Shark ZU700 Performance Lift-Away® Upright Vacuum Owner’s Manual

June 6, 2024
Shark

Shark ZU700 Performance Lift-Away® Upright Vacuum -
logo

Shark ZU700 Performance Lift-Away® Upright Vacuum

Performance Lift-Away® Upright Vacuum
ZU700 Series
OWNER’S GUIDE
Self-Cleaning Brushroll Technology

IMPORTANT SAFETY INSTRUCTIONS

FOR HOUSEHOLD USE ONLY • PLEASE READ CAREFULLY BEFORE USE
If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT force into outlet or try to modify to fit.

WARNING
To reduce the risk of fire, electric shock, injury, or property damage:

GENERAL WARNINGS
When using an electrical appliance, basic precautions should always be followed, including the following:

  1. Your vacuum cleaner may consist of a motorized nozzle, wand, hose, and/or vacuum pod. This device contains electrical connections, electrical wiring, and moving parts that potentially present a risk to the user.

  2. Use only identical replacement parts.

  3. Carefully observe and follow the instructions provided below to avoid improper use of the appliance. DO NOT use the vacuum for any purpose other than those described in this manual.

  4. Before use, carefully inspect all parts for any damage. DO NOT use if any parts are damaged.

  5. The use of an extension cord is NOT recommended.

  6. This vacuum cleaner contains no serviceable parts.
    USE WARNINGS

  7. This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children. Keep the appliance and its cord out of reach of children. DO NOT allow the appliance to be used by children. DO NOT allow to be used as a toy. Close supervision is necessary when used near children.

  8. Always turn off the vacuum cleaner before connecting or disconnecting any motorized nozzles or other accessories.

  9. DO NOT handle plug or vacuum cleaner with wet hands.

  10. DO NOT use without filters in place.

  11. Only use Shark® branded filters and accessories. Failure to do so will also void the warranty.

  12. DO NOT damage the power cord:
    a)DO NOT pull or carry a vacuum cleaner by the cord or use the cord as a handle.
    b)DO NOT unplug by pulling on the cord. Grasp the plug, not the cord.
    c)DO NOT run the vacuum cleaner over the power cord, close a door on the cord, pull the cord around sharp corners, or leave the cord near heated surfaces.

  13. DO NOT put any objects into nozzle or accessory openings. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.

  14. DO NOT use if nozzle or accessory airflow is restricted. If the air paths or the motorized floor nozzle become blocked, turn the vacuum cleaner off and unplug it from the electrical outlet. Remove all obstructions before you plug in and turn on the unit again.

  15. Keep nozzle and all vacuum openings away from hair, face, fingers, uncovered feet, or loose clothing.

  16. DO NOT use if the vacuum cleaner is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water.

  17. Use extra care when cleaning on stairs.

  18. DO NOT leave the vacuum cleaner unattended while plugged in.

  19. When powered on, keep the vacuum cleaner moving over the carpet surface at all times to avoid damaging the carpet fibers.

  20. DO NOT place vacuum cleaners on unstable surfaces such as chairs or tables.

  21. Your Shark® vacuum may not be designed to stand up on its own. When taking a break from cleaning, you may need to lean it against furniture or a wall, or lay it flat on the floor. Using the vacuum for an application where the unit lacks stability may result in personal injury.

  22. DO NOT use to pick up:
    a)Liquids
    b)Large objects
    c)Hard or sharp objects (glass, nails, screws, or coins)
    d)Large quantities of dust (drywall dust, fireplace ash, or embers). DO NOT use as an attachment to power tools for dust collection.
    e)Smoking or burning objects (hot coals, cigarette butts, or matches)
    f) Flammable or combustible materials (lighter fluid, gasoline, or kerosene)
    g) Toxic materials (chlorine bleach, ammonia, or drain cleaner)

  23. DO NOT use in the following areas:
    a) Poorly lit areas
    b) Wet or damp surfaces
    c) Outdoor areas
    d) Spaces that are enclosed and may contain explosive or toxic fumes or vapors (lighter fluid, gasoline, kerosene, paint, paint thinners, mothproofing substances, or flammable dust)

  24. Turn off all controls before plugging in or unplugging the vacuum.

  25. Unplug from the electrical outlet when not in use and before any maintenance or cleaning.

  26. Hand washes with water only.
    Washing with cleaning chemicals could damage the unit.

  27. During cleaning or routine maintenance, DO NOT cut anything other than hair, fibers, or string wrapped around the brush roll.

  28. Allow all filters to air-dry completely before replacing in the vacuum to prevent liquid from being drawn into electric parts.

  29. Make sure the dust cup and all filters are in place after routine maintenance.

  30. If provided, secure the power cord around the two cord hooks during storage.

To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plugin anyway.

SAVE THESE INSTRUCTIONS

ASSEMBLY

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
1

ASSEMBLY

  1. Place Motorized Floor Nozzle on the floor and attach Pod, pressing it in until it clicks securely into place.
  2. Insert Wand into the pod, pressing it in until it clicks securely into place.
  3. Insert Handle into the wand, pressing it in until it clicks securely into place.
  4. Connect Hose into the back of the pod, pressing it in until it clicks securely into place.
  5. Insert Hose Clip into the back of the handle until it clicks into place.

IMPORTANT: For proper operation, ensure all connections are securely clicked into place.

2 WAYS TO CLEAN

  1. UPRIGHT
    Power
    Press the Power/Surface Selector button to turn the vacuum on or off.
    Floor Setting
    Slide the Power/Surface Selector button up or down to choose floor type.
    Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
2

  2. LIFT-AWAY® OPERATION
    Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
3

WHOLE-HOME CLEANING **

**

SETTINGS

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
4| Shark ZU700 Performance Lift-Away®
Upright Vacuum - figure 5
---|---
Slide selector to Hard Floor then presses selector button to turn on the power.
NOTE: The brushrolls will not spin unless the wand is reclined.| Slide selector to Carpet, then press selector button to turn on the power. Brushrolls will spin faster.
NOTE: The brushrolls will not spin unless the wand is reclined.

SUCTION CONTROLShark ZU700 Performance Lift-Away® Upright Vacuum -
figure 7

Suction Control Collar offers variable suction based on your needs. Slide to MIN to reduce suction and increase maneuverability on carpets. Slide to MAX to increase suction on bare floors.

BRUSHROLL INDICATOR LIGHTShark ZU700 Performance Lift-Away® Upright
Vacuum - figure 8

WHAT DOES THE BRUSH ROLL INDICATOR LIGHT MEAN?
Solid Green: The brush roll and Soft Roller are spinning and working properly. Solid Red: There is a jam in the brush roll area. Turn off the vacuum and unplug it, then remove any blockages in the nozzle.
Flashing Red: Turn off the vacuum, unplug it, and remove any blockages. Let the vacuum cool down for at least 60 minutes before restarting. See the Troubleshooting section for more information. Solid Green with
Headlights Flashing: The brush roll garage lid is not properly closed. Press down firmly on both sides of the lid until it clicks into place.

NOTE: For deep cleaning per ASTM F 608 (embedded dirt in carpets) please set it to Carpet.
NOTE: For particularly stubborn stuck-on dust messes on hard floors, set to Carpet.

WHOLE-HOME CLEANING

CLEANING MODES

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
6| Shark ZU700 Performance Lift-Away®
Upright Vacuum - figure 9
---|---
To engage brushrolls, turn the power on, then
step on the floor nozzle and tilt the handle back.| Press the Handle Release Latch to detach the handle from the wand.
Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
10| Shark ZU700 Performance Lift-Away®
Upright Vacuum - figure 11
Press the Wand Release button to detach the
wand from the pod.| Detach the wand from the pod, then detach the
handle from the wand (see above). Press the Lift-Away button to detach the pod from the floor nozzle.
Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
12Detach wand from the pod (see above). Press the Lift-Away button to detach the pod from the floor nozzle.

NOTE: All accessories are compatible with both the wand and the handle.

EMPTYING THE DUST CUP

IMPORTANT: Unplug the power cord before performing any maintenance.

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
14

To remove Dust Cup, slide up the buttons on both sides of the handle. Tilt the dust cup, then lift to remove.| To empty debris, press the lower release button, and the bottom of the dust cup will drop open.
Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
15
To remove collected debris from Lint Screen, press the top release button and lift the handle to open. Gently brush the lint screen to clean.| To reinstall, place the bottom of the dust cup into the pod and then tilt until it clicks into place.

CLEANING AND REPLACING THE FILTERS

CLEANING FILTERS

Regularly rinse and replace the filters to maintain your vacuum’s suction power.
To prevent damage from cleaning chemicals, rinse filters with cold water only. Allow all filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into electric parts.

IMPORTANT: DO NOT use soap when cleaning the filters.

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
16

CLEAN PRE-MOTOR FILTERS EVERY 3 MONTHS
Remove Dust Cup , then lift out Filters.| CLEAN HEPA FILTER EVERY YEAR
Press the Filter Access button at bottom of the Filter Cover.
Tilt cover and lift out. Remove HEPA Filter.
To reinstall, insert the HEPA filter into the unit and replace the cover.

MAINTENANCE

Self-Cleaning Brushroll Technology
The self-cleaning brush roll actively removes hair wrap as you vacuum. If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught in the brush roll.

CLEANING THE BRUSH ROLL

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
17

To open the brushroll garage, slide both release buttons on the floor nozzle away from you, toward the back of the nozzle, then lift off the lid. Clear away any objects or debris.
To close the brush roll garage, insert the 3 tabs on top of the lid into the 3 slots in the nozzle, then push down on both sides of the lid until it clicks securely into place.

NOTE: If any hair is wrapped around the brush roll, extending the cleaning time will allow the self-cleaning brush roll to remove it for you. If some fibers remain wrapped around the brush roll after continued use, open the brush roll garage lid and carefully remove them.

CLEANING THE SOFT ROLLER

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
18| Shark ZU700 Performance Lift-Away®
Upright Vacuum - figure 19
---|---
To remove the Soft Roller from the nozzle, lift it out by the pull tab and tap off any loose debris. Use a dry towel to wipe the Soft Roller clean, or to remove any debris caught in the teeth behind it.| Hand washes the Soft Roller as needed. Use only water, and let air-dry completely for at least 24 hours. Reinsert the Soft Roller under the rubber bumper in the front of the nozzle until it clicks into place.

CHECKING FOR BLOCKAGES

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
20| Shark ZU700 Performance Lift-Away®
Upright Vacuum - figure 21
---|---
Detach the hose from the vacuum pod, and check the hose and opening on the back of the pod for blockages.| Detach wand from floor nozzle and handle, and
check both ends for blockages.
Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
23| Shark ZU700 Performance Lift-Away®
Upright Vacuum - figure 22
Detach wand from floor nozzle, tilt nozzle neck back, and check to open for blockages.| Detach handle from wand and hose from the vacuum pod, and check openings for blockages.

AVAILABLE ACCESSORIES

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
24

A Crevice Tool
This slender tool offers extended reach to access corners, baseboards, tight spaces, and ceilings.
B Dusting Brush
This brush dusts and cleans delicate surfaces. Great for use on fans, blinds, lampshades, and keyboards.
C Pet Power Brush
The turbine brush loosens and removes pet hair and debris from carpets, and powerfully deep-cleans dander out of upholstery and other surfaces.

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
26

D Duster Crevice Tool
Two cleaning tools in one. The crevice tool gives you extended reach to clean in tight spaces, while the soft brush is ideal for dusting delicate surfaces.
E Multi-Angle Dusting Brush
This brush dusts and cleans delicate surfaces. Great for use on fans, blinds, lampshades, and keyboards.
F Anti-Allergen Dust Brush
This brush features nylon fiber bristles specifically designed for removing fine dust and allergen particles from the most delicate surfaces.

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
25

G Upholstery Tool
Picks up pet hair, dust, and large debris from mattresses, couches, curtains, and other delicate upholstered surfaces.
H Wide Upholstery Tool
The wide cleaning path helps remove pet hair, dust, and large debris from mattresses, couches, curtains, lampshades, and other delicate upholstered surfaces.
I Pet Multi-Tool
A single convertible tool for cleaning tough pet messes two ways: use the stiff bristle brush to clean stuck-on debris, or take off the bristles to reveal an upholstery tool perfect for removing stubborn pet hair and large piles of debris.

Shark ZU700 Performance Lift-Away® Upright Vacuum - figure
27 J Under-Appliance Wand
Clean under and behind hard-to-move appliances and furniture with this adjustable 36” tool. Flip the extension piece over to clean the underside of the appliances.
K Home & Car Detail Kit
Deep-clean your cars like a professional detailer, or clean hard-to-reach areas in your home. Micro-sized tools let you clean around delicate objects and access the tightest spaces like car vents and computer keyboards.
L Accessory Bag
This convenient accessory storage bag measures 32 cm x 70 cm and fits the Under- Appliance Wand. The smaller size is available at sharkaccessories.com.

NOTE: Not all accessories come with all units. For a list of the accessories included with this model, see the top inside flap of the box. To order additional accessories, visit sharkaccessories.com.

TROUBLESHOOTING

The vacuum is not picking up debris. No suction or light suction.

  • Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the filters before reinserting them in the vacuum.
  • Dust cup may be full; empty dust cup.
  • Check hose, hose connections, nozzle, wand, pod, and accessories for blockages. Clear any blockages found. See the Checking for Blockages section for more information.
  • If any hair, string, or carpet fibers are wrapped around the brush roll, extend cleaning time to allow the self-cleaning brush roll to remove them. If some hair or fibers remain wrapped around the brush roll after continued use, remove the brush roll garage lid. Carefully clear away any debris or fibers. See the Cleaning the Brushroll section for more information.

Vacuum is hard to maneuver on high pile/plush carpets or lifts area rugs.

  • Make sure the selector switch is set to Hard Floor.
  • Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.
  • To minimize suction, slide the Suction Control collar to MIN.

Brushrolls do not spin.

  • If the brush roll indicator light turns red, turn off the power. Slide the Suction Control collar to MIN, then turn the vacuum back on.
  • If the brush roll indicator light is still red, there might be a clog. Immediately turn off and unplug the vacuum. Remove the pod from the floor nozzle and clear any blockages. Reconnect the nozzle, plug in the vacuum, and turn on the power.
  • With the power on, recline the handle, which will automatically activate the brush roll.
  • Ensure that the selector switch is set to Carpet for brush roll to spin.
  • If the brush roll indicator light is green and the headlights are flashing, this means that the brush roll garage lid is not properly closed. Press down firmly on both sides of the lid until it clicks into place.

The vacuum turns off on its own or the indicator light flashes red.
If your vacuum overheats, the thermostat will automatically turn off the motor. Follow these steps to restart:

  1. Turn the vacuum off and unplug it.
  2. Empty the dust cup and clean the filters. See Emptying the Dust Cup and Cleaning and Replacing the Filters sections.
  3. Check for blockages in hose, wand, nozzle, accessories, and inlet openings.
  4. Allow the unit to cool for a minimum of 60 minutes.
  5. Plugin the vacuum and press the selector button to turn it on.

For all other issues, please call Customer Service at 1-800-798-7398.

FIVE (5) YEAR LIMITED WARRANTY

The Five (5) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period of five (5) years from the date of purchase when it is used under normal  household conditions and maintained according to the requirements outlined in the Owner’s Guide, subject to the following conditions and exclusions:
What is covered by this warranty?

  1. The original unit and/or non-wearable components deemed defective, in SharkNinja’s sole discretion, will be repaired or replaced up to five (5) years from the original purchase date.
  2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.

What is not covered by this warranty?

  1. Normal wear and tear of wearable parts (such as foam filters, HEPA filters, pads, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
  2. Any unit that has been tampered with or used for commercial purposes.
  3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure to perform required maintenance (e.g., not cleaning the filters), or damage due to mishandling in transit.
  4. Consequential and incidental damages.
  5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja.
  6. Products purchased, used, or operated outside North America.

How to get service
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service Specialists are also available at 1-800-798-7398 to assist with product support and warranty service options, including the possibility of upgrading to our VIP warranty service options for select product categories. SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of $24.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.

How to initiate a warranty claim
You must call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of purchase. A Customer Service Specialist will provide you with return and packing instruction information.

How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

REGISTER YOUR PURCHASE

registeryourshark.com

Scan QR code using a mobile device

http://registeryourshark.com

Benefits of registering your product and creating an account:

  • Get easier, faster product support and access to warranty information
  • Access troubleshooting and product care instructions
  • Be among the first to know about exclusive product promotions

RECORD THIS INFORMATION

Model Number:………..
Serial Number:………….
Date of Purchase:……….
(Keep receipt)
Store of Purchase:………..
TECHNICAL SPECIFICATIONS
Voltage: 120V~ 60Hz
Watts: 900W

TIP: You can find the model and serial numbers on the QR code label on the bottom of the back of the vacuum pod.

PLEASE READ CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
This Owner’s Guide is designed to help you get a complete understanding of your new Shark® vacuum.
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
1-800-798-7398
sharkclean.com
Illustrations may differ from the actual products. We are constantly striving to improve our products; therefore the specifications contained herein are subject to change without notice.
For SharkNinja U.S. Patent information, visit sharkninja.com/uspatents

© 2020 SharkNinja Operating LLC. DUOCLEAN, LIFT-AWAY, and SHARK have registered
trademarks of SharkNinja Operating LLC.
ZU700Series_IB_E_MP_Mv1
PRINTED IN CHINA
Shark ZU700 Performance Lift-Away® Upright Vacuum - icon
3 @sharkcleaning

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals