GLIDEAWAY CB1810RF-K MICA Adjustable Base Owner’s Manual
- June 6, 2024
- GLIDEAWAY
Table of Contents
GLIDEAWAY CB1810RF-K MICA Adjustable Base Owner's Manual
User Info
Please take a moment and write down the serial number in the space provided
below, in case you need to refer to it in the future. This information can be
found by raising the head section of the bed.
SKU: CB1810RF
Serial Number ____
This number will be required for future service claims.
SAFETY INFORMATION
ATTENTION! IMPORTANT SAFETY INSTRUCTIONS. SAVE THIS MANUAL! PLEASE READ
THESE INSTRUCTIONS THOROUGHLY BEFORE USING THIS PRODUCT. PROPER OPERATION OF
YOUR ADJUSTABLE BED IS NECESSARY
TO ENSURE THE LONG LIFE AND DURABILITY YOU EXPECT FROM A HIGH-QUALITY
PRODUCT. THE MANUFACTURER HAS TESTED AND INSPECTED THIS PRODUCT PRIOR TO
SHIPMENT.
RADIO FREQUENCY IS 2.4Ghz.
This device complies with part 15 of the FCC Rules and Industry Canada’s
license exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation of the device.
Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void the user’s right to operate the device. The input voltage is AC100-240 50/60HZ; the output voltage is DC29V 1.8A.
ELECTRICAL SAFETY
Always unplug this adjustable bed from the electrical outlet before any
cleaning or maintenance of the adjustable bed. To safely disconnect, remove
the plug from the outlet. Keep cord away from heated surfaces. Use only
indoors.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO
MOISTURE.
Discontinue use of this adjustable bed and contact the manufacturer for repair
if: (1) it has a damaged cord or plug, (2) it is not working properly, or (3)
it has been dropped or damaged.
FOR OPTIMAL SAFETY, YOUR ADJUSTABLE BED SHOULD BE PLUGGED INTO A SURGE PROTECTOR (not supplied with this adjustable bed).
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
- Warning Danger of explosion if battery is incorrectly replaced. Replace only with the 6LR61 9V batteries and LR03 AAA batteries.
- Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. A reversed battery may cause damage to the device.
- Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and Carbon-zinc) or old batteries with fresh ones.
- If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
- Do not try to recharge a battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s directions.) 2
WARRANTY WARNING!
This bed is specifically designed to require no maintenance by you, the user.
Any opening or tampering with the control box, motors or hand controls (with
the exception of the battery compartment, if equipped) will void the warranty.
Do not attempt to alter component wiring or adjust or modify the structure of
the product in any way or the warranty will be void. Only those authorized may
conduct repairs or part replacement on your adjustable bed.
IN-HOME USE ONLY
This adjustable bed is designed exclusively for in-home use.
HOSPITAL/MEDICAL DISCLAIMER: This base is NOT designed for hospital or medical use (In-Home or Commercial) and is NOT designed to meet medical or hospital standards. Do not use this base with TENT TYPE oxygen therapy equipment or use near explosive gases.
PRODUCT RATINGS
Lift Motor Restrictions: The lift motors in this bed are NOT designed to
operate continuously for more than one (1) minute over an eight (8) minute
time period, or approximately 12% duty cycle. To ensure reliable functionality
and full life of this product, do not attempt to exceed these limits.
NOTE: Attempting to circumvent or exceed this rating will shorten the
life expectancy of the product and may void the warranty.
Weight Restrictions: The recommended weight limits on our adjustable beds
are: Queen: 600 lbs.
Full/XL: 500 lbs.
Twin/XL: 400 lbs. (800 lbs. if using two twins as a King)
1/pc King: 800 lbs.
The structure of the bed will support the recommended weight when distributed
evenly across the bed.
The head and foot sections are not designed to individually support or lift
this amount of weight.
For optimal performance and integrity of structure, entering and exiting the
adjustable bed with the bed in the flat position is recommended.
NOTE: Exceeding the recommended weight restrictions could damage your
adjustable bed and void your warranty.
SMALL CHILDREN AND PETS WARNING
Immediately dispose of all packing materials as they can pose a smothering
risk to small children and pets. Injury could also occur if children or pets
are permitted to play on or under the bed. Do not allow children to operate
this bed without adult supervision.
LUBRICATION AND CLEANING
This product is designed to be maintenance-free. The lift motors are
permanently lubricated and sealed — no additional lubrication is required. Do
not apply lubricant to lift motor lead screws or any nylon nuts or the base
may inadvertently creep downward from the elevated position.
LIFT WARNING
DO NOT SIT ON THE HEAD OR FOOT SECTIONS WHILE IN THE RAISED POSITION, OR
DURING LIFT OR LOWERING CYCLES.
MOVING AFTER INSTALLATION
Do not place adjustable bed base vertically on its head or foot sections. This
may cause injury to persons or damage to base.
WARNING!
To reduce the risk of burns, fire, electric shock, or injury to persons:
- Unplug from outlet before putting on or taking off accessories.
- Close supervision is necessary when this base is used by, or near children, invalids, disabled persons, or pets.
- Use this base only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this base if it has a damaged cord or plug, is not working properly, has been dropped or damaged, or dropped in water.
- Keep the cord away from heated surfaces.
- Never drop or insert any object into any opening.
- Do not use outdoors.
- Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
- To disconnect, remove plug from outlet.
- DO NOT USE NEAR PEOPLE USING OR WEARING MEDICAL DEVICES. FOR HOUSEHOLD/RESIDENTIAL USE ONLY.
WHAT IS INCLUDED
Before discarding any packing materials, check the adjustable base shipping carton and verify the following items are included:
ASSEMBLY – BASE
It is HIGHLY recommended to use two people for the installation of this product. To assemble, please perform the following steps:
-
Carefully lift both Base Pieces from the shipping carton, keeping the unit’s topside down. Remove the plastic wrapping from the bottom to access the bases.
-
Insert the Connecting Rods into one of the Base Pieces and then slide the other Base Piece onto the Connecting Rods as shown.
-
Secure the Base Pieces to each other using the eight hex bolts (four hex bolts for each Connecting Rod) making sure to hand tighten each and then tighten 1/4 turn more, as over-tightening could cause damage to the frame or Connecting Rod.
For step 4, refer to figure A on page 7.
- Connect the Foot motor connector cable to the Head motor connector cable.
Note: The Head and Foot motors are labeled on the respective motor. When setting up a Split Cal King or two Twin XL beds to form a King, refer to the instructions on page 13 in Part B on how to link your remote.
FIGURE A
Please Refer to diagram when assembling the adjustable bed.
NOTE: Make sure wire connected
to Power Supply is routed UNDER the main metal frame and lifting mechanism.
Routing wires on top of the metal frame are likely to result in damage to the
base which may void the warranty.
- Insert the AC cord into the power supply.
**IMPORTANT: DO NOT PLUG THE BASE INTO THE AC OUTLET YET.
**
- Insert the legs into the threaded holes at each corner of the base and rotate clockwise until tight. There must not be any gap or wobble in the leg in order to avoid risk of injury or damage to the base which may void warranty.
NOTE: KING SIZE bases require use of at least two leg segments. Failure
to use a minimum of two leg segments could result in damage to base and floor
and will void your product’s warranty.
- Insert one end of the DC cord into the power supply. Insert the other end with locking clip into the cable coming from the Head Motor. Lock the connection using the locking clip.
TO LINK REMOTE:
If the remote is not linked, see page 13.
- Remove the Mattress Retainer Bar from the bottom of the base. Finish removing the plastic packaging from the base to orient into final position. Carefully rotate the base on its side, then lift and place on legs. **IMPORTANT: DO NOT LEAN THE BED AGAINST THE INSTALLED LEGS TO TURN OVER.
**
- Insert the Mattress Retainer Bar upright as shown.
- Insert the Retainer Clip securely.
LOCATION OF CONTROLS – REMOTE
OPERATION – MAIN
OPERATION – LINKING THE REMOTE
TROUBLESHOOTING
In the event the Comfort Base’s base fails to operate, investigate the symptoms and possible solutions provided below:
AVAILABLE ACCESSORIES
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>