HH ELECTRONICS VRE-12G2 Full Range Passive Loudspeaker User Manual
- June 6, 2024
- HH Electronics
Table of Contents
HH ELECTRONICS VRE-12G2 Full Range Passive Loudspeaker User Manual
Thank you for purchasing a HH Vector Passive Full Range Enclosure. The Vector series are professional specification cabinets designed to give exceptional dynamics, clarity and projection in all applications such as a portable PA. In order to take full advantage of it and enjoy long and trouble-free performance, please read this owner’s manual carefully, and keep it in a safe place for future reference.
- Read Instructions carefully before installing or operating this product.
- Retain these instructions
- Comply with warnings: All warnings and instructions for these products should be adhered to.
- Unpacking: Please retain the packing carton and liners in case the unit should need to be returned at any time.
- Amplifier connection. In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your sound system. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. BEFORE turning on your power amplifier. Many products have large transient surges at turn on and off which can cause damage to your speakers. By turning on your power amplifier LAST and making sure its level control are set to minimum any transients from other equipment will not reach your loudspeakers. Wait until all system parts have stabilized. This can usually take a couple of seconds. Similarly, when turning off your system always turn down the level controls on your power amplifier and then turn off its power before turning off other equipment.
- Cables- never use a shielded or microphone cable for any speaker connections as this will not be substantial enough to handle the amplifier load and could cause damage to your complete system.
- Caution: These professional loudspeaker systems are capable of generating very high sound pressure levels. Use care with placement and operation to avoid exposure to excessive levels that can cause permanent hearing damage.
- Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel.
BASIC SETUP
HH VRE cabs can be mounted on the floor, or a suitable pole or tripod. Don’t
over-extend poles/tripods; ensure at least 4 x the pole diameter is still
inside the outer pole. Make sure the legs have a good splay on tripods, but do
not obstruct doorways or other access-ways.
SPECIFICATION
IMPORTANT SAFETY INSTRUCTIONS
GENERAL INSTRUCTIONS
In order to take full advantage of your new product and enjoy long and
trouble-free performance, please read this owner’s manual carefully, and keep
it in a safe place for future reference.
- Unpacking: On unpacking your product please check carefully for any signs of damage that may have occurred whilst in transit from the HH factory to your dealer. In the unlikely event that there has been damage. please re-pack your unit in its original carton and consult your dealer. We strongly advise you to keep your original transit carton, since in the unlikely event that your unit should develop a fault, you will be able to return it to you dealer for rectification securely packed.
- Amplifier Connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your system. Wroth all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc., BEFORE turning on your amplifier. Many products have large transient surges at turn on and off which can cause damage to your SJ>eskers. By turning on your bass amplifier LAST and making sure its level control is set to a minimum, any transients from other equipment should not reach your loud speakers. Wait till all system parts have stabilized, usual a couple of seconds. Similarly when turning off your system always turn down the level controls on your bass amplifier and then turn off its power before turning off other equipment
- Cables: Never use shielded or microphone cable for any speaker connections as this will not be substantial enough to handle the amplifier load and could cause damage to your complete system.
- Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel.
FCC COMPUANCY STATEMENT
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
I) This device may not cause harmful interference
2) This device must accept any interference received, that may cause undesired
operation.
Warning: Changes or modification to the equipment not approved by HH Electronics Ltd. can void the user’s authority to use the equipment.
Note: This equipment has been tested and found to comply with the limits
for Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try and correct
the interference by one or more of the following measures. Reorient or
relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
This product conforms to the requirements of the following European
Regulations, Directives & Rules;
CE Mark (93/68/EEC), Low Voltage 2014/35/EU, EMC (2014/30/EU), Ro HS
(2011/65/EU), RED (2014/30/EU), ERP 2009/125/EU
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, HH Electronics Ltd. declares that the radio equipment is in compliance with Directives 2014/53/EU, 2011/65/EU, 2009/125/EU
Full text of the EU declaration of conformity is available at the following internet address:
http://support.hhelectronics.com/approvals
In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with A normal household waste to landfill sites. It must be taken to an approved recycling center according to the recommendations of the WEEE (Waste Electrical and Electronic Equipment) directive applicable in your country.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Headstock Distribution Ltd is under license. Other trademarks and trade names are those of their respective owners. HH-Electronics Ltd. is a registered trademark of Headstock Distribution Ltd.
INCORPORATED RADIO EQUIPMENT DEVICE TECHNICAL SPECIFICATION:
Frequency Range: 2402-2480MHz
Transmit Power: +Sebum (6.3mW)
Receiver Sensitivity: -91 dBm
Operating Protocol: Bluetooth Class 2
WARNING: When using electrical products, basic cautions should always be followed, including the following:
-
Read these instructions.
-
Keep these instructions safe.
-
Heed all warnings.
-
Follow all instructions.
-
Do not use this apparatus near water.
-
Clean only with a dry cloth.
-
Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.
-
Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
-
An apparatus with Class I construction shall be connected to a mains socket outlet with a protective connection. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
-
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the apparatus.
-
Only use attachments/accessories provided by the manufacturer.
-
Use only with a cart. stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
-
The mains plug or appliance coupler is used as the disconnect device and shall remain readily operable. The user should allow easy access to any mains plug, mains coupler and mains switch used in conjunction with this unit thus making it readily operable. Unplug this apparatus during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
-
Never break off the ground pin. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.
-
If this product is to be mounted in an equipment rack, rear support should be provided.
-
Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your plug. proceed as follows:
a) The wire that is cultured green and yellow must be connected to the terminal that is marked by the letter E, the earth symbol, cultured green or cultured green and yellow.
b) The wire that is cultured blue must be connected to the terminal that is marked with the letter N or the color black
c) The wire that is cultured brown must be connected to the terminal that is marked with the letter Lord the color red. -
This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objects containing liquids, such as vases, upon the apparatus.
-
Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Earplugs or protectors to the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.
-
Symbols & nomenclature used on the product and in the where extra caution may be necessary, are as follows;
Intended to alert the user to the presence of high ‘Dangerous Voltage’ within the products enclosure that may be sufficient to constitute a risk of electrical shock to persons.
Intended to alert the user of the presence of important operating and maintenance (Servicing) instructions in the literature accompanying the product.
Risk of electrical shock – DO NOT OPEN. To reduce the risk of electrical shock, do not remove the cover. No user serviceable parts inside. Refer servicing to qualified personnel.
To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture. Before using this appliance please read the operating instructions.
If your appliance features a tilting mechanism or a kickback style cabinet, please use this design feature with caution. Due to the ease with which the amplifier can be moved between straight and tilted back positions, only use the amplifier on a level, stable surface. DO NOT operate the amplifier on a desk, table, shelf or otherwise unsuitable non-stable platform.
Model number:__
Serial number:__
Place of purchase:__
Date of purchase:__
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>