HH ELECTRONICS TNi-C4 Ceiling Loudspeaker User Manual
- June 6, 2024
- HH Electronics
Table of Contents
CEILING LOUDSPEAKERS
USER MANUAL
CEILING INSTALLATION LOUDSPEAKER iNSTALL
The Tessen TNi-C range delivers premium audio reinforcement.
Designed with the audio installer in mind, the TNi-C range features high-grade coaxial drivers and 4 position power tap selector located under the front steel grille; providing swift output adjustment once the ceiling speaker is installed.
With connectivity for 70V/100V and 8 Ohm low impedance lines, the TNi-C range delivers a highly flexible solution. The spring connection terminals ensure cables are secure once fitted and the dog ear mounts are a simple yet effective mounting method.
INSTALLATION GUIDE
Adjustable Power Modes
can be accessed after installation with the quick switch options.
Quick-Lock Mounting
Rotating locking lugs for secure rattle-free mounting.
-
Choose a suitable location for the installation. Rear clearance and the structural integrity of the mounting surface must be considered and anything else such as piping and cable that may have previously been installed.
2A: Grill removal: Set one of the Mounting Arms (Out Position) as shown (A).
2B: Gently push the Mounting Arm in the direction shown.
2C: The speaker Grill Should lift allowing it to be easily removed. -
: Audio connection: Ensure correct polarity, especially if a 70V/100V line system is used.
-
: Carefully position the Ceiling Speaker in the ceiling aperture after ensuring the mounting arms are set as shown.
5A: Fix the speaker to the ceiling in place using three fixing screws for the TNi-C4 and four for the TNi-C6 and TNi-C8.
5B: Power Mode. Set the output wattage and voltage line based on the connection setup. See pages 3 and 4 for more information. -
: To complete the install, carefully fit the speaker grille.
Power Modes: Depending on the required output level, and the type of amplifier used to power the system, connect see. These are summarized below:
OPTION 1: 70V LINE SYSTEM
Audio connection and audio tap setup.
OPTION 2: 100V LINE SYSTEM
Audio connection and audio tap setup.
70V/100V line systems have the added advantage of allowing many speakers to be
used in the setup using parallel connections. Ensure the cable used is capable
of delivering the working current and the amplifier has sufficient drive
capacity to support the number of speakers in the system.
OPTION 3: LOW IMPEDANCE SETUP
For added flexibility, the TNi-C Range provides a Low impedance setting for use with a conventional amplifier.
For a Low Impedance
setup, ensure the + speaker cable IS NOT connected to the 70V/100V output.
Doing so could result in damage to the Ceiling Speaker.
Depending on the amplifier used, it may be possible to use more than one
loudspeaker in this mode.
LOW IMPEDANCE – PARALLEL CONNECTION – The amplifier will see a combined
speaker impedance of 4Ω.
LOW IMPEDANCE – SERIES CONNECTION – The amplifier will see a combined
speaker impedance of 16Ω.
SPECIFICATION – TNi-C4
Model
Woofer Size
Woofer Cone Material
Tweeter Size
100V Transformer Power Taps
70V Transformer Power Taps
Low Impedance 1
System Power Rating
Recommended Amplifier 2
Sensitivity 1W/1m 3
Max SPL 1m
Frequency Response
Input Connector 4
Nominal Coverage| TNi-C4
4 inch
Paper
1.5-inch Neodymium
30W, 15W, 6W
15W, 7.5W, 3W
8 ohm
45W AES, 180W Peak
80-160W @ 8 Ohms
88 db SPL
111 dB SPL
85Hz – 20KHz (-10dB)
100Hz – 16KHz (-3dB)
Push Spring Connectors
130° conical
---|---
Enclosure
Outside Diameter
Depth
Cutout
Installation Grip Range
Main Construction Material
Grille Main Material
Finish
Mounting Points
Unit weight
Single Carton dimensions (HWD)
Single Packed weight
EAN Code
Master Carton Dimensions (HWD)
Master Packed weight
Master EAN Code| 204mm, (8″)
156mm, (6.1″)
180mm, (7.1″)
4-20mm
ABS Plastic
1.5mm Circular Mesh Steel
White
3x Dog Ear Brackets
1.4Kg, 3.1 lbs
180 x 205 x 205mm, (7.1″ x 8.1″ x 8.1″)
1.9Kg, 4.2 lbs
5060109457032
400 x 450 x 450mm, (15.7″ x 17.7″ x 17.7″) (8pcs)
16.2Kg, 35.7 lbs
5060109457049
---|---
In the interest of continuous development, HH reserves the right to amend
product specifications without prior notification.
For polar plots, EASE modeling files, 2D and 3D drawings files, please check www.hhelectronics.com
- AES standard Pink Noise 12dB crest factor 2 hours.
- Measured in Full space (4π) conditions
- Calculated maximum SPL based on rated power handling
- Average coverage between 500Hz – 4KHz
SPECIFICATION – TNi-C6
Specifications
Model
Woofer Size
Woofer Cone Material
Tweeter Size
100V Transformer Power Taps
70V Transformer Power Taps
Low Impedance 1
Power Rating
Recommended Amplifier 2
Sensitivity 1W/1m 3
Max SPL 1m
Frequency Response
Input Connector 4
Nominal Coverage| TNi-C6
6.5 inch
Paper
1.5-inch Neodymium
40W, 20W, 10W
20W, 10W, 5W
8 ohm
55W AES, 220W Peak
100-200W @ 8 Ohms
90 dB SPL
113 dB SPL
75Hz – 20KHz (-10dB)
85Hz – 16KHz (-3dB)
Push Spring Connectors
120° conical
---|---
Enclosure
Outside Diameter
Depth
Cutout
Installation Grip Range
Main Construction Material
Grille Main Material
Finish
Mounting Points
Unit weight
Single Carton dimensions (HWD)
Single Packed weight
EAN Code
Master Carton Dimensions (HWD)
Master Packed weight
Master EAN Code| 260mm, (10.2″)
176mm, (6.9″)
235mm, (9.3″)
4-20mm
ABS Plastic
1.5mm Circular Mesh Steel
White
4x Dog Ear Brackets
2.1Kg, 4.6 lbs
200 x 260 x 260mm, (7.9″ x 10.2″ x 10.2″)
2.7Kg, 6 lbs
5060109457032
440 x 560 x 560mm, (17.3″ x 22″ x 22″) (8pcs)
23Kg, 50.7 lbs
5060109457049
---|---
In the interest of continuous development, HH reserves the right to amend
product specifications without prior notification.
For polar plots, EASE modeling files, 2D and 3D drawings files, please check www.hhelectronics.com
- AES standard Pink Noise 12dB crest factor 2 hours.
- Measured in Full space (4π) conditions
- Calculated maximum SPL based on rated power handling
- Average coverage between 500Hz – 4KHz
SPECIFICATION – TNi-C8
Specifications
Model
Woofer Size
Woofer Cone Material
Tweeter Size
100V Transformer Power Taps
70V Transformer Power Taps
Low Impedance 1
Power Rating
Recommended Amplifier 2
Sensitivity 1W/1m 3
Max SPL 1m
Frequency Response
Input Connector 4
Nominal Coverage| TNi-C8
8 inch
Paper
1.5 inch Neodymium
40W, 20W, 10W
20W, 10W, 5W
8 ohm
65W AES, 260W Peak
100-200W @ 8 Ohms
91 db SPL
115 dB SPL
65Hz – 20KHz (-10dB)
80Hz – 16KHz (-3dB)
Push Spring Connectors
100° conical
---|---
Enclosure
Outside Diameter
Depth
Cutout
Installation Grip Range
Main Construction Material
Grille Main Material
Finish
Mounting Points
Unit weight
Single Carton dimensions (HWD)
Single Packed weight
EAN Code
Master Carton dimensions (HWD)
Master Packed weight
Master EAN Code| 300mm, (11.8″)
195mm, (7.7″)
275mm, (10.8″)
4-20mm
ABS Plastic
1.5mm Circular Mesh Steel
White
4x Dog Ear Brackets
2.6Kg, 5.7 lbs
220 x 300 x 300mm, (8.7″ x 11.8″ x 11.8″)
3.3Kg, 7.3 lbs
5060109457070
480 x 640 x 640mm, (18.9″ x 25.2″ x 25.2″) (8pcs)
28Kg, 61.7 lbs
5060109457087
---|---
In the interest of continuous development, HH reserves the right to amend
product specifications without prior notification.
For polar plots, EASE modeling files, 2D and 3D drawings files, please check www.hhelectronics.com
- AES standard Pink Noise 12dB crest factor 2 hours.
- Measured in Full space (4π) conditions
- Calculated maximum SPL based on rated power handling
- Average coverage between 500Hz – 4KHz
Designed and Engineered in the UK by HH Electronics LTD.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>