DAKOTA MICRO DMRZ-LC-P RazerCam CVBS 170° NTSC PAL Camera User Manual
- June 9, 2024
- DAKOTA MICRO
Table of Contents
DMRZ-LC-P RazerCam CVBS 170° NTSC PAL Camera
User Manual
Camera Specifications
Description | This RazerCamTM kit includes one (1) AHD 170° NTSC Camera |
---|---|
Part Numbers | DMRZ-HC |
Video System | NTSC |
Video Type | Analog High Definition |
Image Pick-up Device | CMOS |
Horizontal Resolution | 720P |
Minimum Illumination | 0.01 LUX@F1.2 |
Image Ratio | 16:09 |
Auto Gain Control | Automatic based on lighting |
Scanning System | Progressive |
Camera Board Lens | 170° Field of View |
Operating Temp | -4°F (-20°C) — 158°F (70°C) |
Construction | Aluminum Case |
Waterproofing Criteria | IP69K |
Dimensions | 1.76in(44.7mm) (W) x 1.09in(27.7mm) (D) |
Camera Connector | 5 pin Conxall/ Switchcraft |
LED Lighting | Visible White Light |
Warranty Period | 1 Year |
Camera Installation Instructions
-
The opening size for camera mounting should be 1.38in (35.1mm). The perfect hole drill bit size is a 1 3/8 or 35mm. While not perfect, a 1 7/16 or 37mm will work.
-
Make sure that your camera is mounted so that the word “RazerCam” is right side up.
-
Tighten the Hex Nut to hold the camera into place.
-
Near the 5-pin connector on your camera is a small loop of green wire. This wire is your mirroring switch. When the circuit is complete (intact) your camera image is mirroring. When this circuit is incomplete (cut) your camera is forward-facing. It is recommended to place shrink wrap or electrical tape over the exposed wire ends to prevent shorts. If utilizing a Dakota Micro monitor your camera can also be mirrored from the monitor. Your camera will need to be rebooted (powered on/off) for this switch to take effect
-
Your RazerCamTM camera has an IR array that outputs visible white light. If you mount this camera close to another light source, your viewing in darkened environments will be increased.
Camera Warnings
NEVER RELY ON YOUR DAKOTA MICRO CAMERA AS A SAFETY FEATURE. It is up to your
discretion to keep your road travel and other operations safe. Your Dakota
Micro camera will provide you with information only based on what it sees.
Operation of machinery safety guidelines still apply.
Dakota Micro, Inc. cameras are equipped with an array of light emitters which
are visible to the human eye. This feature will aid in low light conditions
but has limitations. The effective range of the night vision feature is 1 to
75+ feet. DO NOT ATTEMPT TO DRIVE MACHINERY USING THIS FEATURE.
Always read the manual prior to operating this equipment. Also, please
follow all safety signs and precautions.
Consumer Limited Warranty
Subject to the disclaimer, limitations and other directions stated hereafter,
Dakota Micro, Inc. warrants that the Product will be free from defects in
material and workmanship for periods as stated hereafter from the date of
original purchase. THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS. THE EXCLUSIVE REMEDY OF THE BUYER IS LIMITED TO
REPAIR OR REPLACEMENT OF THE PRODUCT. EXCEPT AS STATED IN THIS WARRANTY,
DAKOTA MICRO, INC. SHALL NOT BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE,
INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, RESULTING
FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER RESULTING FROM BREACH OF
WARRANTY, NEGLIGENCE, STRICT LIABILITY OF ANY OTHER LEGAL THEORY. Any oral
statements or representations made by anyone which are contrary to or at
variance with the terms stated in this LIMITED WARRANTY are void.
Dakota Micro, Inc. will, at its option, either repair the defect or replace
the defective Product or part thereof with a new or remanufactured equivalent
at no charge to the purchaser for parts or labor for the period of three (3)
years for AgCam® /EnduraCam® and InnoPro® cameras; two (2) years for AgCam®/
EnduraCam® monitors, and Wireless components; Twelve (12) Months for all
Overview® and RazerCamTM Cameras & Monitors, cables and all other accessories.
The Dakota Micro, Inc. limited warranty periods outlined above apply
throughout the United States and Canada only. A one (1) year maximum limited
warranty for all Products applies to all other geographic locations unless
otherwise stated in writing by Dakota Micro, Inc.
This limited warranty does not apply to any issues connected with appearance
that have no relation to the performance of the Product nor to any Product the
exterior of which has been damaged or defaced, which has been subjected to
improper voltage or other misuse, abnormal service or handling, or which has
been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser
should follow the process set forth in the Product Warranty/Repair Process,
and provide proof of purchase to Dakota Micro, Inc.
Neither the sales personnel of Dakota Micro, Inc. nor any dealer or any other
person is authorized to make any warranties other than those described herein,
or to extend the duration of any warranties beyond the time periods described
herein.
The warranties described herein shall be the sole and exclusive warranties and
remedies provided by Dakota Micro, Inc. Correction of defects, in the manner
and for the period of time described herein, shall constitute complete
fulfillment of all liabilities and responsibilities of Dakota Micro, Inc. to
the purchaser with respect to the Product, and shall constitute full
satisfaction of all claims. In no event shall Dakota Micro, Inc. be liable or
in any way responsible for any damages or defects in the Product which were
caused by repairs or attempted repairs performed by anyone other than Dakota
Micro, Inc.
Some states do not allow the limitation or exclusion of incidental or
consequential damages, so said limitation may not apply to you.
Any action at law, suit in equity, or other judicial proceeding for the
enforcement of any right provided for herein or otherwise, or with respect to
any claim that a purchaser may have against Dakota Micro, Inc. shall be
instituted only in the Courts of the State of North Dakota, either in the
state district court located in Wahpeton, North Dakota or in Federal District
Court located in Fargo, North Dakota. Without regard to conflicts of law
principles, the laws of the state of North Dakota shall govern the
interpretation and enforcement of the terms of this Limited Warranty and all
aspects of the relationship between Dakota Micro, Inc., and the purchaser.
This warranty gives you specific legal rights and you may also have other
rights, which may vary from state to state.
8659 148½ Ave. SE.
Cayuga, ND 58013
www.dakotamicro.com
Management System
Registered to ISO 9001
User Manual DMRZ-LC(P)
User Manual
RazerCamTM CVBS 170° NTSC (PAL) Camera
Camera Specifications
Description Part Numbers Video System Video Type Image Pick-up Device Horizontal Resolution Minimum Illumination Image Ratio Auto Gain Control Scanning System Camera Board Lens Operating Temp Construction Waterproofing Criteria Dimensions Camera Connector LED Lighting Warranty Period
This RazerCamTM kit includes one (1) CVBS 170° camera DMRZ-LC (NTSC) or DMRZ- LCP (PAL) NTSC or PAL CVBS CMOS 480P 0.01 LUX@F1.2 16:9 Automatic based on lighting Progressive 170° Field of View -4°F (-20°C) 158°F (70°C) Aluminum Case IP69K 1.76in(44.7mm) (W) x 1.09in(27.7mm) (D) 5 pin Conxall/ Switchcraft Visible White Light 1 Year
Camera Installation Instructions
1. The opening size for camera mounting should be 1.38in (35.1mm). The
perfect hole drill bit size is a 1 3/8 or 35mm. While not perfect, a 1 7/16 or
37mm will work.
2. Make sure that your camera is mounted so that the word “RazerCam” is right
side up.
3. Tighten hex nut to hold the camera in place. 4. Near the 5-pin connector
on your camera is a
small loop of green wire. This wire is your mirroring switch. When the circuit
is complete (intact) your camera image is mirroring. When this circuit is
incomplete (cut) your camera is forward-facing. It is recommended to place
shrink wrap or electrical tape over the exposed wire ends to prevent shorts.
If utilizing a Dakota Micro monitor your camera can also be mirrored from the
monitor. Your camera will need to be rebooted (powered on/off) for this switch
to take effect. 5. Your RazerCamTM camera has an IR array that outputs visible
white light. If you mount this camera close to another light source, your
viewing in darkened environments will be increased.
Camera Warnings
NEVER RELY ON YOUR DAKOTA MICRO CAMERA AS A SAFETY FEATURE. It is up to your
discretion to keep your road travel and other operations safe. Your Dakota
Micro camera will provide you with information only based on what it sees.
Operation of machinery safety guidelines still apply.
Dakota Micro, Inc. cameras are equipped with an array of light emitters which
are visible to the human eye. This feature will aid in low light conditions
but has limitations. The effective range of the night vision feature is 1 to
75+ feet. DO NOT ATTEMPT TO DRIVE MACHINERY USING THIS FEATURE.
Always read the manual prior to operating this equipment. Also, please follow all safety signs and precautions.
AU: SJE
BY: SJE
V3
REV: 01/05/23
Page 1 of 2
User Manual DMRZ-LC(P)
Consumer Limited Warranty
Subject to the disclaimer, limitations and other directions stated hereafter,
Dakota Micro, Inc. warrants that the Product will be free from defects in
material and workmanship for periods as stated hereafter from the date of
original purchase. THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS. THE EXCLUSIVE REMEDY OF THE BUYER IS LIMITED TO
REPAIR OR REPLACEMENT OF THE PRODUCT. EXCEPT AS STATED IN THIS WARRANTY,
DAKOTA MICRO, INC. SHALL NOT BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE,
INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, RESULTING
FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER RESULTING FROM BREACH OF
WARRANTY, NEGLIGENCE, STRICT LIABILITY OF ANY OTHER LEGAL THEORY. Any oral
statements or representations made by anyone which are contrary to or at
variance with the terms stated in this LIMITED WARRANTY are void.
Dakota Micro, Inc. will, at its option, either repair the defect or replace
the defective Product or part thereof with a new or remanufactured equivalent
at no charge to the purchaser for parts or labor for the period of three (3)
years for AgCam® /EnduraCam® and InnoPro® cameras; two (2) years for AgCam®/
EnduraCam® monitors, and Wireless components; Twelve (12) Months for all
Overview® and RazerCamTM Cameras & Monitors, cables and all other accessories.
The Dakota Micro, Inc. limited warranty periods outlined above apply
throughout the United States and Canada only. A one (1) year maximum limited
warranty for all Products applies to all other geographic locations unless
otherwise stated in writing by Dakota Micro, Inc.
This limited warranty does not apply to any issues connected with appearance
that have no relation to the performance of the Product nor to any Product the
exterior of which has been damaged or defaced, which has been subjected to
improper voltage or other misuse, abnormal service or handling, or which has
been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser
should follow the process set forth in the Product Warranty/Repair Process,
and provide proof of purchase to Dakota Micro, Inc.
Neither the sales personnel of Dakota Micro, Inc. nor any dealer or any other
person is authorized to make any warranties other than those described herein,
or to extend the duration of any warranties beyond the time periods described
herein.
The warranties described herein shall be the sole and exclusive warranties and
remedies provided by Dakota Micro, Inc. Correction of defects, in the manner
and for the period of time described herein, shall constitute complete
fulfillment of all liabilities and responsibilities of Dakota Micro, Inc. to
the purchaser with respect to the Product, and shall constitute full
satisfaction of all claims. In no event shall Dakota Micro, Inc. be liable or
in any way responsible for any damages or defects in the Product which were
caused by repairs or attempted repairs performed by anyone other than Dakota
Micro, Inc.
Some states do not allow the limitation or exclusion of incidental or
consequential damages, so said limitation may not apply to you.
Any action at law, suit in equity, or other judicial proceeding for the
enforcement of any right provided for herein or otherwise, or with respect to
any claim that a purchaser may have against Dakota Micro, Inc. shall be
instituted only in the Courts of the State of North Dakota, either in the
state district court located in Wahpeton, North Dakota or in Federal District
Court located in Fargo, North Dakota. Without regard to conflicts of law
principles, the laws of the state of North Dakota shall govern the
interpretation and enforcement of the terms of this Limited Warranty and all
aspects of the relationship between Dakota Micro, Inc., and the purchaser.
This warranty gives you specific legal rights and you may also have other
rights, which may vary from state to state.
AU: SJE
BY: SJE
8659 148½ Ave. SE. Cayuga, ND 58013 www.dakotamicro.com Management System Registered to ISO 9001
V3
REV: 01/05/23
Page 2 of 2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>