DELL S2319HS 23 inch Monitor Instructions
- June 6, 2024
- Dell
Table of Contents
DELL S2319HS 23 Inch Monitor Instructions
Disassembly Procedures
S1 Open the Pizza carton with a proper tool.
S2 Take out all of the accessories including DP QSG, cable, power cable, USB cable, CD&user’s manual, stand and base from the carton from the carton.(Note: It depends on whether users returning the accessories)
S3 Take out of the Paper-top and monitor from the carton, then take out the monitor from the EPE bag and put the LCD monitor on a protective cushion.
S4 Use a Philips-head screwdriver to remove four screws for unlocking mechanisms.
(No.1~4 screw size=M4x10; Torque=12±0.5kgfxcm)
S5 Wedge your fingers between the rear cover and the middle bezel on the corners of the top side of the monitor to release the rear cover, then use one hand to press the middle bezel, the other hand to pull up carefully the rear cover in order of arrow preference for unlocking mechanisms of rear cover..
S6 Lift the rear cover up carefully. Disconnect the USB FFC cable from the connector of the interface board, and then remove the rear cover.
S7 Use a Philips-head screwdriver to remove one screw for unlocking the USB board unit, then release the USB board unit and put it aside.
(No.1 screw size=M3x6, Torque=4±0.5kgfxcm)
S8 Tear off two pieces of the aluminium foils for unfixing S8 the bracket chassis base.
S9 Unplug the panel power cable from the connector of the panel module, then release the function by tearing the tapes on the back of the cable, and then release the cable from the hooks of the middle bezel.
S10 Use a proper tool to release the function key cable from the connector, then pull the function key cable high for releasing the function key cable.
S11 Use a Philips-head screwdriver to remove 2pcs screws for unlocking the bracket with the panel. Push the earing-lock, and disconnect the LVDS cable from the connector of LCD panel module.
(No.1~2 screw size=M3x2.8, Torque=2~3kgfxcm)
S12 Use a Philips-head screwdriver to remove 13pcs screws for unlocking the middle bezel with the assembled unit.
(No.1~11 screw size=M3x4, Torque=3~4kgfxcm; No.12~13 screw size=M1.6×1.7, Torque=0.6~1kgfxcm)
S13 Take away the . middle bezel, and put it on a fixture, then use a Philips-head screwdriver to remove 3pcs screws for unlocking the function key board with the middle bezel.
S14 Lift up the panel module for releasing the front bezel S14 away from the panel module.
S15 Take away the bracket chassis module and then put the bracket chassis module on a protective cushion.
S16 Use a Hex-head screwdriver to remove two screws for unlocking the D-Sub connector.
(No.1~2 screws size=M3x8, Torque=6±0.5kgfxcm)
Use a Philips-head screwdriver to remove two screws for unlocking the AC power outlet.
( No.3~4 screw size=M3x8, Torque=6~7kgfxcm)
S17 Remove the Mylar from the hooks of the bracket. Use a Philips-head screwdriver to remove six screws for unlocking the circuit board, release all the cables from the hooks.
(No.1~5 screw size=M3x7.5, Torque=6±0.5kgfxcm; No. 6 screw size=M4x8, Torque=6±0.5kgfxcm)
S18 Remove the interface board and power board from the bracket chassis module carefully, and disconnect all the cables.
S1- Remove electrolyte capacitors (red mark) from printed circuit boards
S1 -1 Cut the glue between bulk cap. and PCB with a knife
S1 -2 Ensure cutting path within the glue, don’t touch bulk cap. or PCB
S1 -3 Cut into the bottom of bulk cap. and pull it up carefully
S1 -4 Take out bulk cap. pin solder with soldering iron and absorber
S1 -5 Lift the bulk cap. up and away from the PCB
Product material information
The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.
Tools Required
List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed.
Tool Description:
- Screwdriver (Phillip head) #1
- Screwdriver (Phillip head) #2
- Penknife
- Soldering iron and absorber
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>