VOXX ELectronics R6867T Digital Control Center Instruction Manual
- June 4, 2024
- VOXX ELectronics
Table of Contents
R6867T Replacement Digital Control Center
Instruction Manual
Product Description
The R6867T control center is compatible with the following modules:
DS4 and DS4+.
Mounting the Control Center
Note Once this replacement control center has been installed, all remote
controls must be paired with your system. See Remote Pairing for details and
follow the instructions for your remote control type.
The control center’s position should be discussed with the vehicle owner prior
to installation since the antenna, with built-in status LED and Valet/
Program, must be visible/accessible to the customer.
The best position to locate the control center is centered high on the front
windshield. It can be mounted vertically or horizontally relative to the
windshield. Metallic window tint can also affect range negatively, so this
should be a consideration when determining the mounting location.
After you determine the best mounting location, follow these steps:
Clean the mounting area with a quality glass cleaner or alcohol to remove any
dirt or residue.
Plug the cable into the control center.
Mount the control center with double-sided tape.
Route the cable down the window pillar to the control module and plug the
cable in the control module.
Remote Pairing
Prepare the vehicle system to be Paired with a new remote
- Open at least one vehicle door.
- Turn the key to the ON position.
- Within 5 seconds press and release the Control button on the Control Center one time.
- Within 5 seconds, press and hold the Control button on the Control Center. The status LED begins flashing in a single flash sequence and the siren/horn sounds once to confirm the system is ready for remote pairing. Release the button.
- Locate your remote control model below and follow the instructions.
System Pairing will exit if:
- The ignition is turned off
- The open door is closed
- 60 seconds lapse with no actions
Note: Make sure the remote to be paired with the system is set for the
desired Car 1 or Car 2 operation.
LCD Remote Control:
- Press and hold the button for 8 seconds, the remote beeps once, Main Menu is displayed. Release the button.
- Press the AUX or buttons until Pair is displayed.
- Press and hold the button until the remote beeps 3 times then release the button. The remote is now ready to pair with the system.
- Press the button.
- Wait several seconds for feedback as the remote generates security encryption and sends it to the Control Center. If pairing is successful the siren/horn sounds and the remote emits several tones. The screen displays if the Pairing is successful or failed with the corresponding text. If pairing fails repeat step 4.
To exit pairing mode on the remote:
- Press and release the button.
- Wait 30 seconds without pressing a command button on the remote.
Responder LED or Companion Remote Control:
- Press and hold the button for 8 seconds. The transmit LED will come to on solid. Release the button.
- Press and hold the until the transmit LED flashes 3 times then comes on solid.
- Press the button.
- Wait several seconds for feedback as the remote generates security encryption and sends it to the Control Center. If pairing is successful the siren/horn sounds and the 2-way remote emits several tones (the companion remote does not generate tones). If pairing is not successful Press and release the button once and then repeat steps 2 and 3.
To exit pairing mode on the remote:
- Press and release the button once, then press and hold until the transmit LED shuts o.
- Wait 30 seconds without pressing a command button on the remote control.
GOVERNMENT REGULATIONS
This device complies with Part 15 of FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including
interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television, which can be determined by turning the equipment OFF and
ON, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
To satisfy FCC RF exposure compliance requirements, the device and its antenna
must maintain a separation distance of 20 cm or more from the person’s body.
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Health Canada RF Exposure Warning:
This device complies with Health Canada’s Safety Code. The installer of this
device should ensure that RF radiation is not emitted in excess of the Heath
Canada’s requirement. The device must maintain a separation distance of 20cm
or more from the person’s body. Information can be obtained at:
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct
/index-eng.php
LIMITED ONE YEAR CONSUMER WARRANTY
For a period of ONE YEAR from the date of purchase of a Directed Electronics
remote start or security product, Directed Electronics. (“DIRECTED”) prom
-ises to the original purchaser, to repair or replace with a comparable
reconditioned piece, the security or remote start accessory piece (hereinafter
the “Part”), which proves to be defective in workmanship or material under
normal use, provided the following conditions are met: the Part was purchased
from an authorized DIRECTED dealer; and the Part is returned to DIRECTED,
postage prepaid, along with a clear, legible copy of the receipt or bill of
sale bearing the following information: consumer’s name, address, telephone
number, the authorized licensed dealer’s name and complete product and Part
description.
This warranty is nontransferable and is automatically void if the Part has
been modified or used in a manner contrary to its intended purpose or the Part
has been damaged by accident, unreasonable use, neglect, improper service,
installation or other causes not arising out of defect in materials or
construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE,
ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED
WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND
WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL ROPERTY, ARE EXPRESSLY EXCLUDED;
AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR
IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED
HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD
PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE
OR INSURANCE GAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS
OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING
WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF
A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE
SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS
AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM
RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE
AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL
NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO,
ANY CONSEQUENTIAL DAMAGES, INCIDENTAL
DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS
OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE
MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S
OPTION
THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and
Canada. Parts sold outside of the United States of America or Canada are sold
“AS-IS” and shall have NO WARRANTY, express or implied. Some states do not
allow limitations on how long an implied warranty will last or the exclusion
or limitation of incidental or consequential damages. This warranty gives you
specific legal rights and you may also have other rights that vary from State
to State. DIRECTED does not and has not authorized any person or entity to
create for it any other obligation, promise, duty or obligation in connection
with this Part. For further details relating to warranty information of
Directed products, please visit the support section of DIRECTED’s website at:
www.directed.com
© 2022 VoxxElectronics, All rights reserved.
NR6867T–2022-07-11
Documents / Resources
| VOXX
ELectronics R6867T Digital Control
Center
[pdf] Instruction Manual
R6867T, EZSR6867T, Digital Control Center, R6867T Digital Control Center,
R6867T Replacement Digital Control Center, Replacement Digital Control Center,
Control Center
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>