microlife NC150 BT Non Contact Thermometer Instruction Manual

: June 6, 2024
: microlife

Table of Contents

Microlife NC150 BT Overview
The Advantages of this Thermometer
Important Safety Instructions
How this Thermometer measures Temperature
Control Displays and Symbols
Setting Date, Time and Beeper Functions
Changing between Body and Object Mode
Directions for Use
How to recall 30 readings in Memory Mode
Bluetooth Function
Error Messages
Cleaning and Disinfecting
Battery Replacement
Guarantee
Technical Specifications
www.microlife.com
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

microlife NC150 BT Non Contact Thermometer Instruction Manual

Overview

Microlife NC150 BT Overview

Product Overview

Measuring sensor
Tracking light
Display
START button
ON/OFF button
Mode switch
Battery compartment cover
M-button (memory)
All segments displayed
Memory
Ready for measuring
Measurement complete
Body mode
Object mode
Low battery indicator
Recall mode
Recall the last 30 readings
Measured temperature too high
Measured temperature too low
Ambient temperature too high
Ambient temperature too low
Error function display
Blank display
Flat battery
Date/Time
Beeper function setting
Replacing the battery

Microlife Non Contact Thermometer NC150 BT

Read the instructions carefully be fore using this device
Type BF applied part
Keep dry

This Microlife thermometer is a high quality product incorporating the latest technology and tested in accordance with international standards. With its unique technology, this device can provide a stable, heat-interference-free reading with each measurement.
The device performs a self test every time it is switched on to always guarantee the specified accuracy of any measurement.
This Microlife thermometer is in tended for the periodic measurement and monitoring of human body temperature.
This thermometer has been clinically tested and proven to be safe and accurate when used in accordance to the operating instruction manual.

Please read through these instructions carefully in order for you to understand all functions and safety information.

The Advantages of this Thermometer

Measures in a matter of seconds
The innovative infrared technology allows the measurement without even touching the object. This guarantees safe and sanitary measurements within seconds.

Multiple uses (wide range of measurement)
This thermometer offers a wide range of measurement from 0.1 – 99.9 °C , meaning the unit can be used to measure body temperature or it also has a feature allowing it to be used to measure surface temperature of the following examples:

Milk surface temperature in a baby’s bottle
Surface temperature of a baby’s bath
Ambient temperature

Accurate and reliable
The unique probe assembly construction incorporates an advanced infrared sensor, ensuring that each measurement is accurate and reliable.

Gentle and easy to use

The ergonomic design enables simple and easy use of the thermometer.
This thermometer can even be used on a sleeping child without causing any interruption.
This thermometer is quick, therefore child-friendly.

Multiple readings recall
Users will be able to recall the last 30 readings with a record of both time and date when entering the recall mode, enabling efficient tracking of temperature variations.

Safe and hygienic

No direct skin contact.
No risk of broken glass or mercury ingestion.
Completely safe for use on children.

Fever alarm
10 short beeps and a red LCD backlight alert the patient that he/ she may have a temperature equal to or higher than 37.2 °C.

Bluetooth Function
This device connects to the «Microlife Connected Health+» App by using Bluetooth® 4.0 and enables easy monitoring of temperature.

Important Safety Instructions

Follow instructions for use. This document provides important product operation and safety information regarding this device.
Please read this document thoroughly before using the device and keep for future reference.
This device may only be used for the purposes described in these instructions. The manufacturer cannot be held liable for damage caused by incorrect application.
Never immerse this device in water or other liquids. For cleaning please follow the instructions in the «Cleaning and Disinfecting» section.
Do not use this device if you think it is damaged or notice anything unusual.
Never open this device.
A basic physiological effect called vasoconstriction can occur in the early stages of fever, resulting in a cool skin effect. The recorded temperature using this thermometer can, therefore, be unusually low.
If the measurement result is not consistent with the patient’s finding or unusually low, repeat the measurement every 15 minutes or double check the result by another core body temperature measurement.
This device comprises sensitive components and must be treated with caution. Observe the storage and operating conditions described in the «Technical Specifications» section.
Ensure that children do not use this device unsupervised; some parts are small enough to be swallowed.
Do not use this device close to strong electromagnetic fields such as mobile telephones or radio installations. Keep a minimum distance of 3.3 m from such devices when using this device.
Protect it from:
- extreme temperatures
- impact and dropping
- contamination and dust
- direct sunlight
- heat and cold
If the device is not going to be used for a prolonged period the batteries should be removed.

WARNING: The measurement results given by this device is not a diagnosis. It is not replacing the need for the consultation of a physician, especially if not matching the patient’s symptoms. Do not rely on the measurement result only, always consider other potentially occurring symptoms and the patient’s feedback. Calling a doctor or an ambulance is advised if needed.

How this Thermometer measures Temperature

This thermometer measures infrared energy radiated from the forehead as well as objects. This energy is collected through the lens and converted to a temperature value.

Control Displays and Symbols

All segments displayed 9: Press the ON/OFF button 5 to turn on the unit; all segments will be shown for 1 second.
Ready for measuring AK: When the unit is ready for measuring, the «°C» icon will keep flashing while the mode icon (body or object) will be displayed.
Measurement complete AL: The reading will be shown on the display 3 with the «°C» icon and the mode icon steady. The unit is ready for the next measurement as soon as the «°C» icon is flashing again.
Low battery indicator AO: When the unit is turned on, the « » icon will keep flashing to remind the user to replace the batteries.

Setting Date, Time and Beeper Functions

Setting the date and time

After the new batteries are fitted, the year number flashes in the display 25. You can set the year by pressing the START button
To confirm and then set the month, press the M-button 8.
Press the START button 4 to set the month. Press the Mbutton 8 to confirm and then set the day.
Follow the previously mentioned instructions to set the day, 12 or 24 hour mode, hours and minutes.
Once you have set the minutes and pressed the M-button 8 , the date and time are set and the time is displayed.
** If no button is pressed for 20 seconds, the device automatically switches to ready for measuring AK.
Cancel time setup: Press the ON/OFF button 5 during time setup. The LCD will show Date/Time icons with «–:–». After that press the ON/OFF button 5 to start the measurement. If no further action is taken within 20 seconds, the
device will automatically turn off.
Change current date and time: Press and hold the Mbutton 8 for approx. 3 seconds until the year number starts to flash 25.** Now you can enter the new values as described above.

Setting the beeper

When the device is switched off, press and hold the ON/OFF button 5 for 5 seconds to set the beeper 26.
Press the ON/OFF button 5 again to either turn the beeper on or off. The beeper is activated when the beeper icon 26 is not crossed-out.
**** If no button is pressed for 5 seconds, the device automatically switches to ready for measuring AK.

Changing between Body and Object Mode

For changing from body to object mode, slide the mode switch 6 at the side of the thermometer downwards. For switching back to body mode, slide the switch up again.

Directions for Use

Measuring in body mode

Press the ON/OFF button 5. The display 3 is activated to show all segments for 1 second.
When the «°C» icon is flashing, a beep sound is heard and the thermometer is ready for measuring AK.
Aim the thermometer at the center of the forehead with a distance of no more than 5 cm. Please remove any hair, sweat or dirt from the forehead before measuring to improve the accuracy of the readings.
Press the START button 4 and ensure that the activated blue tracking light is aimed at the center of the forehead.
After 1 second a long beep will verify the completion of measurement.
Read the recorded temperature from the LCD display.

Measuring in object mode

Follow steps 1-2 above, then aim the thermometer at the center of the object you want to measure with a distance of no more than 5 cm. Press the START button 4. After 1 second a long beep will verify the completion of measurement.
Read the recorded temperature from the LCD display.

NOTE:

Patients and thermometer should stay in similar room condition for at least 30 minutes.
Don’t take a measurement while or immediately after nursing a baby.
Don’t use the thermometer in high humidity environments.
Patients should not drink, eat or exercise before/while taking the measurement.
Don’t move the measurement device from the measuring area before hearing the termination beep.
10 short beeps and a red LCD backlight alert the patient that he/she may have a temperature equal to or higher than 37.2 ° C.
Always take the temperature in the same location, since temperature readings may vary according to locations.
Doctors recommend rectal measurement for newborn infants within the first 6 months, as all other measuring methods might lead to ambiguous results. If using a non contact thermometer on those infants, we always recommend verifying the readings with a rectal measurement.
In the following situations it is recommended that three temperatures are taken with the highest one taken as the reading:

Children under three years of age with a compromised immune system and for whom the presence or absence of fever is critical.
When the user is learning how to use the thermometer for the first time until he/she has familiarized himself/herself with the device and obtains consistent readings.
If the measurement is surprisingly low.

Readings from different measuring sites should not be compared as the normal body temperature varies by measuring site and time of day, being highest in the evening and lowest about one hour before waking up.

Normal body temperature ranges:

Axillar: 34.7 – 37.3 °C
Oral: 35.5 – 37.5 °C
Rectal: 36.6 – 38.0 °C
Microlife NC 150 BT: 35.4 – 37.4 °C

How to recall 30 readings in Memory Mode

This thermometer can recall the last 30 readings with a record of both time and date.

Recall mode 16 Press the M-button 8 to enter recall mode when the power is off. The memory icon «M» will flash.
Reading 1 – the last reading 17 Press and release the Mbutton 8 to recall the last reading. Number «1» and a flashing «M» are displayed.
Reading 30 – readings in succession: Press and release the M-button 8 consecutively to recall the last 30 readings in succession.

Pressing and releasing the M-button 8 after the last 30 readings have been recalled will resume the above sequence from reading 1.

Bluetooth Function

This device can be used in conjunction with a smartphone running the «Microlife Connected Health+» App. The measurement results will be automatically transferred via Bluetooth®.

Downloading the «Microlife Connected Health+» App
Download «Microlife Connected Health+» App for free from Google Play™ (Android) or App Store (iOS) and install it on your smartphone.

How the Bluetooth® Function Works
The Bluetooth® function on your device will automatically turn on and will be ready to connect with the «Microlife Connected Health+» App after the device is switched on. Your device will automatically upload the data once it is connected to the smartphone.

Bluetooth® Icon Indicator
The Bluetooth® icon indicator on your device, located in the middle left portion of the display, is designed to provide information about the connection between your device and smartphone.

NOTE:

The Bluetooth® function is enabled: The Bluetooth® icon indicator 11 appears steady on the display.
The Bluetooth® icon indicator AK flashes, when connecting with a device or uploading data to the device.
The Bluetooth® function is automatically switched off during measurement; after measurement the device will switch it on and upload the data to the «Microlife Connected Health+» App.

App Tutorial

To access the tutorial, select «Tutorial» in the menu of the «Microlife Connected Health+» App (located in the upper left corner on the screen).

Error Messages

Measured temperature too high 18: Displays «H» when measured temperature is higher than 43 °C in body mode or 99.9 °C in object mode.
Measured temperature too low 19: Displays «L» when measured temperature is lower than 34.0 °C in body mode or 0. 1°Ci n object mode.
Ambient temperature too high 20: Displays «H» and when ambient temperature is higher than 40.0 °C
Ambient temperature too low 21: Displays «L» and when ambient temperature is lower than 15.0 °C in body mode or lower than 5.0 °C in object mode.
Error function display 22: The system has a malfunction.
Blank display 23: Check if the batteries have been inserted correctly. Also check polarity (<+> and <->) of the batteries.
Flat battery indicator 24: If only « » icon is shown on the display, the batteries should be replaced immediately.

Cleaning and Disinfecting

Use an alcohol swab or cotton tissue moistened with alcohol (70% Isopropyl) to clean the thermometer casing and the measuring sensor. Ensure that no liquid enters the interior of the device. Never use abrasive cleaning agents, thinners or benzene for cleaning and never immerse the device in water or other cleaning liquids. Take care not to scratch the surface of the sensor lens and the display.

Battery Replacement

This device is supplied with 2 new, long-life 1.5V, size AAA batteries. Batteries need replacing when this icon « » BN is the only symbol shown on the display.
Remove the battery cover 27 by sliding it in the direction shown. Replace the batteries – ensure correct polarity as shown by the symbols in the compartment.

Batteries and electronic devices must be disposed of in accordance with the locally applicable regulations, not with domestic waste.

Guarantee

This device is covered by a 2 year guarantee from the date of purchase. The guarantee is valid only on presentation of the guarantee card completed by the dealer (see back) confirming date of purchase or the receipt.

The guarantee covers the device. Batteries and packaging are not included.
Opening or altering the device invalidates the guarantee.
The guarantee does not cover damage caused by improper handling, discharged batteries, accidents or non-compliance with the operating instructions.

Please contact Microlife-service.

Technical Specifications

Type: Non Contact Thermometer NC150 BT
Measurement: Body mode: 34.0 – 43.0 °C
Range: Object mode: 0.1 – 99.9 °C
Resolution: 0.1 °C
Measurement accuracy (Laboratory):
- Body mode:
  ±0.2 °C, 35.0~42.0 °C
  ±0.3 °C, 34.0~ 34.9 °C and 42.1~ 43.0 °C
  Object mode:
  ±1.0 °C, 0.1~ 99.9 °C
  Liquid Crystal Display, 4 digits plus special icons
Display:
Acoustic:
- The unit is turned ON and ready for the measurement: 1 short beep.
- Complete the measurement: 1 long beep (1 sec.) if the reading is less than 37.2 °C , 10 short «beep» sounds, if the reading is equal to or greater than 37.2 °C .
- System error or malfunction: 3 short «bi» sounds.
Memory: 30 readings recall in the memory mode with a record of both time and date.
Backlight:
The display light will be GREEN for 1seconds, when the unit is turned ON.
The display light will be GREEN for 5 seconds, when a measurement is completed with a reading less than 37.2 °C .
The display light will be RED for 5 seconds, when a measurement is completed with a reading equal to or higher than 37.2 °C
Operating conditions:
Body mode: 15 – 40.0 °C
Object mode: 5 – 40.0 °C
30 – 75 % relative maximum humidity
Storage conditions:
–20-+60℃±2℃
91 – 95 % relative maximum humidity
Automatic Switch-off: Approx. 1 minute after last measurement has been taken.
Communication: Bluetooth® Low Energy 4.0 (Bluetooth® Smart)
Compatibility:
iOS: iOS 9.0 or newer
Android: Android 4.4 or newer
Battery: 2 x 1.5 V alkaline batteries; size AAA
Battery lifetime: approx. 1500 measurements (using new batteries)
Dimensions: 141.1 x 43.3 x 36.9 mm
Weight: 90 g (with batteries), 67 g (w/o batteries)
IP Class: IP21
Reference to standards: ASTM E1965; IEC 60601-1; IEC 60601-1-2 (EMC); IEC 60601-1-11
Expected service life: 5 years or 12000 measurements

This device complies with the requirements of the Medical Device Directive 93/42/EEC.
Technical alterations reserved.
According to the Medical Product User Act a biennial technical inspection is recommended for professional users. Please observe the applicable disposal regulations.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Microlife Corp. is under license. Other trademarks and trade names are those of their respective owners.