Jaycar AP4006 Portable LED Projector with built-in Speaker User Manual
- June 7, 2024
- Jaycar
Table of Contents
AP4006
PORTABLE LED PROJECTOR WITH BUILT-IN SPEAKERS
User Manual
ADDITIONAL WARNINGS AND PRECAUTIONS
- Do not look directly into the projector light.
- Don’t touch the project lens
- The mains adapter is used as a disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.
- Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.
- Changes or modified to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the
- Use of this unit near fluorescent lighting may cause interference regarding the use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause.
- Shock hazard – Do Not Open.
- Caution and marking information is located at the rear or bottom of the apparatus.
- To reduce the risk of fire or electric shock, do not expose this apparatus to rain, moisture, dripping, or splashing.
- Objects filled with liquids, such as vases, shall not be placed on the apparatus.
- Last but not least, if you can not get sound from the projector when you play Dolby sound videos, (Amazon fire stick, Netflix, Blue-ray movies and so on) Please turn off the Dolby sound on your device or apps.
PRODUCT OVERVIEW
1. POWER Button
2. RETURN Button
3. NAVIGATION
4. MENU Button
5. SOURCE” ” Button
6. Keystone Correction
7. Focusing Ring
8. LENS
9. Headphone Jack
10. AV| 11. Micro SD Card
12. HDMI Port 1
13. HDMI Port 2
14.USB Port
15. DC
16. VGA Port
17. POWER on Indicator
18. IR Window ( Rear Side)
19. IR Window ( Front Side)
20.Adjusting Knob
---|---
CONTROL
Install Power Adapter
Follow the below picture to connect the power adapter Connect the small end of the adapter first. Plug the adapter body into a power outlet.
CONTROLS OF REMOTE
Install / Remove Battery Of Remote
Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (2 X AAA batteries not included), referring to the polarity markings. Finally, replace the cover.
NOTES:
- Batteries shall not be exposed to excessive heat such as sunshine, fire
- Be sure that the batteries are installed polarity correctly.
- Only same or equivalent type batteries as recommend are to be used.
- Do not dispose of batteries in fire, the battery may explode or leak. Do not try to recharge a battery
- Do not mix old and new batteries.
- Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-me, etc) batteries
SPECIFICATIONS
Light Source Type | LED |
---|---|
Display Native Resolution | 800 x 480 |
HDMI Input Supported Video Resolution. | 1080p , 1080i , 720p, 576i , 480p, and |
480i
Power Consumption| 42W
Power Input
Connect Included Adapter| DC 12.0V, 3.5A
Included Adapter Connect DC input of unit| Input AC100-240V,50/60Hz Output
DC12.0A , 3.5A
Display Color| 7000-8000K
Signal Port| Video / VGA / HDMI
USB Port| Support USB device up to 1TB
Support format mpegl, Mpeg2 ,mpeg4, mp3 , Jpeg
SD Card| Support SD card up to 32GB
Support format mpegl, Mpeg2 ,mpeg4, mp3 , Jpeg
Weight| 0.9 KG
Dimension| 203 x 150 x 82 mm
REMOVE & CLOSE THE LENS COVER
Placing Your Projector
Your projector can be installed in four different configurations ( see picture below):
Front Table:
Select this location with the projector placed near the floor in front of the
screen. This is the most common way to position the projector for quick setup
and portability.
Front Ceiling:
Select this location with the projector suspended upside-down from the ceiling
in front of the screen.
NOTE: A projector mount is required to install the projector in a
ceiling.
Rear Table:
Select this location with the projector placed near the floor behind the
screen.
NOTE: That a special rear projection screen is required.
Rear
Ceiling:
Select this location with the projector suspended upside-down from the ceiling
behind the screen.
NOTE: A projector mount is required to install the projector in a
ceiling. A special rear projection screen is required.
TO REDUCE IMAGE DISTORTION
It is recommended to move the projector as close to the center of the screen.
PLACING YOUR PROJECTOR ON THE CEILING
When installing the projector in the ceiling, please purchase a projector
mount recommended by an installation professional and follow the instructions
that come with the mount. Before installing the projector in the ceiling,
please check to make sure the ceiling structure can support the weight of the
projector and the mount. If in doubt, please ask the advice from an
installation professorial.
NOTE: Projector mount and screw(s) not included
ADJUST THE VERTICAL LOCATION
Follow the below picture to adjust the vertical location.
TO REDUCE IMAGE DISTORTION
It is recommended to move the projector as close to the center of the screen.
Adjust the focus by turning the knob while observing the image pixels near the
center of the screen. Optimal focus is obtained when the pixels are clearly
visible. Depending on the projected screen size, the focus near the screen
edges may be less sharp than the screen center.
keystone image is created when the projector beam is projected to the screen
in an angle. Keystone correction will restore the distorted image to a
rectangular or square shape.
Connect HDMI Show The Image On Projector Screen
Follow the below picture to connect the HDMI cable and device.
- Turn off the unit before connecting the HDMI cable.
- After connect, press the button to turn on the unit and the power indicator will light GREEN
- Press the ” ” / SOURCE button to HDMI mode and the video of the HDMI device will show on the projector screen. There is 2 HDMI input, the HDMI1 interface corresponds to HDMI 1 in SOURCE mode, and the HDMI2 interface corresponds to HDMI 2 in SOURCE mode.
- Press the buttons twice to turn off unit power.
CONNECTING
HDMI HD Signal Input: This Interface Can Be Input With HD Player HDMI Output At The Connection
In rare cases, if the projector’s speaker has no sound when playing a DVD
movie in a player connecting to the HDMI input, please check the player’s
digital audio settings and make sure it is set to °Auto” mode or *PCM-mode.
Connect AV Show The Image On Projector Screen
Follow the below picture to connect the AV cable and device.
- Turn off the unit before connecting the AV cable.
- Use AV cable to connect follow below figure
- After connect, press the buttons to turn on the unit, and the power indicator will light GREEN
- Press the” “/ SOURCE button to AV mode and the video of the AV device will show on the projector screen
- Press the buttons twice to turn off unit power.
Connect VGA Show The Image On Projector Screen
Follow the below picture to connect the VGA cable and device.
- Turn off the unit before connecting the VGA cable.
- Press the button twice to turn off the power of your projector before connecting.
- After connect, press the button to turn on the unit, and the power indicator will light GREEN
- Press the “` ” / SOURCE button to VGA mode and the video of the VGA device will show on the projector screen.
- Press the buttons twice to turn off unit power.
Please refer to the following table to adjust the output signal from the computer
Type | Resolution | Frequency | Field Frequency |
---|---|---|---|
PC | VGA | 640×480 | 31.5 |
34.7 | 70 | ||
37.9 | 72 | ||
37.5 | 75 | ||
SVGA | 800×600 | 31.4 | 50 |
35.1 | 56 | ||
37.9 | 60 | ||
46.6 | 70 | ||
48.1 | 72 | ||
46.9 | 75 | ||
XGA | 1024×768 | 40.3 | 50 |
48.4 | 60 | ||
56.5 | 70 |
Connect Audio Output (Aux Out / Line Out / Earphones)
Follow the below picture to connect the audio cable and device.
- Press the button twice to turn off the power of your projector before connecting.
- Use an audio cable to connect follow the below figure.
- After connect and turn on both units. Your projector sound from an external device now.
- After using, turn off both unit
Station Amplifire
Install USB Device And Micro SD Card
Follow the below picture to install a USB and MicroSD Card. Turn off the unit
before installing a USB / microSD Card.
Using microSD Card And USB Playback (Media Player)
Install USB / Micro SD device:
- Turn off the unit before installing a USB / microSD Card.
- Install the USB device into the USB port.
- After connect, press the buttons to turn on the unit and the power indicator light
- Press the “ ” / SOURCE button to enter and use buttons to search the MEDIAPLAYER mode.
- After selection, use “ ” buttons to search the MUSIC/ PHOTO / MOVIE icon and press the button to enter. If necessary, use the button to select microSD card or USB and press the button to enter.
- Use buttons to search the correct file and press the buttons to preview the playback file and press the buttons of the unit or button of remote to start playback.
- Press button to fast search forward and rewind.
- Press button to search the next or previous file.
- During playback, press the buttons to pause and press again to resume.
NOTE: Remove USB / microSD device, press the ** button twice to turn the power FIRST.**
TROUBLESHOOTING
Before requesting a maintenance service, please kindly check by yourself with the following chart.
No Image is Projected or a “No Signal” message is displayed| 1. Is the power
light on? If it is not on, check the projector is plugged into the mains, that
the socket is switched on, and then press the power button on the projector.
2. Check the lens cover has been removed.
3. Check the cables are securely attached and installed as per the User
Manual.
4. The image source may not be set correctly. Press the Source button on the
Control Panel or the Remote, to select the correct setting. 5. Check in the
Menu section under Video input signal to make sure that has been set
correctly.
---|---
The Lamp (Bulb) switches off after a period of time| 1. Leave the projector
to cool for a few moments.
2. Once cooled, check if anything is blocking the ventilation vents.
3. Tum on the projector.
If the issue persists please contact your support provider for further
assistance.
The Image is wider at the top/bottom of the screen| This is called keystone
and is due to the projection angle not being perpendicular to the screen. To
correct use the projectors inbuilt keystone function to adjust the image.
Spots on the screen| Using a vacuum cleaner to clean the lens. If cleaning
doesn’t resolve things, please contact your support provider for further
assistance.
The image brightness has faded| This could possibly be caused by the ambient
light in the room. If not, then chances are that you need to replace the lamp
(bulb).
Distributor: Electus Distribution Pty Ltd
Address: 320 VICTORIA RD, RYDALMERE NSW 2116 Tel: +61 2 8832 3200 Fax: +61 2 8832 3232
Web: www.electusdistribution.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>