SMOOTHSKIN bare Ultrafast IPL Laser Permanent User Guide
- June 3, 2024
- SMOOTHSKIN
Table of Contents
- bare Ultrafast IPL Laser Permanent
- THE SMOOTHSKIN BARE FIT SYSTEM
- HOW DOES SMOOTHSKIN BARE FIT WORK
- IMPORTANT SAFETY INFORMATION
- POTENTIAL RISKS, SIDE EFFECTS AND SKIN REACTIONS
- BENEFITS OF USING SMOOTHSKIN BARE FIT
- WHAT IS THE INTENDED USE OF SMOOTHSKIN BARE FIT
- YOUR SUITABILITY
- HOW TO USE SMOOTHSKIN BARE FIT
- THE SKIN CONTACT SENSOR
- THE PRECISION HEAD
- CLEANING, MAINTENANCE, STORAGE
- TRAVELLING WITH SMOOTHSKIN BARE FIT
- TROUBLESHOOTING
- WARRANTY
- LABELS AND SYMBOLS
- TECHNICAL SPECIFICATIONS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
IPL USER GUIDE
10 minutes and voilà!
bare Ultrafast IPL Laser Permanent
WELCOME TO
SMOOTHSKIN BARE FIT!
Congratulations! You’ve opened up a world of unparalleled beauty, smoothness
and convenience.
Come and join in the conversation at
www.smoothskin.com where you can find expert
advice and support throughout your treatment.
THE SMOOTHSKIN BARE FIT SYSTEM
Package Contents
Inside the packaging of the SmoothSkin Fit you will find the following:
- Handset and Power Supply
- Mains Power Cable
- Precision Head
- User Manual
HOW DOES SMOOTHSKIN BARE FIT WORK
HOW DOES IPL WORK
SmoothSkin Bare Fit is designed to help break the hair cycle. Light energy is
transferred through the skin’s surface and is absorbed by melanin present in
the hair shaft. That light energy is converted to heat energy (below the
surface of the skin), which stops the hairs from growing back. Now you can
look forward to seeing the treated hairs naturally fall out over the course of
a few days to 1-2 weeks.
IMPORTANT SAFETY INFORMATION
CONTRAINDICATIONS
DO NOT use SmoothSkin Bare Fit if you have very dark skin. The skin tone
sensor located near the output window of the device will determine the tone of
your skin. If the skin tone sensor determines that your skin is too dark for
safe use, operation of SmoothSkin Bare Fit will be prevented.
DO NOT use SmoothSkin
Bare Fit if your skin has been artificially or naturally tanned or is burned
from sun overexposure. Your skin may be extra sensitive following sun exposure
and particularly susceptible to burning, blistering, discolouring or scarring
if you use SmoothSkin Bare Fit. Wait 1 week until sunburn or tan disappears
before using SmoothSkin Bare Fit.
DO NOT expose treated areas to the sun. Wait at least 7 days after treatment
before exposing treated skin to direct sunlight. Your skin may be extra
sensitive following SmoothSkin Bare Fit treatment and particularly susceptible
to sunburn. Apply sunscreen (SPF 15 or greater) to the treated area or cover
the treated area with suitable clothing.
DO NOT use SmoothSkin Bare Fit directly on the nipples, genitals or around the
anus. These areas may have a darker skin colour and/or greater hair density.
Using the device in these areas may cause discomfort/pain or injure (burn,
discolour or scar) your skin.
DO NOT use SmoothSkin Bare Fit if you have a history of skin cancer or pre-
cancerous lesions (e.g. nevi or a large number of moles).
DO NOT use on blisters and scars
DO NOT use SmoothSkin Bare Fit if you are pregnant, lactating, as this device
has not been tested with these individuals.
DO NOT use SmoothSkin Bare Fit on dark brown or black spots such as
birthmarks, moles or warts in the area you wish to treat. Using SmoothSkin
Bare Fit may injure your skin or make existing conditions worse. You may
experience side effects such as burns, blisters and skin colour changes or
scarring.
DO NOT use SmoothSkin Bare Fit if you have any skin condition in the treatment
area, including psoriasis, vitiligo, eczema, acne, herpes simplex or active
infections or wounds.
DO NOT use SmoothSkin Bare Fit if you are under the age of 18 as this device
has not been tested on these individuals.
WARNINGS
EYE SAFETY
SmoothSkin Bare Fit emits flashes of Intense Pulsed Light. Direct exposure is
potentially harmful to your eyes. Take care to follow the safety precautions
below.
WARNING: Possible eye injury (Potentially leading to loss of vision) or skin
injury if instructions are not followed. Read and follow the instructions.
The handset can only be activated (flashed) if the skin tone snesor (next to
the treatment window) detects a valid skin tone reading and is in full contact
with the treatment area. However:
DO NOT look directly into the treatment window of the handset when the system
has electrical power and is switched on.
DO NOT attempt to activate (flash) the system towards the eye.
DO NOT treat areas around the eye (eyebrows or eyelashes). Misuse can lead to
eye damage, protect eye from exposure. DO NOT use the appliance over the eye
lids or close to the eye.
ONLY attempt to activate (flash) the system when the front of the handset is
in good contact with the area you wish to treat.
WE RECOMMEND you look away from the handset when firing onto your skin.
ELECTRICAL AND SAFETY
As with any electrical device, certain precautions must be taken in order to
ensure your safety. DO NOT try to open SmoothSkin Bare Fit, as this may expose
you to dangerous electrical components.
DO NOT use if SmoothSkin Bare Fit is damaged; for example, cracked Handset,
cable damage (internal wires visible), cracked or broken glass on the handset,
etc. This may result in injury.
DO NOT use near bathtubs, showers, basins or other vessels containing water.
If SmoothSkin Bare Fit becomes wet, it should not be used.
DO NOT use if SmoothSkin Bare Fit becomes uncomfortably hot to touch. This may
indicate that the unit is damaged.
DO NOT use a power supply or other component, other than those provided for
use with SmoothSkin Bare Fit. This may damage the unit and cause it to stop
working.
DO NOT attempt to activate (flash) SmoothSkin Bare Fit onto any surface other
than skin.
WARNING: no modification of this equipment is allowed.
DO NOT position SmoothSkin Bare Fit so that it is difficult to disconnect from
the mains supply.
GENERAL SAFETY
DO NOT use if you have had a skin peel treatment on the area you wish to
treat. Please wait 30 days after a skin peel before treating with SmoothSkin
Bare Fit.
Treating tanned skin with Intense Pulsed Light (IPL) may result in permanent
Hyperpigmentation (Darkening) or Hypopigmentation (lightening) of the treated
skin.
DO NOT use on areas where you have tattoos or permanent make up.
DO NOT use If you have a known sensitivity to sunlight (photosensitivity) or
are taking medication that makes the skin more sensitive and causes
photosensitivity, e.g. Retin A, Accutane and/or other topical retinoids.
Always check the instruction leaflet that comes with your medicinal product,
to see if photosensitivity is listed as a side effect. Use of SmoothSkin Bare
Fit on photosensitive skin could result in skin damage such as swelling or
blisters. Seek medical advice prior to application of the appliance as use may
harm the skin.
This appliance is not intended for the treatment of medical conditions.
Medical advice should be sought to address, for example, moles, skin rash,
itchy skin, skin fungus or infection, skin bumps, or skin tags.
SmoothSkin Bare Fit should not be used over any fillers or botox.
SmoothSkin Bare Fit should be kept out of the reach of children under 18 years
of age. Children should not use, play with, maintain or clean the device.
There are a number of potential risks –exposure to the light output causing
burns or eye damage, electrocution, strangulation from the cables, choking
from the removable front.
SmoothSkin Bare Fit should be kept out of reach of pets and pests which could
damage the device. Potential risks include reduced function and electrocution.
SmoothSkin Bare Fit is not intended for use by persons with reduced physical,
sensory or mental capabilities. Unless they have been given supervision or
instruction concerning safe and proper use of the device by a person
responsible for their safety.
The SmoothSkin Bare Fit glass filter is a critical component that will get hot
during use. DO NOT touch the filter during or directly after use. Regularly
inspect the filter for damage.
DO NOT use SmoothSkin Bare Fit if the filter is cracked or missing.
Ensure that SmoothSkin Bare Fit treatment window is clean and free from
debris. Any debris on or around the treatment window during operation may
result in temporary skin changes such as redness or swelling.
WARNING: Damage of the skin may occur after prolonged or repeated surface
application on one site. Avoid over-usage which included excessive passes,
stacking of pulses and/or increased frequency of use.
WARNING: Do not override the safety mechanisms inherent to the device.
DO NOT exceed the usage specified in the treatment regime.
PRECAUTIONS
Hair removal by lasers or intense pulse light sources can cause increased hair
growth in some individuals. Based upon currently available data, the highest
risk groups for this response are females of Mediterranean, Middle Eastern,
and South Asian heritage treated on the face and neck.
DO NOT use SmoothSkin Bare Fit on any area where you may want hair to grow
back.
DO NOT use your SmoothSkin Bare Fit device on man’s face, jaw, or neck. The
hair in a man’s beard area is too dense, and using SmoothSkin Bare Fit device
in these areas may result in skin injury.
SmoothSkin Bare Fit is not recommended for use on red, grey, white or blonde
hair. SmoothSkin Bare Fit is not effective on these hair colours.
POTENTIAL RISKS, SIDE EFFECTS AND SKIN REACTIONS
Use of the SmoothSkin Bare Fit could result in side effects. The table below lists the known skin reactions that may occur following treatment with the SmoothSkin Bare Fit.
POSSIBLE SIDE EFFECTS | HOW TO ASSESS AND REACT |
---|---|
Mild pain / discomfort in the area being treated. | This is expected and is |
normal for all IPL treatments. You can keep on using the device as instructed,
and the pain should diminish with continued use.
Warm feeling or tingling sensations during treatment, which typically
disappear after a few seconds to a minute and decrease with continued use.|
This is expected and is normal for all IPL treatments. You can keep on using
the device as instructed.
Itchiness in the treatment area.| This is quite common for IPL treatments, and
should subside after a short period. You can keep on using the device as
instructed. Do not scratch the area.
Skin redness during or after treatment which disappears within minutes.| This
is expected and is normal for all IPL treatments. You can keep on using the
device as instructed once skin redness has disappeared.
Skin redness which does not disappear within minutes and lasts 24-48 hours.|
Stop using the device immediately and consult your physician before using it
again.
Pain or discomfort that is intense during treatment or persists after a
treatment.| Stop using the device immediately and consult your physician
before using it again.
IN VERY RARE CASES| HOW TO ASSESS AND REACT
---|---
Swelling and redness that does not disappear within two to three days.| Stop
using the device immediately and consult your physician before using it again.
Temporary changes in skin colour (lightening or darkening).| If your skin
colour changes, stop using the device immediately and consult your physician.
Blistering, scarring or burning of the skin.| Stop using the device
immediately and consult your physician before using it again. Apply a cold
pack to the area. Treat with antiseptic or burn cream.
In a clinical trial of 50 subjects, each subject received 12 weekly treatments. The recorded effects were:
- Itchiness – 3 subjects experienced mild itchiness after treatment.
- Slight Redness – This was reported by 2 subjects.
- Mild Stinging Sensation – 5 subjects reported mild discomfort following treatment.
- In-growing Hair – 1 subject reported experiencing an in-growing hair following treatment.
- Follicle Redness – 1 subject reported a red spot at the treatment site following treatment.
In all cases, the treated skin returned to normal within 7 days.
BENEFITS OF USING SMOOTHSKIN BARE FIT
The SmoothSkin Bare Fit is indicated for the permanent reduction of unwanted
hair.
A clinical trial was performed to assess both the safety and efficacy of the
SmoothSkin Bare Fit. The key features of the clinical trial were:
- All treatments were performed by non-medically trained operators at a single location using devices identical to the SmoothSkin Bare Fit provided in this package;
- All subjects were required to complete questionnaires related to their general health and those who could not be treated, e.g. those who had one or more of the contraindications as listed in Section 3 of this User Manual were excluded. In addition, all subjects were required to provide Informed Consent as per international clinical trial requirements;
- A total of 53 female subjects, aged between 19 and 45 years old, commenced the trial;
- Three subjects left the trial during the treatment period for personal reasons. No subjects left the trial due to problems associated with the use of the SmoothSkin Bare Fit;
- Each subject received 12 weekly treatments to their chosen body location. A typical treatment consisted of shaving the site then applying the SmoothSkin Bare Fit following the same process as outlined in Section 8,, Step 3 of this user manual;
- Hair counts were used to measure the change in the amount of hair 6 months after the last treatment and 12 months after the last treatment. The hairs in the treatment sites were counted via high resolution photography and the difference in hair counts was calculated as a percentage change;
- When used as directed, the clinical trial participants showed on average 44% less hair 6 months after their last treatment and 36% less hair 12 months after their last treatment when compared to hair counts taken before treatment (See Table below). Actual results did vary from person to person;
| SmoothSkin Bare Fit
---|---
Number of Subjects at 6 Months Post Treatment| 50
Hair Reduction at 6 Months Post Treatment| 43.90%
Number of Subjects at 12 Months Post Treatment| 33
Hair Reduction at 12 Months Post Treatment| 36.00%
% of Subjects met success (>30% hair reduction) on all body areas at 12 months
post-treatment. Subject Success is defined as greater than 30% hair reduction
at all treatment sites at 12 months.| 66.70%
- The incidence of side effects during the clinical trial was minimal (as outlined in Section 4 above) and the majority of subjects (48 out of 50) would recommend the SmoothSkin Bare Fit to their friends.
WHAT IS THE INTENDED USE OF SMOOTHSKIN BARE FIT
INTENDED USE
SmoothSkin Bare Fit is intended for the permanent reduction in unwanted hair.
YOUR SUITABILITY
BODY AREAS
SmoothSkin Bare Fit is suitable for use on body hair and female facial hair
below the cheekline.
SKIN COLOUR
SmoothSkin Bare Fit is suitable for use on light, medium and dark skin tones
up to and including skin tone 5. SmoothSkin Bare Fit incorporates a Skin Tone
Sensor that measures the colour of your skin and will prevent use if your skin
tone is too dark.
HAIR COLOUR
SmoothSkin Bare Fit is suitable for use on naturally black or brown hair.
It may not be as effective on white, grey, blonde or red hair.
HOW TO USE SMOOTHSKIN BARE FIT
WARNING: Follow each step in the treatment process ensuring you complete
all aspects of each step before progressing to the next.
Step 1: PREPARE the area to be treated
Remove all visible hair by shaving. Make sure there is no hair remaining above
the surface of the skin as this may cause injury.
This also prevents debris from covering the front of your device.
Cleanse the treatment area and pat dry. Remember, don’t use any gels or creams
with this device!
Step 2: Doing a TEST PATCH
Before your first treatment on each new body area, we RECOMMEND you test your
skin in that area for a reaction to SmoothSkin Bare Fit. The patch test area
should be approximately 3cm x 2cm in size (equivalent to 2 flashes applied to
the skin side by side). Follow Step 3 to treat the area.
Wait 24 hours following the patch test, to ensure your skin is suitable for
treatment and there is no adverse reaction to the light energy. If there is no
reaction after 24 hours, you may treat the area around the patch test. The
‘patch tested area’ should NOT be re-treated for at least 1 week.
Step 3: Treating with SmoothSkin Bare Fit
a) Plug the Power Supply into an Electrical Outlet using the provided Power
Cable. The Skin Tone Sensor on the front of the Handset will illuminate blue
and the fan will start up.
STANDBY MODE Timeout
When the unit is left “inactive” i.e. no buttons are pushed for 10 minutes
then the unit will revert to STANDBY mode, and the STS lights will switch off.
To return to READY mode for treatment, press the Activation Button.
b) Press the Handset firmly against the area to be treated ensuring the Skin
Tone Sensor is in contact with the skin. If the Skin Tone Sensor does not
detect a valid skin tone, then the Handset cannot be activated. When the Skin
Tone Sensor measures a valid skin tone, the lights around the Activation
Button will illuminate WHITE to indicate the device is ready to flash.
c) Press the ACTIVATION BUTTON. The device will flash, and a warm sensation
should be felt.
d) Move the Handset to the next area to be treated and repeat. The device
needs to recharge between flashes. This will only take about 0.6 seconds.
e) Ensure that the ENTIRE AREA receives treatment, and treat any stubborn
areas (such as underarms) with multiple passes (running your device over the
same area a maximum of 3 times).
WARNING: Make sure not to cover the vents on the device whilst treating,
as this can lead to the device overheating.
SmoothSkin Bare Fit is an extremely fast and powerful device, allowing you to
complete a whole body treatment in under 10 minutes.
TREATMENT METHOD – STAMP OR GLIDE?
Stamp Method
This method is recommended for small areas such as the underarm and bikini
line. Place the Handset on the skin, press & release the Activation Button.
Remove from the skin before carefully re-applying to the next treatment area.
Glide method
This method is recommended for larger areas such as legs. Place the Handset on
the skin, hold down the Activation Button (press down continuously), then
glide the Handset along the skin between flashes. Try to move the Handset at a
steady speed that gives full coverage without overlap or missed areas.
Step 4: Your SmoothSkin Bare Fit Treatment Schedule
SmoothSkin Bare Fit should be used WEEKLY until the desired results are
achieved.
Step 5: Switching Off the SmoothSkin Bare Fit
When the treatment is finished, SmoothSkin Bare Fit should be unplugged from
the Electrical Outlet.
Refer to section 11 for details of how best to look after your SmoothSkin Bare
Fit.
THE SKIN CONTACT SENSOR
SmoothSkin Bare Fit is fitted with a skin contact sensor that checks your skin
contact before each flash, making sure the device is safe to operate! This
makes the device compliant with the most stringent safety regulations.
The skin contact sensor also ensures you get the best results from your
device. The sensor must be in full contact with the treatment area in order
for the device to flash.
This full contact with your skin means that all the light energy emitted from
the device reaches the treatment area to deliver the best results. If the
device is not in full contact with the treatment area, the device will not
fire. Try adjusting the positioning of the device to ensure full contact is
achieved, particularly on more awkward areas like arms and shins.
THE PRECISION HEAD
SmoothSkin Bare Fit comes with a detachable precision head that is perfect for
smaller, tricky areas (like upper lip, fingers, and toes). This has the
benefit of giving you even more flexibility during each treatment.
Using the precision head will slow your device down a little, so we only
recommend using when needed, to ensure you get the fastest treatment possible.
The precision head simply attaches on to the front of your device via an
internal magnet inside the front of the main device. This magnet holds the
head in place whilst you treat the area. Simply unclip or re-attach depending
on what area you’re treating.
If the precision head is damaged or missing any parts (e.g. magnet or
reflector), then do not use.
If the precision head becomes uncomfortably hot during use, then stop
treatment until it has cooled down.
Follow all EYE SAFETY warnings (Section 3) when the precision head is fitted.
Follow the cleaning instructions (Section 11) for the precision head.
CLEANING, MAINTENANCE, STORAGE
After treatment, always switch off SmoothSkin Bare Fit by unplugging from the
electrical oulet.
After use, the handset, skin tone sensors and treatment window should be
inspected for damage and wiped down with a dry, lint free cloth.
WARNING: The glass filter can get hot during use. DO NOT touch or clean
the filter for at least 5 minutes after use to allow it to cool down.
NEVER use water or other cleaning fluids, as these can damage the device
leading to a potential safety hazard.
If necessary, the Reflector and Skin Tone Sensor can be carefully cleaned by
using a slightly damp cotton bud.
Store SmoothSkin Bare Fit in a
cool, dry place. Make sure that the treatment window and skin tone sensor on
the handset are protected from damage.
Regularly check the device (including cords) for visible signs of damage. In
case of damage or cracks, stop using the device -and visit the website for
support details.
TRAVELLING WITH SMOOTHSKIN BARE FIT
The Power Supply unit of the SmoothSkin Bare Fit is universal and will work
with all commonly encountered mains supplies.
Providing you have a suitable adaptor for the mains power cable plug, the
SmoothSkin Bare Fit will operate as normal.
TROUBLESHOOTING
PROBLEM | SOLUTION |
---|
The Activation Button Lights on the Handset do not light up when placedagainst
your skin.| Make sure the power supply is plugged in. Ensure the skin tone
sensor is fully pressed against the skin. Your skin could be too dark for
treatment. Check against the skin tone chart in the front of this user guide.
The Activation Button on the Handset lights up white when placed on the
skin, but the Handset fails to flash when the Activation Button is pressed.|
There could be a fault with the device. Unplug the device and restart. If the
problem persists, visit the website for support details.
The Activation Button Lights on the Handset are illuminated red
continuously, and the device will not function.| This indicates that there is
a fault with the device. Stop using the device and visit the website for
support details.
The SmoothSkin Bare Fit handset, treatment window, power supply or
cable are damaged, broken, cracked or appear defective.| DO NOT USE. If you
are in any doubt about the safety of SmoothSkin Bare Fit or suspect it is
damaged in any way, it must not be used, and you should visit the SmoothSkin
website for more information.
WARRANTY
We grant a 2 year warranty on the product starting on the date of purchase.
Within the warranty period, we will check faults in materials or workmanship
free of charge and replace the complete device, at our discretion.
This warranty extends to every country where this device is supplied by CyDen
or its appointed distributor.
This warranty does not cover damage due to improper use, normal wear or use as
well as defects that have a negligible effect on the value or operation of the
appliance. The warranty becomes void if repairs are undertaken by unauthorised
persons and if original SmoothSkin Bare Fit parts are not used. To obtain
service within the warranty period, please visit our website:
www.smoothskin.com
To obtain service within the warranty period, please visit our website:
www.smoothskin.com
LABELS AND SYMBOLS
SmoothSkin Bare Fit is marked with the following symbols:
| Type BF Applied Part| | NRTL Certification marking
---|---|---|---
| Class II Equipment| | FCC EMC compliancefor North America
| Follow Instructions for use| | Australia Regulatory Compliance Mark
****| WEEE waste disposal mark of the European Union| | Trefoil compliance
mark for Ukraine
| European Conformity Marking| | China RoHS environmental protection use
period
| Keep Dry| | Warning Optical Radiation from device may cause eye injury
FCC Statement:
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
TECHNICAL SPECIFICATIONS
The SmoothSkin Bare Fit is a filtered broadband Intense Pulsed Light system with the following technical specifications:
• Repetition Rate: | Manually pulsed every 0.6 seconds. Continuous operation |
---|---|
• Max Optical Output: | 4J/cm2 |
• Pulse Length: | 0.8 – 1.0msec FWHM |
• Wavelength: | 510-1100nm |
• Power Line Input: | 100–240V~, 50/60Hz,1.7-0.91A |
• Operating temperature: | Between 5°C and 40°C |
• Operating humidity: | Up to 93%R.H. non condensing |
• Operating Pressures: | 700hPa to 1060hPa |
• Treatment area (spot size): | 3 cm2 (30mm x 10mm) |
The area directly around the treatment window is classified as the Applied
Part, and can reach a maximum temperature of 52°C.
Ensure SmoothSkin Bare Fit is used as directed in Section 8.
TRANSPORT CONDITIONS:
• Temperature: | -25°C to +70°C |
---|---|
• Humidity: | Up to 93%R.H. non condensing |
• Pressures: | 500hPa to 1060hPa |
If the device has been stored at temperatures outside of the stated operating range, then please allow at least 30 minutes before use to allow the device to acclimatise.
SmoothSkin Bare Fit has unlimited flashes and is intended for a single user.
Minimum expected service life is 10 years when following the recommended
regimen.
EMC
SmoothSkin Bare Fit complies with the latest EMC Standards and Amendments
applicable to Household and Medical Devices.
These are: EN 60601-1-2:2014 Ed 4.0, EN 55014-1:2017 and EN 55014-2-2015, EN
61000-3-2:2014 & EN 61000-3-3:2013, FCC CRF 47 Part 15B 15.107 & 15.109
Safety
SmoothSkin Bare Fit complies with the latest Safety Standards and Amendments
applicable to Household and Medical Devices.
These are: IEC 60335-1:2010, IEC 60335-2-23 :2003, IEC 60601-11:2015 , IEC
60601-1-1:2005, IEC 60601-2-57:2011, IEC 606011-6:2010, IEC 62366-1:2015, IEC
62366-1:2015, IEC 62304:2006,
CAN/CSA -C22.2 No 60601-1:2008 and 2014, ANSI/AAMI ES 60601-1:2005 +
AMS
CE marking certifies that this appliance conforms to the following EU
Directives:
- Low Voltage Directive 2014/35/EU
- Electromagnetic Compatibility Directive 2014/30/EU
- Energy-Related Product Directive 2009/125/EC
For further details contact CyDen Ltd
DISPOSAL (END OF LIFE)
This product is a medical device.
In order to minimize hazards to health and the environment and ensure that
materials can be recycled, this product should be disposed of at a separate
collection facility for waste electrical and electronic equipment.
The WEEE symbol marked on the product is there to remind you.
You can reach us via our SMOOTHSKIN web page at www.smoothskin.com
Manufacturer
CyDen Limited
Block A, Bay Studios Business Park
Fabian Way,
Swansea
SA1 8QB,
United Kingdom
CM12-1804-01
Type: SSB1/1 * Product may vary from illustrations shown throughout this guide
References
- SmoothSkin | THE WORLD’S MOST SOPHISTICATED PERMANENT HAIR REMOVAL TECHNOLOGY
- SmoothSkin | THE WORLD’S MOST SOPHISTICATED PERMANENT HAIR REMOVAL TECHNOLOGY
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>