Chroma-Q CHSPFV Space Force User Guide

: June 6, 2024
: Chroma-Q

Table of Contents

Chroma-Q CHSPFV Space Force
Installation Procedure
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Chroma-Q CHSPFV Space Force

CHSPFV Space Force Items in the Kit: Space Force Offset Yoke (650-9010 / 647-9015 / 1512-9020)

Items	Part Number	Qty.
Offset Yoke	650-0055 or 647-0087

or 1512-0048

| 1
Adjustable Handle for Offset Yoke| 900-0672| 1
Thrust/ Surface Bearing 12mm ID, 26mm OD, 9mm thick (set of 3)| 900-0614| 1
Friction Disc 12mm ID, 63mm OD| 900-0613| 1
Bolt M12x25 Hex Head Blk| 412-1925-0| 1
Washer Spring 12mm ID| 412-2822-0| 2
Bushing Flanged 12mm ID, 25mm Blk| 412-5012-0| 1
Friction Disc 16mm ID, 63mm OD| 900-0595| 1
Spigot for Yoke| 900-0621| 1
Knob M10x1.5 – 20mm| 648-0113| 1
Screw M12X40 SHSC Blk| 412-1440-0| 1
Washer Flat 1/2″| 350-2114-4| 1
Yoke Bracket M12 Blk | 650-0035| 2
Screw M4x8 FH Phillips Blk| 440-1108-0| 8

Available in only 650-9010 Kit, not included in 647-9015 or 1512-9020 kit. The Space Force onebytwo and Space Force twobyfour light fixture have the brackets factory installed. The P/N of Brackets installed on Space Force onebytwo and Space Force twobyfour are 647-0090 and 1512-0040 respectively. components

Tools Required

Screwdriver PZ1 x 80mm for the Side Bracket screws (Minimum torque: 5.5 in-lb.)
19 mm (or adjustable) wrench/spanner
10 mm Allen key

Installation Procedure

For Space Force (Octagon): Install the Yoke Brackets (650-0035) on both sides of space force unit using PZ1 x 80mm screw driver. Tighten the screws (440-1108-0) to make a solid connection. For Space Force onebytwo and Space Force twobyfour the two brackets are already mounted on the fixture.
On the yoke arm with the 12mm hole, place the Friction Disc (900-0613) in between the Yoke (650-0055 / 647-0087 / 1512-0040) and the Yoke Bracket (650-0035 / 647-0090 / 1512-0048). Place the Friction Disc in parallel to the Yoke Bracket aligning the holes and then place the Yoke. Place the Thrust Bearing set (900-0614) on outer side of the Yoke, and then install the Adjustable Handle (900-0672). Press and spin clockwise the Adjustable Handle to allow the threaded screw to go into the threaded hole of the Yoke Bracket. Rotate until the joint is tightened.
On the yoke arm with the16 mm diameter hole, place the Friction Disc (900-0595) in between Yoke Bracket and the Yoke, then slide the Bushing Flanged 12mm BLK (412-5012-0) in slot, insert the M12X25 Bolt (412-1925-0) with the Flat Washer 12mm (412-2124-0) between Bushing and Bolt using a wrench. Tighten the Bolt completely to make a solid connection.
Attach the Spigot to the Yoke using the M12X40 SHSC Screw, placing the ½” washer and 12 mm spring washer in between. Use appropriate Allen key to tighten the M12X40 Screw to make a solid connection. Attach the Knob (641-0113) to the spigot.

Diagrams

Disclaimer
Dimensions and illustrative drawings contained herein are accurate to the company’s knowledge at the time of printing, however, specifications are subject to change without notice.
Further Information
Please refer to the Chroma-Q Space ForceTM, Space ForceTM onebytwo or Space ForceTM twobyfour manual for more detailed information.
A copy of the manual can be found at the Chroma-Q website – https://chromaq.com/support/downloads

The information contained herein is offered in good faith and is believed to be accurate. However, because conditions and methods of use of our products are beyond our control, this information should not be used in substitution for customer’s tests to ensure that Chroma-Q products are safe, effective, and fully satisfactory for the intended end-use. Suggestions of use shall not be taken as inducements to infringe any patent. Chroma-Q sole warranty is that the product will meet the Chroma-Q sales specifications in effect at the time of shipment. Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown to be other than as warranted. Chroma-Q reserves the right to change or make alterations to devices and their functionality without notice due to ongoing research and development.

The Chroma-Q Space Force has been designed specifically for the lighting industry. Regular maintenance should be performed to ensure that the products perform well in the entertainment environment. If you experience any difficulties with any Chroma-Q products please contact your selling dealer. If your selling dealer is unable to help please contact support@chroma-q.com. If the selling dealer is unable to satisfy your servicing needs, please contact the following for full factory service:

Outside North America:
Tel: +44 (0)1494 446000
Fax: +44 (0)1494 461024
support@chroma-q.com

North America:
Tel: +1 416-255-9494
Fax: +1 416-255-3514
support@chroma-q.com

For further information please visit the Chroma-Q website at www.chroma.com. Chroma-Q is a trademark, for more information on this visit www.chroma-q.com/trademarks.
The rights and ownership of all trademarks are recognized.