Snap-on TPMS5 Tire Pressure Sensor System Tool Kit User Manual
- June 7, 2024
- Snap-on
Table of Contents
After selecting Verify IDs/DTC Codes, trigger each sensor of the
vehicle. In this example, the RR sensor is not triggering.
Continuing on to DTC Codes, ensure the OBDII Cable is connected to
the tool and vehicle with the ignition in the ON position, Then tap “OK”.
In this example, it shows that two codes are present. The first code
may be the issue regarding the sensor.
Continuing on to Verify IDs, this example shows that there is an ID
stored in the vehicle but triggering the sensor shows no sensor detected. The
sensor needs to be replaced.
Continuing on to Repair, selecting either Replace or Relearn will
take you to that screen at the main TPMS function where you can program a
sensoror perform a relearn
In this example, programming a new sensor is needed. From the
program screen, a new sensor can be programmed, and a relearn can be performed
if necessary. See section B-4 for programming, and B-2 for relearns
Note : If all sensors appear on the Verify IDs screen but the IDs do not match, a relearn is necessary to match the IDs.
D – Settings
Within the Settings function, a variety of customizable settings can be changed for user preference. Each setting is described in the next section.
Profile| Change internal tool information including Company Name, Address, and
Phone Number.
---|---
Date and Time| Change Date and lime settings including Date, lime, Time Zone,
set automatic Date and Time On/Off.
Language| Change between 10+ Languages including English, Spanish, French, and
more.
Region| Change Region from North America, Europe, Australia, or Japan.
Units| Change Pressure (PSI, Bar, kPa) and Temperature (°F, °C) units.
Sensor ID Format| Change Sensor ID Formats from Decimal (0-9), Hexadecimal
(A-F 0-9), or Auto.
Screen Brightness| Change Screen Brightness from 20%-100%.
Sound| Change Sound settings including Beep (On/Off), and Vibration (On/Off).
Auto OFF| Change Auto OFF settings from 10min-60min or Off completely.
WiFi Setup| Change Wifi Settings by scanning for available networks and
connecting. (This setting is necessary for WiFi Updating and Emailing).
Factory Reset| Erase all data from the tool and return it to factory settings.
WARNING: This will remove all Jobs, settings, and update information from
the tool
About| View various tool information including Serial Number, Version,
Copyright information, and more.
E – History
Within the History function, view all saved jobs in the tool and revisit them. Jobs will be listed in order by date and will display customer name and vehicle Make, Model, and Year.
F – Training
Within the Training function, view a TPMS troubleshooter that takes the user through common TPMS issues to reach a solution. As well as an in-depth Demo mode that takes the user step-by-step through the main TPMS functio.
Troubleshooter
Troubleshooter allows the user to diagnose common TPMS issues. The function will ask common questions to guide the user to a solution. Tap each answer as it applies, and the tool will take the user to the screen necessary.
Demo
Demo mode takes the user step-by-step through the main TPMS function. From the
main menu, all the way down to sending an email, the user can Demo the tool.
Use this mode for practice or training purposes.
Note : this mode is for Demo purposes only, any information that appears
on-screen are examples and information may not match certain situations.
Chapter 3:
Updating
The TPMS5 can be updated directly through WiFi. Ensure the tool is plugged in and charging whenever performing an update.
A. via WiFi Connection
| 
---|---
| 
---|---
| 
---|---
| 
---|---
| The Tool will
begin updating, DO NOT interrupt this process. Once finished, the tool will
restart and it will be on the latest software version.
---|---
chapter 4:
Warranty/Service and Repair
Snap-on Tools Company Limited One (1) Year Warranty
Snap-on Tools Company (the “Seller”) warrants only to original purchasers who use the Equipment in their business that under normal use, care and service, the Equipment (except as otherwise provided herein) shall be free from defects in material and workmanship for one year from the date of riginal invoice. Seller does not provide any warranty for accessories used with the Equipment that are not manufactured by Seller. SELLER’S OBLIGATIONS UNDER THIS WARRANTY ARE LIMITED SOLELY TO THE REPAIR OR, AT SELLER’S OPTION,
REPLACEMENT OF EQUIPMENT OR PARTS WHICH TO SELLER’S SATISFACTION ARE
DETERMINED TO BE DEFECTIVE AND WHICH ARE NECESSARY, IN SELLER’S JUDGMENT, TO
RETURN THIS EQUIPMENT TO GOOD OPERATING CONDITION. NO OTHER WARRANTIES,
EXPRESS OR IMPLIED OR STATUTORY, INCLUDING WITHOUT LIMITATION ANY IMPLIED
WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AND ALL
SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED.
SELLER SHALL NOT BE LIABLE FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL COSTS
OR DAMAGES INCURRED BY
PURCHASERS OR OTHERS (including, without limitations, lost profits, revenues,
and anticipated sales, business opportunities or goodwill, or interruption of
business and any other injury or damage).
This Warranty does not cover (and separate charges for parts, labor and related expenses shall apply to) any damage to, malfunctioning, inoperability or improper operation of the Equipment caused by, resulting from or attributable to (A) abuse, misuse or tampering; (B) alteration, modification or djustment of the Equipment by other than Seller’s authorized representatives; (C) installation, repair or maintenance (other than specified operator aintenance) of the Equipment or related equipment, attachments, peripherals or optional features by other than Seller’s authorized representatives; (D) mproper or negligent use, application, operation, care, cleaning, storage or handling; (E) fire, water, wind, lightning or other natural causes; (F) adverse nvironmental conditions, including, without limitation, excessive heat, moisture, corrosive elements, dust or other air contaminants, radio frequency nterference, electric power failure, power line voltages beyond those specified for the Equipment, unusual physical, electrical or electromagnetic stress nd/or any other condition outside of Seller’s environmental specifications; (G) use of the Equipment in combination or connection with other equipment, attachments, supplies, or consumables not manufactured or supplied by Seller; or (H) failure to comply with any applicable federal, state or local regulation, requirement or specification governing emission analyzers and related supplies or consumables. Repairs or replacements qualifying under this Warranty will be performed on regular business days during Seller’s normal working hours within a reasonable time following purchaser’s request. All requests for warranty service must be made during the stated warranty period. Proof of purchase date is required to make a Warranty request. This Warranty is nontransferable.
TPMS5 Technical Support and Service
US SERVICE AND TECH SUPPORT
35990 Industrial Road,
Livonia, Michigan 48150
844-349-8767| CANADA SERVICE AND TECH
SUPPORT
4-2355 Royal Windsor Drive, Mississauga,
Ontario L5J 4S8
855-455-8767
---|---
Email: support@tpmsconnect.com
Assembled in Taiwan
Snap-on is a trademark, registered in the United States and other countries,
of Snap-on Incorporated.
©2020 Snap-on Incorporated. All Rights Reserved. All other marks are
trademarks of their respective holders.
Snap-on, 2801 80th Street, Kenosha, WI 53143
www.snapon.com
Patents: See https://patents.snapon.com
EU Declaration of Conformity
Product Model/Product
Product Name : Tire-pressure monitoring system
Model Name : TPMS5
Name and address of the manufacturer or his authorized representative:
ATEQ INSTRUMENTS (ASIA) PTE LTD.TAIWAN BRANCH (SINGAPORE) NO.3, LANE 223, SAN
JIA DONG STREET, 40642, TAICHUNG, TAIWAN
This declaration of conformity is issued under the sole responsibility of the manufacturer.
The objection of the declaration
Tire-pressure monitoring system
The object of the declaration described above is in conformity with the
relevant Union harmonization legislation:
Radio Equipment (RED) Directive 2014/53/EU
6. References to the relevant harmonized standards used or references to the
other technical specifications in relation to which conformity is declared:
RED: EN 300 328 V2.2.2, EN 301 893 V2.1.1, EN 300 330 V2.1.1, EN300 220-1
V3.1.1, EN300 220-2 V3.2.1
7. Additional information:
Signed for and on behalf of:
ATEQ INSTRUMENTS (ASIA) PTE LTD.TAIWAN BRANCH (SINGAPORE)
Taichung, Taiwan 2020/8/19
Roger Lin / RD Manager
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>