INSIGNIA USB-C VR Headset Cable NS-VR5MCC User Guide
- June 7, 2024
- Insignia
Table of Contents
QUICK SETUP GUIDE
USB-C VR Headset Cable
NS-VR5MCC
PACKAGE CONTENTS
- USB-C VR Headset Cable
- Quick Setup Guide
SYSTEM REQUIREMENTS
Compatible with the Oculus Quest and Oculus Quest 2 VR headsets
FEATURES
- Designed specifically for use with select Oculus devices, including the Oculus Quest and Oculus Quest 2
- The durable cable can withstand the physical demands of full-motion VR devices
- Thin, flexible 16.4 ft (5 m) cable with a right-angle connector gives you ample space for movement while using a VR headset
- Active fiber USB-C to USB-C cable provides full-speed 5 Gbps data transfer for a better gaming experience
USING THE CABLE
-
Plug the 90° end of your cable in to a VR headset, then connect the other end in to a computer with a USB-C port.
-
To charge other devices, plug the 90° end of your cable in to a charging source (not included), and the other end in to the selected device with a USB-C port. Make sure that the device requires 20V/3A (60 W) or less.
Note: This cable can also be used as a standard USB-C to USB-C cable, however, due to its unique connector design and construction for use with VR headsets, there may be compatibility issues in certain situations.
Before using your new product, please read these instructions to prevent any damage.
TROUBLESHOOTING
Charging or data transfer problems
- Make sure that the cable is plugged in securely.
- If your device charges too slowly, make sure that the device requires less than 20 V at 60 W.
- If your device has a protective covering, the 90° connector may not make good contact. If the space surrounding the USB-C port on the device is limited, the cable may not work. Try using the straight connector.
SPECIFICATIONS
- Dimensions (length) : 16.4 ft. (5 m)
- Data rate: 5 Gbps
- Cable power limit: 20 V/3 A 60 W
About Active Optical Cables (AOC)
Due to the physical properties of copper wires, the speed and length at high-
speed transmission may be limited. In contrast, light signals suffer from much
less attenuation in optical fibers. Therefore, using a delivery module to
convert electrical signals into optical signals for transmission in optical
fibers, and then using a receiving module to convert the received optical
signals into electrical signals can result in the transmission of higher
quality data with longer and thinner cables. The USB 3.1 high-speed pair of a
USB-C optical fiber cable uses optical fibers for the transmission of data.
SAFETY INFORMATION
- This product can only be used for equipment below 60 W. This is an optical fiber product. It should not be bent 90° for storage, or the cable could be damaged. Otherwise, it may easily lead to product damage and dysfunction.
- Do not plug the cable into a non-USB-C interface, otherwise, the cable may be damaged
- Remove the cable from the device when it will not be in use for an extended period of time.
LEGAL NOTICES
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ICES-003
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
ONE YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 877-467-4289
(U.S. and Canada) or 01-800-926-3000
(Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its a listed company.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2020 Best Buy. All rights reserved.
V1 ENGLISH 20-0456
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>