AMCREST 4-8-Port PoE Switch User Manual
- June 7, 2024
- Amcrest
Table of Contents
AMCREST 4-8-Port PoE Switch
Important Safeguards & Warnings
Attention:
Please read the following safeguards and warnings carefully before using the
product in order to avoid damages and losses.
Note:
Do not expose the device to Soot, high humidity or dust. Doing so may cause
fire or electric shock. Do not install the device in direct sunlight as it may
cause overheating and failure. Installation of the unit should be via the
compatible rack mount or securely on a flat surface. Do not place the device
on carpet or other insulating surfaces. Ex. Rugs, towels, rags, clothing, etc.
Do not block or impede airflow to or around the unit. Doing so may cause
overheating, failure or fire. Do not place stack or place objects on the unit.
This unit contains no user serviceable parts. Servicing should only be
performed by approved technicians.
Warning:
Do not use a power supply other than the provided manufacturer power supply.
Failure to do so may cause unit failure and/or damage. Special Announcement:
This manual is for reference only. All the designs and software here are
subject to change without prior written notice. All trademarks and registered
trademarks are the properties of Amcrest Technologies LLC.
Applicable Models:
The manual can be applied to the following models:
MODEL NUMBERS PENDING: AMPS5E4P-AT-65, AMPS9E8P-AT-96
Product Overview
Features
Common Features:
Two-layer commercial PoE switch.
Conform to IEEE802.3, IEEE802.3i, IEEE802.3u and IEEE802.3X standards.
MAC auto study and aging, MAC address list capacity is 2K. All ports self-
adapt MDI/MDIX mode.
All the10/100M self-adaptive RJ45 PoE ports support IEEE802.3af and
IEEE802.3at standards.
Commercial wide temperature design.
Supports DC 52V 1.25A power supply.
Individual Features:
4-port PoE switch supports 1 10/100M self-adaptive RJ45 UpLink port and 4
10/100M self-adaptive PoE RJ45 ports.
4-port PoE switch with max 65W total power consumption.
8-port PoE switch supports 1 10/100M self-adaptive RJ45 UpLink port and 8
10/100M self-adaptive PoE RJ45 ports.
8-port PoE switch with max 96W total power consumption.
Typical Application
The typical application of the device is shown in Figure 1-1
Device Structure
4-Port PoE Switch
Front Panel
The front panel is shown in Figure 2-1.
| SN | Name | Note |
|---|---|---|
| 1 | Ethernet Ports | 4 10/100M self-adaptive RJ45 PoE ports. 1 UpLink Port. |
Back Panel
The back panel is shown in Figure 2-2
| SN | Name | Note |
|---|---|---|
| 1 | Power/PoE Max | Indicates the switch is powered on and if the maximum PoE |
power available is used
2| Ground| Used as grounding option for the switch
3| DC| Power connection port. Supports 52V 1.25A
Sheet 2-2
PoE Power Output
10/100M RJ45 PoE Ports support IEEE802.3af and IEEE802.3at power standards.
Supports simultaneous power to 2 ports using IEEE802.3t and 4 ports using
IEEE802.3af. Total power draw cannot be over 65W.
8-Port PoE Switch
Front Panel
The front panel is shown in Figure 2-3.
| SN | Name | Note |
|---|---|---|
| 1 | 1, 2, 3, 4, 5, 6, 7, 8 | 8 10/100M self-adaptive RJ45 PoE ports |
| 2 | 9(Uplink) | 10/100M self-adaptive RJ45 port. |
| 3 | Power | Power connection port. Supports 52V 1.85A. |
Sheet 2-3
Back Panel
The back panel is shown in Figure 2-4.
| SN | Name | Note |
|---|---|---|
| 1 | PWR | Indicates the switch is powered on. |
| 2 | 9(Uplink) | Port Status LED. Blinking – data transmitting. Solid – link |
established. Off – no connection.
3| 1, 2, 3, 4, 5, 6, 7, 8| Port Status LEDs. Blinking – data transmitting.
Solid – link established. Off – no connection.
4| PoE Status| This row of LEDs indicates if PoE is being used.
5| PoE MAX| Indicates if the maximum PoE power available is used.
6| VLAN| When enabled, communication is isolated between downlinks and uplink.
Downlinks do not communicate with each other.
Sheet 2-4
PoE Power Output
10/100M RJ45 PoE Ports support IEEE802.3af and IEEE802.3at power standards.
Supports simultaneous power to 3 ports using IEEE802.3t and 8 ports using
IEEE802.3af.
Total power draw cannot be over 96W.
Appendix 1 Technical Specification
| TECHNICAL PARAMETERS | AMPS5E4P-AT-65 | AMPS9E8P-AT-96 |
|---|
Physical Port
Network Ports| 110/100 Base-T (UpLink)
410/100 Base-T (POE powered)| 110/100 Base-T (UpLink)
110/100 Base-T (UpLink)
Technical Index
Exchange Capacity| 1.0Gbps| 1.8Gbps
Packet Forwarding Rate| 0.74Mpps| 1.34Mpps
Exchange Mode| Store & forward|
MAC Study| MAC auto study, address list capacity 2K|
Power Pin Assignment| Endspan 12(+) 36(-)|
Common Parameter
Indicator| Power, PoE Max, PoE, Link/Act|
Power| DC52V 1.25A power adapter| AC 100-240V Input, 50/60Hz
Power Consumption| ≤65W| ≤96W
Application Humidity| 10%～90%|
High &Low Temperature| -10⁰C～45⁰C|
Weight| 730g| 1.1kg
Dimension| 94mm(L) 71mm(W) 26mm(H)| 171mm(L) 98mm(W) 27mm(H)
Learn more at
www.amcrest.com
2019 © Amcrest Technologies . All rights reserved.
16727 Park Row Houston,
TX 77084-5020
Phone: +1 888 212 7538
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>