead Sulfate| 6.| 1070° C (Boiling)| 40 mg/1(15° C)| None| White Powder
Lead Dioxide| 9.| 290° C (Boiling)| None| None| Brown Powder
Sulfuric Acid| about 1.3| about 114° C (Boiling) ,| 100%| Acidic| Clear Colorless Liquid
Fiberglass Separator| N/A| N/A| Slight| Toxic| White Fibrous Glass
ABS Plastic| N/A| N/A| None| No Odor| Solid

FLAMMABILITY DATA

(float voltage > 2.40 VPC).
Fiberglass Separator| N/A| N/A| Toxic vapors may be released. In case of fire, wear self-contained breathing  apparatus.
ABS Plastic| None| N/A| Temp. over 300° C (572° F) may release combustible gases. In case of fire:  wear positive pressure self-contained breathing apparatus.

FRIST AID

SULFURIC ACID PRECAUTIONS

Skin Contact:| Flush with water, see physician if contact area is large or if blisters form.
Eye Contact:| Call physician immediately and flush with water until physician arrives.
Ingestion:| Call physician. If patient is conscious, flush mouth with water, have patient drink milk or sodium
bicarbonate solution. National Poison Center: 1-800-222-1222

REACTIVITY DATA

area. Avoid mixing acid with other chemicals

SPILL OR LEAK PROCEDURES

Steps to take in case of leak or spill:| If sulfuric acid is spilled from a battery, neutrilize acid with bicarbonate (baking soda), sodium carbon (soda ash), or  calcium oxide (lime). Flush area with water and discard to the sewage system. Do not allow unneutralized acid into  sewage system.
---|---
Waste disposal method:| Neutrilized acid may be flushed down the sewer. Spent batteries must be treated as hazardous waste and disposed of  according to local, state, and federal guidelines. A copy of this MSDS must be supplied to any scrap dealer or secondary  lead smelter with battery.

PROTECTION

is cracked or
otherwise damaged. A respirator should be worn during reclaim
operations if the TLV is exceeded.
RESPIRATORY| Respirator (for lead)
EYES| Safety goggles, Face Shield

ELECTRICAL SAFETY

Due to the battery’s low internal resistance and high power density, high levels of short circuit current can be developed across the battery terminals. Do not rest tools or cables on the battery. Use insulated tools only. Follow all installation instructions and diagrams when installing or maintaining battery systems.

HEATH  HAZARD DATA

LEAD: The toxic effects of lead are accumulative and slow to appear. It affects the kidneys, reproductive, and central nervous systems. The symptoms of lead overexposure are  anemia, vomiting, headache, stomach pain (lead colic), diminess, loss of appetite, and muscle and joint pain. Exposure to lead from a battery most often occurs during lead  reclaim operations through the breathing or ingestion of lead dust or fumes.

SULFURIC ACID: Sulfuric acid is a strong corrosive. Contact with acid can casue severe burns on the skin and in eyes. Ingestion of sulfuric acid will cause GI tract burns. Acid  can be released if the battery case is damaged or if vents are tampered with.
FIBERGLASS SEPARATOR: Fibrour glass is an irritant of the upper repiratory tract, skin and eyes. For exposure up to I OF/CC use MSA Comfoll with type H filter. Above  10F/CC up to 50F/CC use Ultra-Twin with type H filter. This product is not considered carcinogenic by NTP or OSHA.
ALL DATA MUST BE PASSED TO ANY SCRAP DEALER OR SMELTER WHEN BATTERY IS RESOLD.

Specifications are subject to change without notice .

115 E. Linden • Rogers, Arkansas 72756 USA
479-636-5776 • Fax: 479-636-3245
www.martcart.com
800-548-3373
MC1-MODEL-3700-OM-191101-EN Printed in the USA.

Documents / Resources

| mart cart 280-3700 Electric Shopping Cart [pdf] Instruction Manual
280-3700 Electric Shopping Cart, 280-3700, Electric Shopping Cart, Shopping Cart
---|---

References

• Mart Cart™ | Quality, Performance, Value
• Mart Cart™ | Quality, Performance, Value

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>