TIMEX 75322T Atomic Wall Clock Instruction Manual
- June 7, 2024
- Timex
Table of Contents
Atomic Wall Clock
with the calendar and indoor temperature
Instruction Manual
Package Contents:
- Atomic Wall Clock
- Instruction Manual
What You Need:
- [2] AA batteries see “install Batteries”
Thank you for purchasing this TIMEX® product. Please read this manual in
its entirety to fully enjoy the benefits and features of this product. Please
keep this manual for future reference.
NOTE: A clear film is applied to the LCD at the factory that must be
removed prior to using this product. Locate the clear tab and simply peel to
remove.
SECTION 1 • SETUP
Install Batteries
Remove the battery compartment cover and install 2 fresh “M” batteries as
shown here.
Basic Setup
After installing batteries, it is recommended that you set the clock and
calendar initially. After the atomic clock signal is acquired, which may take
up to 24 hours, the clock accuracy and daylight saving time changes will be
automatically maintained.
About the Atomic Clock
A clock is considered atomic if it has an accuracy of one second in a million
years. Consumer clocks are considered atomic if they attain this accuracy by
receiving a signal from an atomic clock. In North America, the National
Institute of Standards and Technologies operates an atomic clock in Colorado
which transmits the time codes via the radio station WWVB. The TIMEX®clock you
have purchased includes a built-in receiver that picks up the signal from the
WWVB station. For the best possible reception, place the main unit with the
backside facing Colorado. NOTE: Due to solar radiation in the atmosphere, the
atomic clock signal is weaker during the day. Most synchronization with the
WWVB atomic clock signal happens at night when there is less interference.
Initial Set-Up
After power-up, the display will show all segments for 3 seconds. The display
will read 12:00 pm Jan 1, 2000, with room temperature and flashing The time
zone will default to PST [Pacific Standard Time!.
The Atomic Clock will start to search for the atomic signal.
If a valid signal is available, the Atomic clock will receive the local time
in 3-5 minutes.
The full-strength signal bars will appear on the display.
If the signal is not available when setting up, you may enter the present time
and date by following the manual setup.
Manual Set Up
To set the time and day/date:
If the icon is flashing, press the button to stop the Atomic clock from
searching for a signal.
Press and hold the SET button for 3 seconds to begin manual setup mode.
-
Select 12 or 24 hours [standard or military]. Press SET to confirm
-
The HOUR will flash.
Adjust the hour by pressing the+ or – button. Press SET to confirm -
The MINUTE will flash.
Adjust the hour by pressing the+ or – button. Press SET to confirm -
The YEAR will flash [20001.
Adjust the year by pressing the+ or – button. Press SET to confirm -
The MONTH will flash.
Adjust the month by pressing the+ or – button. Press SET to confirm -
The DATE will flash.
Adjust the date by pressing the+ or – button. Press SET to confirm -
The DST will flash.
Adjust the DST on or off by pressing the+ or – button.
Press SET to confirm
Button Functions
-
SET
Hold the SET button for 3 seconds to enter clock and calendar setting mode.
Set sequence: 12/24 > Hour> Minute >Year> Month > Date> DST -
+/ ZONE
Press to select the current Time Zone:
PST= Pacific Time
MST= Mountain Time
CST= Central Time
EST= Eastern Time
During the CLOCK setting, press the [+I button once for 1 step advance or hold for the fast scroll.
Hold +/ZONE button for 3 seconds to enter into Daylight Saving Time setup mode -
Atomic signal search)
Press to get a manual synchronization of the atomic time signal. -
(-) C/F
During CLOCKsettings, press 1-1button once for 1 step backward or hold for the fast scroll. In normal mode, press 1-1key to select °C and °F
Troubleshooting
Problem
|
Possible Solution
---|---
Bad Atomic Clock Reception no bars| Relocate the main unit. It is important
that the backside of the clock is facing the state of Colorado for optimum
reception. Make certain there are no large stone or metallic surfaces
disrupting the signal line-of-sight to Colorado. Make sure the main unit is
placed at least 3 feet [0.91 ml from other electronic appliances and devices
that may interfere with the wireless communication [such as TVs, microwaves,
computers, etc]. Large metallic surfaces will interfere with the atomic clock
signal.
Display Not Working| Make certain that the batteries are installed correctly.
The batteries may need replacing.
SECTION 2 • PRODUCT SPECIFICATIONS
Measurement Ranges
Indoor Temperature 32°F to 122°
Specifications
Power Requirements
Main Unit: 2 x “M’ alkaline or lithium batteries
Atomic Clock
Frequency: WWVB 60Khz Synchronizes Daily
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY
AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device
prior to battery installation. Remove batteries from equipment that is not to
be used for an extended period of time. Follow the polarity[+/-] diagram in
the battery compartment. Promptly remove dead batteries from the device.
Dispose of used batteries properly. Only batteries of the same or equivalent
type as recommended are to be used. DO NOT incinerate used batteries. DO NOT
dispose of batteries in fire, as batteries may explode or leak. DO NOT mix old
and new batteries or types of batteries [alkaline/standard]. DO NOT use
rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT
short-circuit the supply terminals.
Please DO NOT return the product to the retail store.
For technical assistance and product return information, please call Customer
Care: 877-221-1252 Mon. – Fri. 8:00
A.M. to 4:45 P.M. [CST]
www.chaneyinstrument.com
LIMITED WARRANTY-INTERNATIONAL – Consumer may have more remedies at law
than follows.
Chaney Instrument Co. warrants to the owner, this product are free from
material and workmanship for one year from the date of purchase. Chaney
Instrument shall NOT BE LIABLE FOR ANY ACCIDENTAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, WHETHER ARISING IN CONTRACT OR TORT. Chaney instruments obligation
(at ifs option) is limited to repair or replace this product. For in-warranty
repair, send the product, accompanied by Guarantee, bearing Dealer”s name and
date of purchase, with $5.00 to cover handling and postage to:
Timex®is a registered trademark of Timex Corporation in the U.S.
and other countries **Manufactured and serviced by Chaney Instrument Co.**
Lake Geneva, WI 53147
www.chaneyinstrument.com
© 2010 Chaney Instrument Co.
To receive product information, register your product online. It’s quick and
easy!
Log on to http://www.chaneyinstrument.com/product_reg.htm
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>