Voxx Accessories SUVC300 Stereo Alarm Clock with UVC Sanitizer User Guide

June 6, 2024
Voxx Accessories

Stereo Alarm Clock
with UVC Sanitizer

Quick Start Guide

Plug in

Plug the included power cable into the DC 5V jack on the back of the clock/sanitizer.
Plug the other end into a power outlet or surge protector.

Battery Backup

Your clock has a pre-installed battery backup that will keep the time in case power is interrupted (like by a power outage, for example). To start using the battery backup, pull the activation tab above the battery door inside the battery compartment. The protective film covering the battery will come off with the tab and the battery will be activated.
If you notice that the battery backup is no longer working, simply replace the CR2032 coin-cell battery in the battery compartment. Use a coin to turn the battery door and unlock it. Then remove the door and access the CR2032 battery.

Set the time

Press and hold the button on the top of the clock/sanitizer until the hour’s digits flash.
Use the VOL/SET + and — buttons on the top of the clock/sanitizer to adjust the hour. Press to set.
Use the VOL/SET + and — buttons to adjust the minutes. Press to set.
Use the + and — buttons to choose 12- (AM/PM) or 24-hour time. (12-hour time is the default.) Press to finish setting the time.

Load up the sanitizer

Open the cover of the clock/sanitizer. Then place the item you want to sanitize inside.

Voxx Accessories SUVC300 Stereo Alarm Clock with UVC Sanitizer -
sanitizer

Note: The mirror on the inside of the cover comes from the factory with a scratch-resistant removable film. Pull the tab on the film’s corner and gently remove it before you start sanitizing.

Charge up, too!
The clock/sanitizer can charge your mobile device too! Just plug your charging cable (not included) into the charging port inside the clock/sanitizer.

Sanitize!

Close the cover and choose the sanitization cycle you want to use.

For these items Use this cycle To start:
Hard, non-porous (like phones, tablets, watches, and remote controls)
Standard cycle (around 10 minutes) Press the button.
Fabric and soft porous (like facemasks, toothbrushes, and makeup brushes)
Deep clean cycle (around 20 minutes) Press and hold the button until the

indicator on the clock display flashes twice.

The indicator on the clock display turns on during sanitization. It turns off when the sanitization cycle is complete.
To stop sanitization before the cycle is complete:
Press the button. The indicator on the clock displays flashes three times to indicate the cycle has stopped and it’s safe to open the cover.

Notes:

  • The indicator flashes if the cover is open when you try to start sanitization. For your safety, the sanitizer cannot proceed with sanitization if the cover is open. Make sure the cover is completely closed, then press the button again.
  • You can use the deep clean cycle even for items that don’t need it. There’s no harm done to the item—it just takes longer to finish the cycle.

Get your clean stuff

Open the cover of the clock/sanitizer. Remove the item you placed inside — it’s safe to use now!

Set up Bluetooth

Press the FM/ button on the top of the clock/sanitizer twice (or until the indicator on the clock display flashes).
Choose Surface SUVC300 from the list of available Bluetooth devices on your phone.
The indicator on the display goes solid when your phone is connected. You can start streaming music from your phone to the stereo clock’s speakers now!
To pair to a new device: Make sure the
indicator on the clock display is on. Then press and hold the FM/ ****button for 3 to 4 seconds to go into pairing mode.

Everyday Use

Setting the alarms

To set the time for alarm 1 ( ):

  1. Press and hold the button on the top of the clock/ sanitizer until the hour’s digits flash on the display.
  2. Use the + and — buttons on the top of the clock/sanitizer to adjust the hour. Press to set.
  3. Use the + and — buttons to adjust the minutes. Press to set.
  4. Use the + and — buttons to set the alarm sound: buzzer (bu), radio (rd), or Bluetooth (bt). Press to set.

To set the time for alarm 2 ( ): Follow the steps above, using the button instead of **.
To turn an alarm on/off: Press the button for the alarm you want to turn on or off ( or ** ). The alarm time appears on the display and the indicator on the display shows that you’ve turned that alarm on or off. The display returns to the current time after 10 seconds.

Using the nightlight

To turn on and adjust the nightlight: Press the button on the top of the clock sanitizer. Each press goes to the next brightness setting: high, medium, low, and off.

Listening to FM Radio and Bluetooth

To listen to FM Radio: Press the FM/ button until the FM indicator appears on the clock display.
To scan for FM stations: Press and hold the TUNE + or – button. A single press of either button will fine tune the frequency up or down.
To set preset FM stations: In radio mode, use the TUNE + and – buttons to find the FM station you want as a preset. Press and hold the button to set this station as a preset. The preset number (P01, P02, etc.) appears on the display. Press again to confirm. There are 19 available radio presets.
To tune to an FM preset station : In radio mode, press the button repeatedly to cycle through the 19 preset stations.
To listen to Bluetooth audio: Press the FM/ button until the indicator appears on the clock display. Then start playing music on your Bluetooth device.
To adjust the volume: Press the VOL/SET + and — buttons on the top of the clock/sanitizer. You can also use the volume controls on your phone for Bluetooth audio.

Tour of the Stereo Alarm Clock with UVC Sanitizer

DISPLAY
AM and PM indicators show if the time displayed is AM or PM in 12hour time format.
indicator turns on during sanitization and turns off when the sanitization cycle is complete. This indicator flashes continuously if the cover is open when you try to start sanitization.
indicator flashes when pairing with a new device. It turns solid when connected.
and indicators show if alarm 1 and/or alarm 2 are active.
indicator turns on when the backup battery needs to be replaced.
See step 1 for details.
FM indicator turns on in radio mode.

TOP AND SANITIZE TION BAY
TUNE + and – buttons scan for FM stations (press and hold) or fine tune the FM radio frequency (press).
button turns on the built-in nightlight and goes to the next brightness setting (high, medium, low, and off).
VOL/SET + and – buttons adjust the flashing digits when setting the time or alarm. They also adjust the volume when listening to FM radio or Bluetooth audio.
SNOOZE/bar temporarily delays the alarm another 9 minutes until you turn it off. In Bluetooth audio mode, this bar plays or pauses playback. It also adjusts the display brightness in other modes.
and buttons let you set the alarm times (press and hold) or turn each alarm on/off (press).
button starts the sanitization process once the top is closed. You can choose the standard cycle (press) or deep clean cycle (press and hold). Press this button during a sanitization cycle to stop the cycle before it’s complete. The indicator flashes three times to indicate the cycle has stopped and it’s safe to open the cover.
button lets you set the time (press and hold) or display the current time (press). In radio mode, this button goes to your next preset station (press) or sets the current station as a preset (press and hold).
FM/ button toggles between FM radio (one press), Bluetooth audio (two presses), and audio off (three presses). It also starts Bluetooth pairing (press and hold) in Bluetooth mode.
The sanitization bay is where you put the item you want to sanitize.
Once you’ve closed the top and pressed the button, the item in the bay receives a bath of UVC rays that kill bacteria and viruses.
IMPORTANT: The UVC lights automatically turn off when the top of the bay is opened.
The charging port charges your mobile device when the clock/ sanitizer is plugged in. Just plug your charging cable into the port—your device charges both when the clock/sanitizer is sanitizing and when it’s not.

About UV sanitizing

Ultraviolet (UV) light is invisible to the human eye. The UVC part of the UV spectrum is proven to have germicidal benefits, killing bacteria and deactivating viruses. It is important to use the product with appropriate safeguards and follow safety precautions. UV light is most effective on hard, non-porous surfaces such as phones, most phone cases, keys, credit cards, etc. UV light is less effective against fabrics and other porous materials because of the many shadows they create that may block the UV light from hitting the surface. The UV light can only kill germs on surfaces with which it comes in contact.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals