juice Charger Me 3 User Manual

juice Charger Me 3

Important: Read this User Manual before you start using the device!
Failure to comply with these instructions can result in injury or death, damage to the device and harm to the environment. Keep this User Manual in a safe place to-gether with the charging equipment. Always provide any new users of the device with the User Manual as well.

Warnings

The following warning and hazard symbols are used in this User Manual:

DANGER

Texts marked with this symbol contain information for your safety and point out hazards that present the danger to you of serious or even fatal injuries.

WARNING

Texts displaying this symbol indicate potential hazards that pose risk of injury.

CAUTION

This symbol is intended to make you aware of potential risks of damage that demand your heightened caution.

Intended use

• Use the JUICE CHARGER me 3 and its accessories (re-ferred to collectively below also as charging equipment) exclusively to charge the batteries of electric vehicles that are equipped with a fitting vehicle charging connec-tion socket.
• Use the JUICE CHARGER me 3 only as intended and specified in this User Manual. Use only genuine original accessories from JUICE TECHNOLOGY AG. The use of any other accessories is prohibited and constitutes improper, non-compliant use.
• Any other use will be deemed improper and may result in severe injury or damage to property. The manufac-turer and dealers will not accept any liability for damage caused by improper use. What’s more, the equipment warranty becomes void in such cases.

Safety information

DANGER

Failure to observe these safety instructions can cause short circuits, electric shock, explosions, fires, burns or other, fatal personal injuries as well as property damage.

• Check the charging equipment for damage or soiling prior to every use. Should any damage or soiling be evident, do not put the equipment in operation.
• If damage occurs while charging, disconnect the charging equipment if possible immediately from the power mains, for example by switching off the mains fuse/circuit breaker. Do not touch any electrically live parts.
• Charge your vehicle only at professionally installed, tested and undamaged charging stations and from properly functioning electrical installations.
• Never charge batteries using this device with the cables coiled. This can lead to overheating and cause the cable shielding to melt.
• Never operate the JUICE CHARGER me 3 near explo-sive vapours or gases. Switching operations within the device can generate tiny electric sparks, which could ignite explosions.
• Never touch the contact surfaces of the charging equipment. Do not insert any objects into the charging equipment connector faces.
• Clean your charging equipment only when it is completely disconnected from vehicle. Use a slightly damp cloth for cleaning, and afterwards carefully dry off all parts.
• Do not attempt to modify or repair your charging equipment in any way yourself. The unit housing should only be opened by an electrically skilled person.
• Properly dispose of the equipment packaging materials in a workmanlike manner; such materials are not suitable as toys. Keep your charging equipment out of reach of under-age persons.

WARNING

Failure to observe these warnings can lead to electric shock or fire, or damage the charging equipment.

• Only qualified, electrically skilled persons are permit-ted to install and commission the JUICE CHARGER me 3. Such expert electricians bear full responsibility for ensuring compliance with the existing codes, stand-ards and regulations in force.
• Do not immerse the charging equipment in water, and do not directly expose it to water spray (e.g. from high-pressure cleaners or garden hoses).
• Never disconnect the JUICE CHARGER me 3 from the vehicle when the charger is electrically live (i.e. during charging operations), as this can lead to fouling of the connector plug contacts, and damage the charging electronics and electrical systems in your vehicle as well as in the JUICE CHARGER me 3. Always stop the charging process first at the controls inside the vehicle.
• Do not expose your charging equipment to large amounts of dust, highly humid or moist environments, or aggressive liquids.
• The JUICE CHARGER me 3 is intended for use in pri-vate households and semi-public areas (e.g. on private property or company parking lots, etc.).
• During unattended charging operations, unauthorised parties (e.g. children, under-age persons, household pets or other animals) should not have access to the charging equipment and vehicle.
• The JUICE CHARGER me 3 can become hot if exposed to direct sunlight. If this occurs, do not touch or take hold of the device.

CAUTION

Failure to follow the instructions below can lead to property damage, fines or even punishment.

• The electrically skilled person installing the unit is responsible for ensuring compliance with all local reg-ulations governing the operation of charging stations.
• The electrical connection data of the JUICE CHARGER me 3 must match the data of the power supply grid.

Symbol legend **(symbols that appear in this User Manual and/or on the

charging equipment)**

• By using the CE marking, the manufacturer or distrib-utor declares that the product meets all applicable European regulations and standards (EU Declaration of Conformity of the European Community).
• By using the UK Conformity Assessed (UKCA) marking, the manufacturer or distributor declares that the product meets all applicable regulations and standards of the United Kingdom (UK Declaration of Conformity / UK Conformity Assessed).
• Products marked with this symbol meet the requirements of the EU Directives restricting the use of certain hazardous substances in electrical and electronic equipment.
• This symbol indicates the lowest possible tempera-ture (−30 °C) at which the device may be operated.
• Danger of electrical shock from hazardous voltage if used improperly.
• The surface of the charging equipment can become very hot if exposed to direct sunlight.
• This symbol indicates general danger or hazard. Read the User Manual to familiarise yourself with the charging equipment.
• This symbol indicates that this product’s protection rating meets the requirements of Protection Class IP67. This means that it is protected against dust and temporary immersion.
• This symbol indicates that the earth conductor is fixed and permanently connected.
• This product meets the requirements of Protection Class I in accordance with IEC Standard 61140 of the International Electrotechnical Commission.
• The charging equipment is suitable for operation up to an elevation of 2,000 metres above sea level.
• JUICE has planted a tree to compensate for the carbon footprint caused by the manufacture and transport of this device.
  Read more at juice.world/forest

Scope of supply

Standard equipment:

• JUICE CHARGER me 3
• Type-2 holder
• Two RFID cards

Parts:

1. JUICE CHARGER me 3
2. Vehicle connector for coupling to the vehicle charging socket (Type 2)
3. Cable gland with bend protection
4. 400-V, 32-A, 3-phase heavy-duty cable with control signal conductors
5. Function display
6. Display (only for the version with MID-compliant meter, EP-JCME3M)\

Function display

The LED information panel indicates the device’s operating status. Standby, charging, waiting, and fault condition is indicated by the corresponding four symbols lighting up in the display.

LED

|

Status

|
---|---|---
1| 3 lights lit in parallel| •  Authorisation process is running

•  Signalling of current authorisation by circular-shaped light pattern

2| Solid light| •  Charging system free

•  No vehicle connected

| Slowly blinking| •  Charging system free

•  Vehicle connected

3| Solid light| •  Charging system reserved

•  No vehicle connected

| Slowly blinking| •  Charging system reserved

•  Vehicle connected

| Rapidly blinking| •  Date being replaced from the back-end

•  Waiting for authorisation

4| Slowly blinking| •  Charging operation authorised

•  Vehicle is charging

| Rapidly blinking| •  Charging system authorised

•  Vehicle not yet connected or disconnected from the charging system

**2,3,4 ***| Rapidly blinking| •  Authorisation rejected

•  Error in the charging system

•  Back-end not available

Operating instructions

CAUTION

• Use the charging equipment only if you can ensure that the device has been correctly installed and connected to the grid by an electrically skilled person. The device charges your vehicle with single-, two- or three-phase AC voltage ranging from 6 to 32 ampere (A) or 6 to 16 A, depending on the model. Use only genuine, original JUICE accessories.
• Protect your charging equipment against damage from being run over, dropped, yanked, kinked or crushed.
• To prevent overheating while charging, do not expose your JUICE CHARGER me 3 to direct sunlight or other sources of heat for long periods of time. If the JUICE CHARGER me 3 becomes overheated, the charging power is automatically reduced until the unit’s tem-perature drops to within its normal operating range.
• In many countries, the power feeder line to charging stations must be equipped with a Type-A residual current device (RCD). Please observe the regulations in force in the country of use, as these always take precedence.

Charging instructions

DANGER

Always perform charging operations in the specified order of steps.

Potential charging faults are identified on the device’s function display. (You’ll find further information on this in the Function display table).

Vehicle-end charging connection
Please consult the vehicle user manual for information on plugging in the connector, locking and unlocking the coupling, stopping the charging process, unplugging the connector from the vehicle-end socket, and the status of charging and the connection at the vehicle.

Start the charging operation

1. Take the vehicle-end connector from the holder and remove the protective rubber cap from the vehicle-end connector.
2. Plug the (Type 2) vehicle-end connector into the vehicle’s charging socket. Once firmly coupled to the vehicle, this status is confirmed by the slowly blinking “2” symbol on the operating panel function display. Your vehicle interlocks the coupling to the vehicle for safety reasons.
3. Activate the charge using one of the two pre-pro-grammed RFID cards supplied with the charging equipment. This activation is confirmed by the slowly blinking “3” symbol on operating panel function display.
4. The charging process then begins. The start of charg-ing is indicated by the slowly blinking “4” symbol on the operating panel function display.

Stopping the charging process

1. Stop the charging process at the controls inside the vehicle.
2. The interlock securing the vehicle charging coupling is released.
3. Remove the vehicle-end connector from the car.
4. Set the protective rubber cap back in place on the connector or hang the vehicle-end connector back into the holder provided.

Maintenance and cleaning

Cleaning

• Disconnect the JUICE CHARGER me 3 from the power socket and the vehicle.
• Only clean the outside of the device. Use a soft, slightly damp or antistatic cloth.
• Do not use detergent or chemical agents to clean it.

Maintenance

The device basically requires no maintenance. Note that connectors and couplings are sensitive, high-performance parts, and their contacts must always be kept clean and dry. Moisture, dirt or corrosion on the connector contacts can degrade function performance, and cause the device to overheat or become defective. If plugs get wet, allow them to dry before using them. Always fit the equipment with the protective caps when not plugged in.
Repairs / modifications

Any repairs and/or modifications may only be performed by the manufacturer.

Warranty and guarantee

• Our products undergo strict quality control. Should any JUICE article fail to function flawlessly, however, we deeply regret such circumstances and request that you contact our Customer Service operations noted below. We’re gladly available by phone or e-mail if you wish to contact us.
• In addition to the statutory guarantee, we grant you a warranty covering all JUICE articles in accordance with the following terms and conditions. These provisions in no way restrict your legal rights.
• Any claims arising from the statutory guarantee or our warranty must be made immediately after becoming ware of the defect within the guarantee or warranty period. Both periods come into force from the date of purchase or delivery.

Warranty

• The warranty is valid for two years from the date of purchase and is regulated by law.

Guarantee

• The warranty period is 2 years from the date of pur-chase. The warranty applies on the continent where the device was purchased, and takes the form of a Bring-In warranty.
• During the warranty period, devices that are faulty due to material or manufacturing defects will be repaired or replaced at our discretion. Exchanged de-vices or parts thereof become our property. Exercise of the warranty shall not extend the warranty period or trigger a new warranty.

Making warranty claims

• Have the following documents ready, as they form the basis for making claims arising from your guarantee or warranty:
  • Delivery note (date of start of the warranty period)
  • Invoice (proof of purchase)
  • Owner & Warranty card with device serial number
• Please contact our Customer Service (see the section on Customer service).
• Do not under any circumstances send your device to one of our warehouses or to our headquarters without first making contact with us, as our Service Centres are located elsewhere. In such cases, the parcel would be returned to you at your own expense.
• If the defect is covered by the statutory guarantee or our warranty scope, you will receive either a new, a repaired or a replacement device within a reasonable period of time. In such cases, JUICE TECHNOLOGY AG assumes the cost for returning the device.

Exclusion from warranty
Warranty claims are void if:

• there is evidence of incorrect or inappropriate han-dling, operation or transport
• the device has not been used properly as intended
• accessories or spare parts other than those recom-mended or supplied by the manufacturer have been used
• the JUICE CHARGER is disconnected from the vehicle while in use
• the device is disconnected from the mains while in use
• there is corrosion on the plug contacts due to persis-tent humidity and/or damp
• water or other liquids ingress the device via unprotect-ed or unplugged plugs or connectors or through water feeder-line piping.
• the operating instructions have not been observed
• major environmental factors (humidity, heat, power surges, dust, etc.) impact the device
• damage is incurred due to short circuits or overvoltag-es generated by the vehicle
• if the appliance is returned in inappropriate protective packaging
• an accident or unforeseen event (e.g. lightning, water, fire, force majeure) occurs
• the safety precautions applicable to the device have not been taken
• if safety instructions and hazard warnings have not been heeded
• if force has been applied (e.g. if it has been subject to impact or collision, or if it has been dropped, run over, crushed, or destroyed)
• you have attempted to repair the device yourself
• the device has been tampered with by someone other than our authorised Service Centres
• modifications have been made to the device by any-one other than the manufacturer
• the housings, plugs or cables have been opened or tampered with.

The warranty does not cover:

• any type of conventional wear and tear, or wear to the housing, rubber parts, cables, cable sleeves or connectors;

Repairs
We’ll gladly repair any defects or damage to the device that are not (or no longer) covered by the warranty in re-turn for a charge. Please contact our Customer Service for an individual quote. You are responsible for shipping costs.
A processing fee will be charged for devices sent in without any defects or with defects that are not covered by the warranty in the event that the client decides not to have them repaired.

Customer Service

juice.world/service

Here’s the quickest way to contact Customer Service: Please complete and submit the on-line form under this address if you have any technical questions or wish to make a claim under the statutory guarantee or our warranty. We’ll take up your request immediately and provide you with the support you need.
Please always contact our Service team by telephone or e-mail or using the online form before sending in the product. The team will discuss the next steps with you, issue you a ticket number as needed, and provide you with the correct address for returning the product.
JUICE TECHNOLOGY AG
Customer Service
Phone +41 (0)41 510 02 19
E-Mail service@juice.world

General information

We reserve the right to make modifications in the inter-ests of technical improvement.
JUICE TECHNOLOGY AG cannot guarantee that all requirements, regulations, directives, guidelines, specifi-cations and standards are free of third-party intellectual property rights.

Note on the Technical Connection Rules for Low-Voltage:

In various countries, the local Technical Connection Rules for Low Voltage stipulate that the responsible power provider utility be notified of electric car charging stations (in many cases for devices up to 11-kW capacity) or that an authorisation or license be obtained from the utility (usually for 22-kW capacity units). Observe all local regulations or contract the electrically skilled person installing the device to do so.

Provider / manufacturer

JUICE TECHNOLOGY AG
CH-8184 Bachenbülach, Switzerland
www.juice.world
E-Mail : info@juice.world
Telephone: +41 (0)41 510 02 19
Attention: Do not send devices or goods to this address. Both the warehouse and the Service Department are on different sites and may vary depending on the country in question.
Goods sent to this address will be returned to the sender at the sender’s expense. We unfortunately have to charge the sender for any forwarding costs, customs duties and/or value added tax incurred due to return shipments.

Waste disposal and recycling

Please sort your waste!

Please do not dispose of this device in your standard household waste. This device is subject to the regulations defined in European Directive 2012/19/EU. Have your device disposed of by an authorised waste disposal and recycling firm and your local waste management authority. Please observe the currently pertinent regulations in force. In case of doubt, please contact your waste disposal facility.

Recycling

Recyclable goods: Separate the packaging and electrical device by material type for disposal. Place all paperboard and corrugated fibreboard in paper recycling, foils and films with a waste materials collection centre, and have the electronic components properly disposed of by a specialist electrical retailer or a local recycling centre.

17. EU/UK Declaration of Conformity

This product conforms with the following EU Directives and UK regulations and the following standards or norma-tive documents:

• 2011/65/EU (hazardous substances in electrical and electronic equipment)
• 2014/53/EU (radio equipment)
• 2014/32/EU (measuring instruments)
• Radio Equipment Regulations 2017
• Restriction of Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
• The Electric Vehicles (Smart Charge Points) Regula-tions 2021, No. 1467

EN 300 330 V2.1.1 EN 62479:2010
EN 50364:2018 EN IEC 61851-1:2019
EN IEC 61439-7:2020 EN 62196-1:2014
EN 62196-2:2017 IEC 62955:2018
EN 50620:2020 EN 301 489-3 V2.1.1
EN 301 489-1 V2.2.3 EN IEC 61851-21-2:2021
EN IEC 63000:2018 EN 61000-6-2:2005
EN 61000-6-3:2007 +A1+A2:2012

Installation

The JUICE CHARGER me 3 may only be installed and commissioned by electrically skilled persons. Install the JUICE CHARGER me 3 in accordance with the attached Installation Guide. Always disconnect the power supply before beginning with installation work.

Protection

It absolutely essential that a residual current device and a line circuit breaker be installed upstream of the device.
The line circuit breaker must be dimensioned in accord-ance with the charging device’s rating plate, the desired charging power and the given power feeder line (line length and cross-sectional area) in compliance with the applicable national regulations. One line circuit breaker is needed for each charging point.

Operating modes / Charging power

RFID activation
RFID activation is set up as a standard feature. You receive two pre- programmed cards for activation.

Other operating modes

• Plug and Charge (ISO 15118)
• Master-slave load management

Changing the operating mode / charging power
If you wish to register an additional RFID card, change your operating mode or your charging power, you must connect your charging station to the Internet to do so.
Visit www.juice.world/installation to find out what next steps to take.

Specifications

AC, 50 Hz
Power output| 11 kW (16 A, three-phase) / 22 kW (32 A, three-phase)
Energy metering| Optional integrated MID-compliant meter (EP-JCME3M), readable via

viewing window in screen

Communication| OCPP1.5/1.6, Modbus TCP, EEBUS

Ethernet interface (LAN, RJ45)

Activation

__

| RFID reader for controlled access (MIFARE Classic / Desfire) The RFID frequency is 13.56 MHz.
Charging/load management

| Configurable as master and slave operation (up to 250 units)
Safety| Internal temperature sensor for reducing the charging current independently of the ambient temperature
Protection class| IP67
impact protection| IK10
Operating temperature

__

| −30 °C to +50 °C
Residual-current device| RCD DC 6 mA integrated
Protection class| I
Standards| IEC 61851, IEC 61439-7, EMC (Environments A + B), RoHS

Optional MID-compliant meter: EN 50470, EMC (Environments A + B),

RoHS

Material – colour| Base: ABS/PC blend, black Lid: PC, transparent

Frame: ABS/PC blend, silver Screen: PMMA, printed

Connection| Fixed, permanent connection installed by a certified electrically skilled

person

Vehicle-end connector| Type 2 (IEC 62196)
|

References

• JUICE WORLD | Intelligente Ladelösungen für E-Fahrzeuge
• JUICE WORLD | everything about charging electric cars
• Intelligente Ladelösungen für E-Fahrzeuge - Juice World
• technology.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>