VOXX APS57TM Vehicle Remote Start User Guide
- June 6, 2024
- Voxx
Table of Contents
APS57TM Vehicle Remote Start
APS57TM
Vehicle Remote Start / Keyless System
Installation and Reference Guide
Thank you for trusng Presge products! If you are a consumer, please note: Professional installation is strongly recommended.
This manual assumes the installer has adequate knowledge of the following experse. Therefore, it does not
cover these topics in detail:
·
12-volt electronics
·
Testing and verifying circuits
·
Making safe and lasting wiring connections
·
Factory ignition, power, lighting, data bus and sensing systems
·
Factory systems and components to avoid
·
Safe wire routing, circuit protection and product placement
·
Access to vehicle-specific technical information
In addion, this manual assumes the installer has the proper tools, skill and facilities to perform a professional installaon. Performing an improper installation could result in damage to the vehicle or its components, improper system function, unsafe vehicle operation or physical injury. Such instances would not be covered by the vehicle manufacturer’s warranty, nor by Voxx Electronics, Inc.
Detailed Descriptions
2 Wire Harness Colors and Functions
2
Power Connector
3
Noficaon Connector
4
Input / Output Connector
6 External Components
6
RF Antenna Kit
6
Data Bus Interface (DBI)
6
Telemacs
6
Weblink Programming
7 Setup Options
7
Remote Programming
8
Keyless Control
10
Remote Start Control
14 System Operation
14
Remote Operaon
Quick Reference
15 System Programming
15
Programming Mode Entry / Exit
16
Feature Bank Opons
17
Data Port Protocol
17
Tach Funcon
17
Alarm Override
18
Silent Lock and Unlock
18
User Selectable LED
18 System Diagnostics
18
Troubleshoong Remote Start
19 Wiring Diagrams
19
Door Lock Connecons
22
Full System Connecons
2020 Voxx Electronics Corporaon. All rights reserved.
APS57TM_RevD_07/20
Detailed Descriptions: Wire Harness Colors and Funcons
Power Connector (6-pin High-Current Connector) See page 22 for the full system
diagram.
These wires are listed in order of their placement in the harness connector.
135
246
1. YELLOW Starter Output for Remote Start (+) The YELLOW wire supplies
12-Volt (+) to the vehicle’s starter wire when remote start is enabled, and
turns off once the vehicle is started. Verification: This starter wire
registers 12-Volt (+) during engine crank.
2. GREEN Ignition 2 Output (+) At its default setting, the GREEN wire
supplies 12-Volt (+) to the vehicle’s secondary ignion wire during remote
start. Verification: If present, the secondary ignion wire registers 12-Volt
(+) when the vehicle is in ignion mode AND during engine crank. Note: This
wire can be programmed to perform a different funcon by changing its opons.
Refer to Bank 3, Feature 7 on page 10.
3. RED 12-Volt Input (+) The RED wire connects to the vehicle’s primary
12-Volt (+) wire to power the system. Verification: The power wire registers
12-Volt (+) at all mes. Note: Before making this connecon, remove all module
fuses unl the system is completely connected.
4. RED/WHITE 12-Volt Input (+) The RED/WHITE wire connects to the vehicle’s
secondary 12-Volt (+) wire to power the remote start funcon. Verification: The
power wire registers 12-Volt (+) at all mes. Note: Before making this
connecon, remove all module fuses unl the system is completely connected.
5. PURPLE Accessory Output (+) At its default setting, the PURPLE wire
supplies 12-Volt (+) to the vehicle’s accessory wire to power vehicle
accessories during remote start. Verification: The accessory wire registers
12-Volt (+) when the vehicle is running or in Accessory mode, but not during
engine crank or if the vehicle is off. Note: This wire can be programmed to
perform a different funcon by changing its opons. Refer to Bank 3, Feature 9
on page 10.
6. BLUE Ignition 1 Input / Output (+) The BLUE wire supplies 12-Volt (+) to
the vehicle’s primary ignion wire during remote start. This wire is also used
to sense vehicle ignion for the Programming Funcons Verification: The primary
ignion wire registers 12-Volt (+) when the vehicle is in ignion mode AND
during engine crank.
2
APS57TM_RevA_07/20
Detailed Descriptions: Wire Harness Colors and Funcons
Notification Connector (4-pin connector) See page 22 for the full system
diagram.
These wires are listed in order of their placement in the harness connector.
13 24
1. WHITE Parking Light Relay Output (Internal Relay Pin 30) At its default
setting, the WHITE wire supplies 12-Volt (+) or Ground (-) to the vehicle’s
park light wire based on the connecon of the relay input (WHITE/RED wire).
Verification: The vehicle parking light wire registers 12-Volt (+) or Ground
(-) when the park lights are turned on.
2. WHITE/RED Parking Light Relay Input (Internal Relay Pin 87) The
WHITE/RED connects to vehicle 12-Volt (+) or Ground (-) to supply the relay
output (WHITE wire). Verification for default setting: · If the vehicle
parking light wire registers 12-Volt (+) when the park lights are on, connect
the WHITE/RED wire to a
constant 12-Volt (+) vehicle wire. · If the vehicle parking light wire
registers Ground (-) when the park lights are on, connect the WHITE/RED wire
to a
reliable vehicle ground source.
3. YELLOW/BLACK Ignition Output to Alarm (+) The YELLOW/BLACK wire supplies
12-Volt (+) ignion output when the vehicle’s ignion is set to ON, but not
during the remote start runme. This output will be used when an external alarm
system is added to the vehicle.
4. BLACK Ground Input (-) The BLACK wire connects to a reliable vehicle
ground (-) source to power the system. Verification: The vehicle ground (-)
source wire registers ground (-) at all mes. Note: Before making this
connecon, remove all module fuses unl the system is completely connected.
APS57TM_RevA_07/20
3
Detailed Descriptions: Wire Harness Colors and Funcons
Input / Output Connector (14-pin connector) See page 22 for the full system
diagram.
These wires are listed in order of their placement in the harness connector.
1 3 5 7 9 11 13
2 4 6 8 10 12 14
1. BLACK/WHITE Horn Output (-) The BLACK/WHITE wire connects to the
vehicle’s horn wire and supplies Ground (-) when acvated from the system.
Verification: The vehicle horn wire registers Ground (-) when the horn is
acvated.
2. RED Door Lock (-) The RED wire supplies Ground (-) when the Lock funcon is acvated from the remote control or system. Verification: The vehicle lock wire registers 12-Volts (+) or Ground (-) when the Lock buon is acvated. Addional parts may be required. See Page 19 for common door lock wire diagrams.
3. GRAY/BLACK Hood Input (-) The GRAY/BLACK wire connects to the vehicle’s hood switch, or an installed switch that registers Ground (-) when triggered. Verification: The vehicle hood switch wire registers Ground (-) when the hood is opened.
4. GREEN Door Unlock (-) The GREEN wire supplies Ground (-) when the Unlock funcon is acvated from the remote control or system. Verification: The vehicle lock wire registers 12-Volt (+) or Ground (-) when the Unlock buon is acvated. Addional parts may be required. See Page 19 for common door lock wire diagrams.
5. LIGHT BLUE Remote Start Status Output (-) The LIGHT BLUE wire supplies Ground (-) as soon as the remote starter is acvated and remains acve unl 4 seconds aer remote start run me has ended. This wire is most commonly used to acvate data integraon modules.
6. DARK BLUE/BLACK — External Start Input (-) The DARK BLUE/BLACK wire connects to a device or switch that, when triggered, supplies a Ground (-) output. If the vehicle ignion is off, this input will acvate the remote start funcon.
7. BLACK/LIGHT GREEN Factory Arm Output (-) At its default setting, the BLACK/GREEN wire supplies a Ground (-) pulse when the system is armed and when the vehicle has been successfully started using remote start. It is typically used to re-lock vehicle doors aer remote start if necessary. Note: This wire can be programmed to perform a different funcon by changing its opons. Refer to Bank 3, Feature 21 on page 10.
8. BROWN/BLACK Brake Input (+) The BROWN/BLACK wire connects to the vehicle’s brake wire to supply brake status for remote start. Verification: The vehicle brake wire registers 12-Volts (+) when the brake is acvated.
9. BLACK/BLUE Factory Disarm Output (-) The BLACK/BLUE wire supplies a Ground (-) pulse when the system is disarmed and when remote start is acvated. Verification: In most vehicles the vehicle factory disarm wire registers Ground (-) if the driver door key cylinder is turned to the unlock posion. Note: This wire can be programmed to perform a different funcon by changing its opons. Refer to Bank 3, Feature 19 on page 10.
4
APS57TM_RevA_07/20
Detailed Descriptions: Wire Harness Colors and Funcons
Input / Output Connector (14-pin connector) (Cont.) See page 22 for the full
system diagram.
These wires are listed in order of their placement in the harness connector.
10. DARK BLUE Trunk Release Output (-) At its default setting, the DARK
BLUE wire connects to the vehicle trunk release wire or relay and supplies
Ground (-) when acvated from the remote control. Verification: The vehicle
trunk release wire registers 12-Volt (+) or Ground (-) when the trunk release
buon is acvated.
11. BLACK/RED Pulse After Shutdown Output (-) At its default setting, the
BLACK/RED wire supplies a Ground (-) pulse when the remote start system is
shut down. It is typically used to re-lock vehicle doors aer remote start
shutdown, or pulse the vehicle’s door trigger to turn off accessories aer
vehicle shutdown. Note: This wire can be programmed to perform a different
funcon by changing its opons. Refer to Bank 3, Feature 22 on page 10.
12. GREEN/YELLOW Diesel Glow Plug Input (+) The GREEN/YELLOW wire connect
to the vehicle’s Diesel Glow Plug detecon wire. Verification: This wire will
register as 12-Volt (+) while the Diesel Wait to Start Light is illuminated.
13. BLACK/YELLOW Pulse During Crank Output (-) At its default setting, the
BLACK/YELLOW wire supplies a Ground (-) pulse when the engine cranks during
remote start. Note: This wire can be programmed to perform a different funcon
by changing its opons. Refer to Bank 3, Feature 20 on page 10.
14. GREEN/ORANGE Tach Input The GREEN/ORANGE wire connects to the vehicle’s
tach wire at the negave side of the ignion coil or fuel injector to control
engine crank during remote start. Verification: · Using a voltmeter set to AC
volts, connect the voltmeter’s posive lead to a constant vehicle
12-Volts (+) source and the negave lead to the wire to be tested. · Start the
engine and have a partner slowly press the gas pedal while the transmission is
in Park. If the voltage
increases as the RPM increases, this is the proper tach wire.
APS57TM_RevA_07/20
5
Detailed Descriptions: External Components
RF Antenna / LED / Programming Port
The long-range antenna kit (included) plugs into a 6-pin connector on the
Presge module.
1. Mount the supplied antenna/receiver to a clear spot on the vehicle’s
windshield that will not block the driver’s vision. A suitable locaon is high
on the windshield near the rear-view mirror.
2. Be careful not to mount the antenna/receiver on any metallic window film,
as this will affect system range.
3. Route the antenna/receiver cable to the Presge module, ensuring it does
not block or interfere with deployment of the airbag (if equipped.) Plug into
the antenna port.
Data Bus Interface (DBI) Port
The 4-pin Data Bus Interface enables a FlashLogic door lock or transponder
interface to connect to and communicate with the vehicle data bus. The
combined system saves installaon me as many features that normally require
individual connecon can be accessed and controlled through the data bus.
Please refer to the D2D (Data to Data) funcon list available per vehicle at
www.FlashLogic.com.
FLCART Cartridge Port
This port is for installing the FlashLogic FLCART data immobilizer & door lock
interface cartridge used to communicate with the vehicle’s databus.
Weblink Programming Port
This 4-pin port is used for programming the FlashLogic FLCART interface
cartridge via the FLPROG Weblink or Weblink Mobile. Refer to the FlashLogic
website for more details.
FLCART Harness Port
This port is for the harness included with the FLCART interface cartridge.
Refer to the FlashLogic website for more details.
Telematics Interface
The 4-pin Telemacs port enables a connected interface such as CarLink to expand system control to a smartphone or
tablet. The following features may be able to be acvated from a connected device:
·
Door Lock Control
·
Remote Start
·
Trunk Release
·
Auxiliary Output*
·
Sliding Doors*
Weblink Programming This port can also be used to connect your FlashLogic Weblink for feature programming and soware updang. Once connected please visit www.flashlogic.com.
- Must be supported by FLCAN
6
APS57TM_RevA_07/20
Detailed Descriptions: Setup Opons
Bank 1: Add / Remove Remote Controls See page 15 for Programming Instrucon.
Remote programming is located in Feature Bank 1. This system will Auto Program
basic funcons of the remote with one (1) buon press. Basic funcons are
channels 1-3, Lock, Unlock, and Trunk / Start.
Feature Bank 1
1 Auto Program/Lock 2 Unlock 3 Trunk/Start
Descripon
Press Lock buon on remote Press Unlock buon on remote Press Start buon on
remote
CH.
To Auto Program a remote control:
1. Turn the ignion key to ON. 2. Press and release the valet buon three (3)
mes. 3. The system will beep one (1) me, indicang you have accessed Bank 1,
Remote Programming. 4. Press the Lock buon of each remote control you wish to
program. (Channels 1-3 of the remote control will be
programmed.) The system will beep one (1) me when each remote control is
added. 5. Turn the ignion key to OFF to exit programming mode, or cycle the
ignion key OFF/ON to advance to the next
Feature Bank.
To delete a remote control:
This system will store a maximum of four (4) remote controls in the memory.
Addional programmed remote controls will delete the oldest-programmed remote
control.
Deleting All Remotes: 1. Perform steps 1-3 above. 2. Press and hold the valet buon for five (5) seconds. 3. The system will sound one (1) long beep. This indicates all remotes have been deleted from memory.
Notes: ·
·
The system will store in the memory a maximum of four (4) remote controls. Addional programmed remote controls will delete the oldest-programmed remote control. During normal operaon, the Programmed Transmitter Notification (PTN) function indicates how many remote controls are programmed by flashing the LED a certain number of mes when the vehicle ignion is turned on.
APS57TM_RevA_07/20
7
Detailed Descriptions: Setup Opons
Keyless Control (Bank 2) See page 15 for Programming Instrucon.
Features
Feature Bank 2
1 Lock / Unlock Funcon 2 Accessory Lock 3 Accessory Unlock 4 Exterior
Illuminaon 5 Auto Relock 6 Auto Arming 7 Noficaon Sound 8 Horn Timing 9 Valet
Override Method 10 Driver Priority Unlock 11 Silent Choice 12 Park Light /
Trunk Swap 13 AUX Ch. 4 14 AUX Ch. 5 15 AUX Ch. 6 16 AUX Ch. 7 17 Security
Profile 18 Data Port Protocol
1 Chirp
500ms NA NA NA NA NA NA 16ms NA NA OFF NA NA NA NA NA OFF ADS
2 Chirp
3.5s ec
3 Chirp
500ms L, DBL UL
Opons 4 Chirp
DBL L, 500ms UL
30ms From Transmier
40ms OEM Style
50ms
OEM Security DBI
W/ OEM Remote Start
5 Chirp
DBL L, DBL UL
6 Chirp
500ms L, 350ms UL
10ms
Feature 1: Lock / Unlock Function Funcon: Set the lock / unlock output timing
and functionality for specific vehicle lock types. Setting Choices:
· Option 1 – Lock and Unlock outputs will pulse for 500 milliseconds. · Option
2 – Lock and Unlock outputs will pulse for 3.5 seconds. · Option 3 – Lock
output will pulse for 500ms ; Unlock output will pulse twice, 500ms each. ·
Option 4 – Lock output will pulse twice, 500ms each ; Unlock output will pulse
for 500ms. · Option 5 – Lock and Unlock outputs will pulse twice for 500ms. ·
Option 6 – Lock output will pulse for 500ms ; Unlock output will pulse for
350ms.
Feature 2: Accessory-Activated Lock This Feature is not available on this
model.
Feature 3: Accessory-Activated Unlock This Feature is not available on this
model.
Feature 4: Exterior Illumination This Feature is not available on this model.
Feature 5: Auto ReLock Setting This Feature is not available on this model.
Feature 6: Automatic Arming This feature is not available on this model.
Feature 7: Notification Sounds This feature is not available on this model.
8
APS57TM_RevA_07/20
Detailed Descriptions: Setup Opons
Keyless Control (Bank 2) (cont.) See page 15 for Programming Instrucon.
Feature 8: Horn Output Duration Funcon: Set the horn output to activate for a
set time. Setting Choices:
· Option 1 – Output pulses for 16 milliseconds. · Option 2 – Output pulses for
30 milliseconds. · Option 3 – Output pulses for 40 milliseconds. · Option 4 –
Output pulses for 50 milliseconds. · Option 5 – Output pulses for 10
milliseconds.
Feature 9: Override Method This feature is not available on this model.
Feature 10: Driver Priority Unlock This Feature is not available on this
model.
Feature 11: Silent ChoiceTM Funcon: Set audible beeps on or off when arming
and disarming the system. Setting Choices:
· Option 1 – Pressing Lock or Unlock at any me will perform the funcon with
audible beeps. · Option 2 – Pressing Lock or Unlock for 1.5sec on remote will
control system without an audible beep. · Option 3 – First press of Lock or
Unlock on the remote control will perform the funcon without an audible
sound. Second press within 10sec will result in audible beeps.
Feature 12: Park Light / Trunk Relay Function This Feature is not available on
this model.
Feature 13 – 19: AUX Ch. 4 Output This Feature is not available on this model.
Feature 14 – 19: AUX Ch. 5 Output This Feature is not available on this model.
Feature 15 – 19: AUX Ch. 6 Output This Feature is not available on this model.
Feature 16 – 19: AUX Ch. 7 Output This Feature is not available on this model.
Feature 17: Security Profile Funcon: Set the system to function as a keyless
entry / convenience system or full-featured alarm / convenience system.
Setting Choices:
· Option 1 – OFF, no security protecon. · Option 2 – OEM Security, entry zone
protecon. · Option 3 – w/ OEM Remote Start, entry zone protecon with OEM
remote start compability.
Feature 18: Data Bus (DBI) Port Protocol
Funcon: Set functionality of the data bus connector to accept integration modules of differing protocols.
Setting Choices:
· Option 1 – The data bus connector will be configured to work with modules that use the ADS Protocol.
· Option 2 – The data bus connector will be configured to work with modules that use the DBI Protocol.
APS57TM_RevA_07/20
9
Detailed Descriptions: Setup Opons
Remote Start Control (Bank 3) See page 15 for Programming Instrucon.
Features
Feature Bank 3
1 Defrost Output 2 RS Start Noficaon 3 RS Runme 4 RS Parking Lights 5 Engine
Confirmaon 6 Voltage Level 7 Ignion 2 Output 8 Ignion 3 Output 9 Accessory
Output 10 Transmission 11 Max Crank Time 12 Diesel Delay 13 Temperature Start
14 Crank Duraon 15 RS Shock Override 16 Turbo Timer 17 Start Acvaon 18 RS Lock
Funcon 19 Factory Disarm Output 20 Pulse During Crank 21 Factory Arm Output 22
Pulse Aer Shutdown 23 Addional Unlock Pulse
1 Chirp
NA ON 15min Steady Tach >0.5v B4 Start Ignition N/A Accessory NA 0.8sec OFF NA
Averaging NA NA Two Press No Change Single Pulse During Crank After Start
After Shutdown No Pulse
2 Chirp
OFF 20mi n Fl a s hi ng Vol ta ge <0.5v B4 Start Ac c es s ory
I gni on
1.0s ec Diesel 5
Pr es et
One Press UL Before L Aer
350ms GWR GWR GWR IGN, ACC, GWR
3 Chirp
Opons 4 chirp
45mi n Data Start Start 1.5s ec Diesel 10
60mi n Hybri d
2.0s ec Diesel 15
Three Press UL Before Start
500ms I gni on I gni on I gni on IGN,ACC,GWR,PASD
Lock Aer Start 800ms
Ac c es s ory Ac c es s ory Ac c es s ory
5 Chirp
5mi n
3.0s ec Diesel 20
Same As Bank 2, F1 Start Start
Feature 1: Defrost Output Duration This Feature is not available on this
model.
Feature 2: Remote Start Notification Funcon: Set remote start activation
confirmation beeps on or off. Setting Choices:
· Option 1 – On – System emits an audible beep when remote start is acvated. ·
Option 2 – OFF -System remains silent when remote start is acvated.
Feature 3: Remote Start Run Time Funcon: Set the maximum remote start run time
if the vehicle is not entered after activation. Setting Choices:
· Option 1 – Engine will run for 15 minutes. · Option 2 – Engine will run for
20 minutes. · Option 3 – Engine will run for 45 minutes. · Option 4 – Engine
will run for 60 minutes. · Option 5 – Engine will run for 5 minutes. · Option
6 – Engine will run for 10 minutes.
Feature 4: Remote Start Parking Light Duration Funcon: Set parking light
output to turn on or flash lights during remote start. Setting Choices:
· Option 1 – Lights remain on during remote start. · Option 2 – Lights flash
during remote start.
6 Chirp
10mi n
4.0s ec Diesel 30
10
APS57TM_RevA_07/20
Detailed Descriptions: Setup Opons
Remote Start Control (Bank 3) (cont.) See page 15 for Programming Instrucon.
Feature 5: Engine Confirmation Funcon: Determine how the system knows if
remote start was successful. Setting Choices:
· Option 1 – Determined by measurement from the Purple/White Tach Input wire.
· Option 2 – Determined by the voltage difference before remote start and aer
as set in Bank 3, Feature 6. · Option 3 – Receives informaon through an aached
data bus interface. · Option 4 – No sensing; assumes vehicle has started based
on setting in Bank 3, Features 11 & 14.
Feature 6: Start Sensing Voltage Level Funcon: Set the sensitivity of voltage
variance measurement to determine if the vehicle has started when Feature 5 is
set to option 2, Voltage. Setting Choices:
· Option 1 – High: Voltage difference before remote start and aer must be
greater than .5 volts. · Option 2 – Low: Voltage difference before remote
start and aer must be less than .5 volts.
Feature 7: Ignition 2 Output Function (Green) Funcon: Set the functionality of
the programmable Ignition 2 output. Setting Choices:
· Option 1 – Wire sends 12-Volt (+) during ignion and start. · Option 2 – Wire
sends 12-Volt (+) during ignion; drops out during start. · Option 3 – Wire
sends 12-Volt (+) during start only.
Feature 8: Ignition 3 Output Function (Pink) This Feature is not available on
this model.
Feature 9: Accessory Output Function (Purple) Funcon: Set the functionality of
the programmable Accessory output. Setting Choices:
· Option 1 – Wire sends 12-Volt (+) during ignion; drops out during start. ·
Option 2 – Wire sends 12-Volt (+) during ignion and start. · Option 3 – Wire
sends 12-Volt (+) during start only.
Feature 10: Transmission Type This Feature is not available on this model.
Feature 11: Maximum Crank Time Funcon: Set maximum crank time for all remote
start settings. Setting Choices:
· Option 1 – Starter will crank for .8 seconds. · Option 2 – Starter will
crank for 1 second. · Option 3 – Starter will crank for 1.5 seconds. · Option
4 – Starter will crank for 2 seconds. · Option 5 – Starter will crank for 4
seconds.
APS57TM_RevA_07/20
11
Detailed Descriptions: Setup Opons
Remote Start Control (Bank 3) (cont.) See page 15 for Programming Instrucon.
Feature 12: Diesel (Pre-Start) Delay Funcon: After remote start ignition is
activated, set delay of crank to accommodate diesel engines. Setting Choices:
· Option 1 – Vehicle starts immediately aer remote start ignion. · Option 2 –
Start is delayed for 5 seconds aer remote start ignion. · Option 3 – Start is
delayed for 10 seconds aer remote start ignion. · Option 4 – Start is delayed
for 15 seconds aer remote start ignion. · Option 5 – Start is delayed for 20
seconds aer remote start ignion. · Option 6 – Start is delayed for 45 seconds
aer remote start ignion.
Feature 13: Temperature-Based Start Setting This Feature is not available on
this model.
Feature 14: Crank Duration Funcon: Set how the system will determine how long
to crank the starter. Setting Choices:
· Option 1 – Starter will crank based on average of last 8 times the vehicle
was started with the key. · Option 2 – Starter will crank for maximum time as
set in Bank 3, Feature 11.
Feature 15: Shock Sensor Control This feature is not available on this model.
Feature 16: Turbo Timer Setting This Feature is not available on this model.
Feature 17: Remote Start Activation Funcon: Set remote start to activate with
one, two, or three presses from the remote control or pulses detected on the
Dark Blue/Black External Activation Input. Setting Choices:
· Option 1 – Press the Start buon 2 times for remote start. · Option 2 – Press
the Start buon 1 time for remote start. · Option 2 – Press the Start buon 3
times for remote start.
Feature 18: Remote Start Lock Control Funcon: If desired, set door lock
outputs to function before or after remote start. Setting Choices:
· Option 1 – Remote Start Lock Control is inactive. · Option 2 – Doors will
unlock before remote start; lock after remote start. · Option 3 – Doors will
unlock before remote start. · Option 4 – Doors will lock after remote start.
Feature 19: Factory Disarm Output Function (BLACK/BLUE) Funcon: Set the
functionality of the programmable output. Setting Choices:
· Option 1 – Sends a 1-second pulse before start and during Unlock. · Option 2
– Sends a 350ms pulse before start and during Unlock. · Option 3 – Sends a
500ms pulse before start and during Unlock. · Option 4 – Sends a 800ms pulse
before start and during Unlock. · Option 5 – Sends a pulse before start and
during unlock based on setting of Bank 2, Feature 1.
12
APS57TM_RevA_07/20
Detailed Descriptions: Setup Opons
Remote Start Control (Bank 3) (Cont.) See page 15 for Programming Instrucon.
Feature 20: Pulse During Crank Output Function (BLACK/YELLOW) Funcon: Set the
functionality of the programmable output. Setting Choices:
· Option 1 – Pulse During Crank. · Option 2 – GWR, Remote Start Status Output.
· Option 3 – Ignion Timing. · Option 4 – Accessory Timing.
Feature 21: Factory Arm Output Function (BLACK/LIGHT GREEN) Funcon: Set the
functionality of the programmable output. Setting Choices:
· Option 1 – Pulse Aer Start Output. · Option 2 – GWR, Remote Start Status
Output. · Option 3 – Ignition Output. · Option 4 – Accessory Output. · Option
5 – Start Output.
Feature 22: Pulse After Shutdown Output Function (BLACK/RED) Funcon: Set the
functionality of the programmable output. Setting Choices:
· Option 1 – Pulse Aer Shutdown Output. · Option 2 – GWR, Remote Start Status
Output. · Option 3 – Ignition Output. · Option 4 – Accessory Output. · Option
5 – Start Output.
Feature 23: Additional Unlock Pulses Funcon: Set other outputs to pulse when
the vehicle is unlocked with the remote control. Setting Choices:
· Option 1 – No addional unlock pulses. · Option 2 – Pulse Ignition, Accessory
and Ground While Running wires upon Unlock. · Option 3 – Pulse Ignition,
Accessory, Ground While Running, and Pulse After Shutdown wires upon unlock.
APS57TM_RevA_07/20
13
Detailed Descriptions: System Operaon
Remote Control Operation
This system includes two (2) remote controls. The matrix below describes the
basic funcons of each remote. See Owners Guide for complete remote operaon
matrix.
Three Buon Remotes (1-Way)
Button
Action
Press 1x Hold 3 Seconds Press 1x Hold 3 Seconds Press 2x Hold 3 Seconds
Function
Lock Panic ON/OFF Unlock Panic ON/OFF Start (Programable) Trunk Release
14
APS57TM_RevA_07/20
Quick Reference: System Programming
Programming Mode Entry and Exit Procedure
Once the system is installed and powered up, you will use the vehicle ignion,
override buon and a programmed remote control to set all system opons. Feature
opons are divided into categories, or Banks, as described throughout this
secon. Ensure that at least one remote control is programmed to the system. If
not, or if you need to program more remote controls, use the diagram steps to
access Bank 1. The siren and LED will indicate your status and selecons.
Follow the diagram below to enter and maneuver through the programming
procedure.
LOCK A
CC ON Ignition On
START
3X
1X
CC ON
START
2 = Bank 2 3 = Bank 3
LOCK A
Press and Release Override Button
1 Chirp = Bank 1 (Program Remotes)
CC ON
… or Exit Programming
Cycle Key to Advance Banks (2,3)
Chirps Indicate Bank Number
Press Override Button to Advance Within Bank
LED Indicates Feature Selection
Repeat Steps to Program Another Feature Bank…
Repeat Steps to Program Another Feature …
Press to Change Feature Option
LOCK A
START
Ignition Off
Note: Programming will time out after 60sec with no activity or Ignition Off for 5sec.
Chirps Indicate Option Number
1. Turn the ignion ON. 2. Press and release the valet buon three (3) mes. 3.
The system will beep (1) one me, indicang you have accessed Bank 1. 4. Each
cycle of the Ignion, OFF/ON, will advance to the next bank (up to Bank 3) then
restart at Bank 2. (Note: To re-
access Bank 1 for transmier programming, you will need to exit and re-enter
programming mode.) 5. The system will beep a number of mes to indicate the
Bank number:
· 1 beeps: Bank 1 – Programming Remote Controls · 2 beeps: Bank 2 – Keyless
Control Options · 3 beeps: Bank 3 – Remote Start Control Options
6. Once you have accessed the desired bank, press the valet buon to advance
though the features. The LED will flash a number of mes to indicate the
feature, based on the charts that follow this secon. The system will chip a
number of mes to indicate the Opon programmed.
7. Once you have accessed the desired feature, press the LOCK buon on the
remote control to advance though the feature’s setting opons. The system will
beep a number of mes to indicate the Opon setting, based on the charts that
follow this secon.
8. Once you have made the desired setting, you can press the valet buon to
advance through the features within the bank, or cycle the Ignion key OFF/ON
to advance to the next bank.
9. Once you have completed programming, you MUST turn the ignition key to OFF
to exit the programming mode. Programming will automacally exit aer 60 seconds
of inacvity.
APS57TM_RevA_07/20
15
Quick Reference: System Programming
Bank 1: Transmitter Programming Options See page 7 for a detailed descripon.
Feature Bank 1
1 Auto Program/Lock 2 Unlock 3 Trunk/Start
Descripon
Press Lock buon on remote Press Unlock buon on remote Press Start buon on
remote
Features CH.
Bank 2: Keyless Options See pages 8-9 for detailed descripons.
Feature Bank 2
1 Lock / Unlock Funcon 2 Accessory Lock 3 Accessory Unlock 4 Exterior
Illuminaon 5 Auto Relock 6 Auto Arming 7 Noficaon Sound 8 Horn Timing 9 Valet
Override Method 10 Driver Priority Unlock 11 Silent Choice 12 Park Light /
Trunk Swap 13 AUX Ch. 4 14 AUX Ch. 5 15 AUX Ch. 6 16 AUX Ch. 7 17 Security
Profile 18 Data Port Protocol
1 Chirp
500ms NA NA NA NA NA NA 16ms NA NA OFF NA NA NA NA NA OFF ADS
2 Chirp
3.5s ec
3 Chirp
500ms L, DBL UL
Opons 4 Chirp
DBL L, 500ms UL
30ms From Transmier
40ms OEM Style
50ms
OEM Security DBI
W/ OEM Remote Start
5 Chirp
DBL L, DBL UL
10ms
Bank 3: Remote Start Options See pages 10-13 for detailed descripons.
6 Chirp
500ms L, 350ms UL
Features
Feature Bank 3
1 Defrost Output 2 RS Start Noficaon 3 RS Runme 4 RS Parking Lights 5 Engine
Confirmaon 6 Voltage Level 7 Ignion 2 Output 8 Ignion 3 Output 9 Accessory
Output 10 Transmission 11 Max Crank Time 12 Diesel Delay 13 Temperature Start
14 Crank Duraon 15 RS Shock Override 16 Turbo Timer 17 Start Acvaon 18 RS Lock
Funcon 19 Factory Disarm Output 20 Pulse During Crank 21 Factory Arm Output 22
Pulse Aer Shutdown 23 Addional Unlock Pulse
16
1 Chirp
NA ON 15min Steady Tach >0.5v B4 Start Ignition N/A Accessory NA 0.8sec OFF NA
Averaging NA NA Two Press No Change Single Pulse During Crank After Start
After Shutdown No Pulse
2 Chirp
OFF 20mi n Fl a s hi ng Vol ta ge <0.5v B4 Start Ac c es s ory
I gni on
1.0s ec Diesel 5
Pres et
One Press UL Before L Aer
350ms GWR GWR GWR IGN, ACC, GWR
3 Chirp
Opons 4 chirp
45mi n Data Start Start 1.5s ec Diesel 10
60mi n Hybri d
2.0s ec Diesel 15
Three Press UL Before Start
500ms I gni on I gni on I gni on IGN,ACC,GWR,PASD
Lock Aer Start 800ms
Ac c es s ory Ac c es s ory Ac c es s ory
5 Chirp
5mi n
6 Chirp
10mi n
3.0s ec Diesel 20
4.0s ec Diesel 30
Same As Bank 2, F1 Start Start
APS57TM_RevA_07/20
Quick Reference: System Programming & Diagnoscs
Data Port Protocol Selection
The default data port protocol of this model is ADS (iDatalink 2-Way). This
model is capable of detecng the correct data port protocol (ADS or DBI) and
automacally configuring Feature Bank 2; Feature 18. To inialize the detecon
procedure: 1. Press and hold the valet buon. 2. Cycle the vehicle’s Ignion
ON/OFF two (2) mes. 3. Release the valet buon. Note: This feature is only
available on module firmware v2.00 or higher.
Tach Function
When using the GREEN/ORANGE tach wire, the vehicle tach rate must be
programmed.
Programming with valet button when tach wire is connected: 1. Turn the ignion
key to the ON posion. 2. Press and release the valet buon three (3) mes. 3.
Immediately turn the ignion key OFF. 4. Press and hold the valet buon, then
start the vehicle using the key. 5. When the unit senses the tach signal, the
parking lights will begin to flash. 6. Allow the vehicle to sele to a normal
idle speed. 7. Release the valet buon.
The parking lights will turn on for two (2) seconds and one (1) long chip will
indicate that the learned tach signal is stored and the unit has exited tach
learn mode.
Programming without valet button when tach wire is connected: 1. Turn the
ignion key to the ON posion and start the vehicle’s engine. 2. Wait for Engine
RPM to lower to a normal idle. 3. Press and hold the vehicle’s brake pedal. 4.
Press the LOCK buon on the OEM remote or the Carlink App.
The vehicle’s parking lights will flash seven (7) mes to indicate the tach
signal has been learned. If the parking lights do not flash, locate another
tach source and repeat steps 1 – 4 above.
Note: Programming tach signal via OEM or Telemacs control is only available on
Firmware v1.47 or Higher.
Valet Alarm Override (Optional)
The Valet Override procedure will disable the alarm when the remote is not
available or has become inoperave. If the vehicle door is opened without
disarming, the alarm will sound and the vehicle will not start when aempng to
start with the key. To disable the alarm:
1. Turn the vehicle ignion to ON. 2. Within 5sec, press and release valet
buon one (1) me.
The alarm will silence and the vehicle will now start normally with the key.
APS57TM_RevA_07/20
17
Quick Reference: System Programming & Diagnoscs
Silent Lock and Unlock
Program the Presge system to Lock and Unlock without noficaon beeps. 1. Turn
the ignion ON then OFF. 2. Press and release the valet buon three (3) mes. The
system will respond with one (1) beep for ON or two (2) beeps for OFF.
User Selectable LED
This feature will control whether the LED is ON or OFF when the system is
Armed/Locked. This will be selectable in feature programming OR on-the-fly
without entering the programming feature banks. 1. Turn the ignion ON, OFF,
ON, OFF. 2. Press and hold valet buon for five (5) seconds. The LED will flash
one (1) me for ON, two (2) mes for OFF. This feature will not affect LED flash
during programming.
Troubleshooting Remote Start
All Presge remote start system will provide parking light feedback to display
remote start errors or shutdowns. The vehicle parking lights will flash to
display error or shutdown code.
1 Runme Expired 2 Remote Shutdown 3 Brake On 4 Manual Mode 5 Hood Open 6 Low /
No Tach 7 Tach Programming 8 High Tach
18
APS57TM_RevA_07/20
Quick Reference: Wiring Diagrams
Door Lock Connections
Negative-Trigger Door Locks Verification: The vehicle wires register Ground
when the Lock and Unlock switches are acvated.
RED ( – ) Lock Output
Lock Unlock
Vehicle Door Lock Control Relays
GREEN ( – ) Unlock Output
Positive-Trigger Door Locks Verification: The vehicle wires register 12V+ when the Lock and Unlock switches are acvated.
87
87a
86
85
30
Fused +12 Volt Battery Souce
RED ( – ) Lock Output
Lock Unlock
Vehicle Door Lock Control Relays
87
87a
86
85
30
Fused +12 Volt Battery Souce
GREEN ( – ) Unlock Output
APS57TM_RevA_07/20
19
Quick Reference: Wiring Diagrams
Door Lock Connections
Single-Wire Negative Multiplex Door Locks (Relays required) Verification: The
vehicle wire registers variable Ground values when the Lock and Unlock
switches are acvated. Please consult the vehicle-specific wire and locaon
chart for resistor values.
RED ( – ) Lock Output
87
87a
86
85
30
Lock
Unlock
Ground
Fused +12 Volt Battery Source
Resistor
87
87a
86
85
30
Green ( – ) Unlock Output
Vehicle Door Lock Control Relays
Single-Wire Positive Multiplex Door Locks (Relays required) Verification: The
vehicle wire registers variable 12V+ values when the Lock and Unlock switches
are acvated. Please
consult the vehicle-specific wire and locaon chart for resistor values.
RED ( – ) Lock Output
87
87a
86
85
30
Lock
Unlock
Fused +12 Volt Battery Source
Resistor
87
87a
86
85
30
Green ( – ) Unlock Output
Vehicle Door Lock Control Relays
20
APS57TM_RevA_07/20
Quick Reference: Wiring Diagrams
Door Lock Connections
Reverse-Polarity Door Locks (Relays required) Verification: The vehicle wires
rest at Ground and register 12V+ when the Lock and Unlock switches are
acvated.
Lock Unlock
87
87a
86
85
30
X
Cut
87
87a
86
85
30
X
Cut
Fused +12 Volt Battery Souce
RED ( – ) Lock Output
To Door Lock Motor Fused +12 Volt Battery Souce
Green ( – ) Unlock Output
To Door Lock Motor
Aftermarket Actuators (Relays and door lock actuators required)
Door Lock Actuator
M
87
87a
86 30
Fused +12 Volt Batter y Source
85
Chassis Ground
RED ( – ) Lock Output
APS57TM_RevA_07/20
87
87a
86 30
Fused +12 Volt Batter y Source
85
Chassis Ground
GREEN ( – ) Unlock Output
21
APS57TM_RevA_07/20
22
6 Pin RS Harness
1 Yellow 2 Green 3 Red 4 Red/White 5 Purple 6 Blue Replacement Part #4120467
135 246
Starter Output (+) Ignion 2 Output (+) P Baery 12V Input (+) Baery 12V Input
(+) Accessory Output (+) P Ignion Input / Output (+)
13 24
4 Pin Light
1 White 2 White/Red 3 Yellow/Black 4 Black Replacement Part #4120463
Parking Light (30) Output P Parking Light (87) Input Ignition Output For Alarm (+) Ground Input (-)
Weblink
4 Red
3 Black
2 White 1 Blue Accessory Sold Seperatly
1234
Battery 12V (+) Ground (-) Data RX Data TX
Antenna
4180070
183BP
183BP
VOXX
FLCART Dock
Replacement Part #4361009
1 Pink 2 Green 3 Black 4 Red 5 Blue
123456
Baery 5V (+) Data RX Ground (-) Valet Switch LED (-)
13 14 11 12 9 10 78 56 34 12
1 2 3 4
4 3 2 1
CarLink
DBI
14 Pin Main Input/Output
14 Green/Orange 13 Black/Yellow 12 Green/Yellow 11 Black/Red 10 Dk. Blue 9 Black/Blue 8 Brown/Black 7 Black/Lt. Green 6 Dk. Blue/Black 5 Lt. Blue 4 Green 3 Gray/Black 2 Red 1 Black/White
Tach Input Pulse During Crank Output (-) Glow Plug Input (+) Pulse Aer
Shutdown Output (-) Trunk Output (-) Factory Disarm Output (-) Brake Input (+)
Factory Arm Output (-) External Acvaon Input (-) Remote Start Status Output
(-) Unlock Output (-) Hood Input (-) Lock Output (-) Horn Output (-)
Replacement Part #4120476
4 Red 3 Blue 2 Black 1 White
Baery 12V (+) Data TX Ground (-) Data RX
Accessory Sold Seperatly
4 Red 3 Blue 2 Black 1 White
Baery 12V (+) Data TX Ground (-) Data RX
Accessory Sold Seperatly
19 20 17 18 15 16 13 14 11 12 9 10 78 56 34 12
This Harness is included with the FLCART. For Wire Informaon and Diagram
Please Refer to Vehicle Specific
FlashLogic Install Guide. Visit www.FlashLogic.com for More Informaon.
Quick Reference: Wiring Diagrams
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>