spl TDx-500 Series Transient Designer Module Owner’s Manual
- June 9, 2024
- spl
Table of Contents
spl TDx-500 Series Transient Designer Module Owner's Manual
Introduction
Developer
Wolfgang Neumann
Version 2.0 – 12/2022
This manual contains a description of the product. In no way it represents a
guarantee of particular characteristics or results of use. The information in
this document has been carefully compiled and verified and, unless otherwise
stated or agreed upon, correctly describes the product.
Specifications are subject to change without notice.
Specifications
Scope of Delivery
TDx module, 500 Series
Manual
Measurement & Weight
Single-slot module, 500 Series
Weight: 1.43 lbs (0.65 kg)
Please keep the original packaging. In a service case the original packaging
ensures a safe transport.
Installation
Installation into a 500 Series rack:
- Please read the manual that comes with the 500 Series rack. You should receive all necessary information for the installation process.
- For the installation or exchange of TDx, your 500 Series rack should be switched off and the power cable should not be connected.
- Insert the TDx module into a free slot of your rack. Make sure the connector of the TDx is precisely aligned with the rack connector.
- Press the TDx module carefully into the rack connector and tighten the screws.
- Connect the TDx module with your audio environment using the connections from your 500 Series rack.
- Insert the power cable to the 500 Series rack and switch it on.
Control Elements
Signal LED
The signal LED Sig indicate whether an audio signal is present at the
input of the respective channel with a level higher than -20 dBu.
These LEDs serve as an assistant to quickly detect whether a signal arrives at
the TDx within a complex studio cabling
On/Bypass
The On/Bypass switch activates or deactivates (Bypass) the module.
ATTACK
ATTACK can be used to increase or attenuate the attack phase of a signal by up to 15 dB. Positive attack increases the amplitude of the attack phase. Negative attack attenuates the amplitude of the attack phase.
SUSTAIN
SUSTAIN can be used to increase or attenuate the sustain phase of a signal by up to 24 dB. Positive sustain values extend the sustain. Negative Sustain values shorten the sustain.
MIX
The MIX control allows continuously blending between processed (WET) and unprocessed (DRY) signals.
OUTPUT
With the OUTPUT control the output gain can be attenuated in order to optimally drive following devices.
Security Advices
Before starting up the device:
- Read thoroughly and follow the security advices.
- Read thoroughly and follow the manual.
- Observe all warning instructions on the device ad on your 500 Series rack.
- Please keep the user manual as well as the security advices in a safe place for future reference.
- Module installation and replacement should only be carried out by qualified technicians.
- Please refer to and heed the safety and assembly instructions of your 500 Series rack.
Warning
Always follow the security advices listed below to avoid serious injuries or even deadly accidents due to electric shocks, short circuit, fire or other dangers. The following are examples of such risks and do not represent an exhaustive list:
Do not open
This device contains no user-serviceable parts. Do not open the device or attempt to disassemble the internal parts or modify them in any way. If it should appear to be malfunctioning, turn off the power of your 500 series rack immediately, unplug the power cord from the mains socket outlet and have it inspected by a qualified professional.
Water warning
Do not expose the device to rain, or use it near water or in damp or wet conditions, or place anything on it (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the device, turn off the power of your 500 Series rack immediately and unplug the power cord from the mains socket outlet. Then have the device inspected by a qualified professional.
Fire warning
Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire.
Lightning
Before thunderstorms or other severe weather, disconnect your 500 Series rack from the mains socket outlet; do not do this during a storm in order to avoid life threatening lightning strikes. Similarly, disconnect all the power connections of other devices, antenna and phone/network cables which may be interconnected so that no damage results from such secondary connections.
If you notice any abnormality
When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug of your 500 Series rack from the mains socket outlet. Then have the device inspected by a qualified professional.
- The device emits unusual smells or smoke.
- An object has fallen into the unit.
- There is a sudden loss of sound during the use of the the device.
Caution
Always follow the basic precautions listed below to avoid the possibility of
physical injury to you or others, or damage to the device or other property.
These precautions include, but are not limited to, the following:
Location
Do not place the device in a location where it may come into contact with
corrosive gases or salty air.
This may result in malfunction.
Before moving the device, remove all connected cables.
Connections
Before connecting the device to other devices, power down all devices. Before
power on or off the devices, set all volume levels to minimum.
Only use appropriate cables to connect the device with other devices. Make
sure that the cables you use are intact and comply with the electrical
specifications of the connection. Other connections can lead to health risks
and damage the equipment.
Handling
Operate the controls and switches only as described in the manual. Incorrect
adjustments outside safe parameters can lead to damage.
Never use excessive force on the switches or controls.
Do not insert your fingers or hands in any gaps or openings of the device.
Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings of the device. If this happens, power down immediately and unplug the power cord from the mains socket outlet. Then have the device inspected by a qualified professional.
Do not expose the device to excessive dust or vibrations or extreme cold or heat (such as direct sunlight, near a heater or in a car during the day) to prevent the possibility of causing damage to the housing, the internal components or unstable operation.
If the ambient temperature of the device suddenly changes, condensation can occur (if for example the device is relocated or is affected by a heater or air conditioning).
Using the device while condensation is present may result in malfunction. Do not power on the device for a few hours until the condensation is gone. Only then it is safe to power on.
Cleaning
Disconnect the device from your mains socket outlet before cleaning.
Do not use any solvents, as these can damage the chassis finish. Use a dry
cloth, if necessary, with an acid-free cleaning oil.
Disclaimer
The company names and product names in this manual are the trademarks or
registered trademarks of their respective companies.
SPL and the SPL Logo are registered trademarks of
SPL electronics GmbH.
SPL cannot be held responsible for damage caused by improper use or
modification of the device or data that is lost or destroyed.
Notes on Environmental Protection
At the end of its operating life, this product must not be disposed with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment.
The wheelie bin symbol on the product, user manual and packaging indicates
that.
For proper treatment, recovery and recycling of old products, please take them
to applicable collection points in accordance with your national legislation
and the Directives 2012/19/EU.
The materials can be reused in accordance with their markings. Through reuse,
recycling of raw materials, or other forms of recycling of old products, you
are making an important contribution to the protection of our environment.
Your local administrative office can advise you of the responsible waste
disposal point.
This directive only applies to countries inside the EU. If you wish to discard
devices outside the EU, please contact your local authorities or dealer and
ask for the correct method of disposal.
WEEE-Reg-No.: 973 349 88
Support und Contact
help.spl.audio
SPL electronics GmbH
Sohlweg 80
41372 Niederkrüchten
GERMANY
SPL can of course also be found on Facebook, Instagram, Twitter and Youtube and we are happy to welcome new friends, followers and viewers.
Website & Blog: www.spl.audio
Videos: youtube.spl.audio
Instagram: instagram.spl.audio
Twitter: twitter.spl.audio
Facebook: facebook.spl.audio
© 2022 SPL electronics GmbH
This manual/document is protected by copyright. All rights, technical modifications\ and printing errors reserved.
Copying, reproduction, translation or conversion into any electronic medium or machine-readable form in whole or in part is only permitted with the express written consent of SPL electronics GmbH.
Declaration of CE Conformity
The construction of this unit is in compliance with the standards and regulations of the European Community.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>