MAREA B59003 Smart Watch User Manual
- June 6, 2024
- MAREA
Table of Contents
B59003
User Manual
Please refer to this
manual before using the product.
Cautions before using
- The company reserves the right to modify the contents of this manual without any further notification. It is normal that some functions may vary in certain versions of software.
- Please charge this product with the charger provided for no less than 2 hours before using it for the first time.
- In the APP, set personal information to sync time before using the smartwatch. Please refer to the instructions about synchronization for details.
- The watch has IP68 waterproof rating. It cannot be used in corrosive liquids or hot water, tea, etc. It is not compatible with deep-sea diving of more than 3 meters. All the above situations will cause damage to the smartwatch (these damages will not be covered by the warranty).
Product overview
Models
can be paired with:
- Android phone: supports OS 5.0 and above
- Iphone: supports OS 9.0 and above
APP download and connection
2.1 Please scan the QR code below to download APP
It is recommended to use a browser to scan and download the app. Please give
the corresponding permissions in the download and installation process to
ensure a good Bluetooth connection. The APP name is “LinkTo Sport”.
QR code to download
LinkTo Sport
|
---|---
http://api.start.king-wear.top/link-to/sports-app-download| LinkTo Sport app
icon
Notes:
- For Apple phone users: If it is in standby or hibernation state for a long time (for example, for 2 hours or more, the phone has not been used and it is in a black screen state), LinkTo Sport will be cleaned up by the iOS system, so the APP and the watch will disconnect and the functions on the APP will not be available. Please re-open it and they will automatically reconnect.
- For Android phone users: After installing the APP on the phone, you need to enable the background application launch permission in the settings of your phone. Each smartphone is different. Take a Huawei phone as an example. The steps are as follows: Settings–Application–Application Launch Management—LinkTo Sport, find the application, change the automatic management to manual management, open all permissions (allow Autolaunch,
Secondary launch, Run in the background). This is only for the application to maintain the Bluetooth connection with the watch while the phone is in standby mode (the phone does not have a bright screen). This permission will not use network traffic, nor does it affect the power consumption of the phone.
2.2 Link APP and smartwatch
2.2.1 Open the application, choose “Register” or “Login without registering”.
2.2.2 For Android users: click on “Pair new device” and select the model that
corresponds with your smartwatch. Then the QR code scanner will open.
2.2.3 Open the QR code on the watch and scan it to link the watch. It will
take about 30 seconds to connect properly after scanning. Confirm all
permission requests that appear automatically to ensure that all functions
work correctly.
2.2.4 For iPhone users: The request to “pair new device” will appear on your
phone after scanning.
2.2.5 If the QR code scan fails, select the manual connection function to
complete the pairing via Bluetooth.
2.3 APP settings (functions are available only if watch and phone have been paired successfully)
- Call notification: Tap to turn on/off this function. If turned on, you can hang up the incoming call on your watch.
- Social media notifications: Tap to turn on/off and choose which apps’ notifications you want to receive on your watch.
- Alarm clock (up to 5 alarms)
- Sedentary reminder: Tap to turn on/off. Set starting time, end time, interval, and threshold.
- Drink water reminder: Tap to turn on/off. Set starting time, end time, interval, and threshold.
- DND mode (Do not disturb mode): Tap to turn on/off. Set starting time and end time. Note: when turned on, the watch will not receive notifications.
- Turn on-screen when turning wrist: Tap to turn on/off.
- Heart rate monitoring: Tap to turn on/off. Set starting time, end time, and interval. If turned on, the watch will automatically monitor heart rate, and sync data to APP.
- Remote camera control (on some phones it may be necessary to turn on the camera manually on the phone)
- Find device: Upon tap, the watch will pop up a watch icon and vibrate.
- Firmware update (make sure there is at least 50% battery before updating, keep your watch near your phone during the update)
- Device version: To check the firmware version of the watch.
- Unbound (iPhone users must enter phone settings, enter Bluetooth settings and ignore the device to make sure the device is completely disconnected)
Main functions
3.1 Basic Operation
3.1.1 Power on Long press the button for 3 seconds to turn on the watch, short
press the button to light up the watch if it is in standby mode.
3.1.2 Power off if the screen is on, long-press the button for 3 seconds to
turn the watch off.
3.1.3 Watch interface shift process:
- Slide from top to bottom on the main screen dial to see the status bar, which includes DND mode, brightness level, settings, connection icon, and battery.
- Slide from right to left on the main screen to enter the menu.
- Slide from left to right on the main screen to see the messages received.
- Slide from bottom to top on the main screen to see the health and sleep data.
3.2 Main screen selection
Long press the screen for 3 seconds to display all the options to choose from,
slide left and right to choose the preferred main screen. Single touch to set
it as the default main screen.
3.3 Notifications (messages)
After you have successfully paired your phone and activated the notifications
in the app, the messages received on the phone will be synchronized with the
watch. The watch saves the last 8 messages and they can be deleted by sliding
up and clicking on the trash can icon.
Note : the received messages can be read on the smartwatch, but they
cannot be answered from the watch and audios cannot be played.
3.4 Pedometer
The watch automatically records steps, distance, and calories whenever the
watch is on. To see the data from the pedometer: swipe up from the watch’s
main screen or swipe left from the main screen to access the menu.
3.5 Sport mode
3.5.1 Sport mode includes outdoor walking, indoor walking, outdoor running,
indoor running, cycling, hiking, and swimming.
3.5.2 Click the icon to enter the corresponding sport mode and customize the
goal of the day (distance, time, or calories) or set no goals. The smartwatch
will automatically save the setting and will apply it the next time that sport
mode is used.
Note : The data will only be saved when the exercise time is more than 5
minutes or more than 200 steps. Either one of those conditions will activate
the recording function, otherwise, the recording function will fail due to
insufficient data. 3.5.3 When you start recording the data, the watch screen
will display the following content: type of sport and start time. You can
swipe up and down to see detailed records. The data will vary according to the
type of sport.
3.5.4 Goal completion : The smartwatch will display ‘Goal completed’ when
the preset goal is accomplished. Moreover, the record function will keep
recording if the exercise continues.
3.6 Health
3.6.1 Heart rate : The display will show “–Bpm”. Two seconds later the
heart rate test begins. The data will be displayed on the watch screen when
the heart rate data is detected and the detection will be carried out
continuously. If you want to stop the detection, swipe right to exit and
return to the previous screen. In the app, you can check the historical data,
including the highest and average data from the last test. 3.6.2 Blood
pressure: The display will show “–mmHg”. Two seconds later the blood pressure
test begins. The data will be displayed on the watch screen when the blood
pressure data is detected and the detection will be performed continuously. If
you want to stop the detection, swipe right to exit and return to the previous
screen.
Note : All heart rate and blood pressure tests will take about 10-30
seconds to generate data.
3.7 Pairing with QR code
In the application, select “Pair new device” to scan the QR code of the watch
and thus link with the phone. The “connection” icon in the watch’s drop-down
menu will appear blue if the watch is connected. Each watch can only be
connected to one phone. 3.8 Training records The last 8 training records can
be displayed. The records will be displayed in chronological order and can be
viewed by sliding up and down.
3.9 Sleep Monitor
The default sleep monitor starts at 21:00 pm and ends at 7:30 am the next day.
If the watch is worn while sleeping, you can check the sleep time on the watch
the following morning. If the smartwatch is paired with the phone, the sleep
data will be synchronized automatically (or manually) with the application.
Note : The smartwatch is able to automatically identify the sleeping status. There may be differences between the detected data and the actual data because the watch may still be under the detection process. The watch will display the detected result of the whole night, which will be identical to the actual sleep data, once it finishes the monitoring. There may be some deviation from the actual sleeping status due to the change in different sleep modes.
3.10 Remote music player
3.10.1 If the watch has not been paired with your phone, an ‘unconnected’
message will pop up when you click the ‘Music’ icon, and it will automatically
exit without any actions after 2 seconds.
3.10.2 After pairing the watch with your phone, you can enter the music player
function of the watch to control the phone’s music player. There may be some
compatibility problems due to the variety of music players. Usually, the watch
can control your phone’s music player directly, but some players may need to
be opened manually before been remotely controlled by the watch.
3.10.3 The watch can pause, play and switch to the previous or next song, but
it does not show the name of the song and cannot adjust the volume.
3.11 Alarm clock (only set via APP)
The application supports setting a maximum of 5 alarms. Upon entering the
“Alarm” function, the display will show 2 alarms, swipe up to see more alarms,
if any.
3.12 Timer
Set target time, then click the start icon. The message “timed out” will pop
up on the screen and the watch will vibrate.
3.13 Stopwatch
Click the star icon to start counting. Click the green icon to stop, click the
blue icon to set a lap time. If the counting is stopped, the blue icon will
change to red, if the red icon is clicked, the counting will stop and all
records will be cleared. The watch keeps records of up to 20 lap times. Swipe
up or down to see more lap times
3.14 Find phone
If the watch is paired with the phone, when you click “Find phone” on the
watch, the phone will vibrate and ring.
3.15 Settings
Screen brightness setting: there are 3 levels of brightness, click the screen
to adjust it. Backlight time: choose the time it takes to turn the screen off
(max 95 seconds, min 5 seconds).
Remote camera control: if the watch is paired with the phone when you click on
the camera function on the watch, a camera icon will appear on the watch and
the phone’s camera will open. If you click on the camera icon on the watch, it
will take a photo on the phone and be automatically saved in the phone’s photo
album. On some phones, it will be necessary to open the camera manually before
using this function.
QR code to download the app: you can use your phone to scan this QR code in
order to download the latest version of the app.
Reset: tap the left icon to exit, and tap the right icon to reset. Then all
data of the watch would be cleared. Note: the data of the paired phone will
not be cleared unless the phone is also reset. About: you can see the Mac
address of the device, the Bluetooth name, and the firmware version.
Precautions
4.1 Only one smartwatch pairing application should be installed on the phone
to ensure that the connection with the smartwatch is normal. If several
applications are connected, they can affect the connection between the watch
and the phone.
Note : Some Android phones will prompt you that you cannot install them.
Please go to ‘settings of the phone and authorize the ‘Unknown source’.
4.2 When the mobile phone requests permissions, click “Allow”. On the
contrary, you may not receive notifications, scan QR codes, open the remote
camera or use other functions. These permissions do not affect the flow of the
phone or other information on the phone. 4.3 Some Android phones may
accidentally close the app when cleaning the applications. Please keep the app
running in the background. Android phone settings (background running method):
open the phone settings – application management – LinkTo Sport – Rights
management – Backstage management – select background running. (The setting
method may be different due to different mobile phone versions and models).
4.4 Heart rate monitoring requires that the watch and arm are in contact, and
the watch should not be too tight or too loose. The test may be inaccurate if
it is too tight because it will affect blood flow, and if it is too loose
because it will affect heart rate sensor monitoring. 4.5 Avoid hitting the
smartwatch, it could break the glass. 4.6 Use 5V, 1A for charging. This
product does not support fast charging. Do not charge if the watch has water
(or sweat) to avoid short circuits and damaging the product. 4.7 This product
is an electronic monitoring product, not for medical reference.
Troubleshooting
In case there is a problem when using the smartwatch, please solve it according to the following steps. If the problem is not solved, please contact the seller or designated maintenance personnel.
5.1 The watch cannot be turned on:
5.1.1 Press the display touch area for over 3 seconds.
5.1.2 Make sure there is enough battery. Battery power may be too low, please
charge it.
5.1.3 If the smartwatch has not been used for a long time and the normal
charger does not respond, please try charging it with an output power of
5V/1A.
5.2 It shuts down automatically:
5.2.1 Battery power may be too low, please charge it.
5.3 Short battery life:
5.3.1 It may occur when the battery has not been fully charged, please ensure
the is enough time for charging (at least 2 hours is required).
5.3.2 Charger or data cable may not work properly, please change to new ones.
5.3.3 Please check the port of the data cable and try again to ensure a proper
connection.
5.4 Bluetooth disconnects or unable to connect:
5.4.1 Please restart it.
5.4.2 Please turn off the Bluetooth of the mobile phone and open it to
reconnect.
5.5 Inaccurate sleep data:
The sleep monitor is designed to mimic the natural pattern of falling asleep and waking up. Please use the smartwatch during the day, otherwise, a deviation may occur if you go to bed late or only use it while you sleep. Sleep data may not be generated if you go to bed during the day, since the default sleep time is set between 9:00 p.m. and 7:30 a.m.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>