ring 169AGBS Glass Break Sensor User Guide
- June 4, 2024
- Ring
Table of Contents
ring 169AGBS Glass Break Sensor ln-app Setup
- Make sure your Ring Alarm is disarmed.
- In the Ring app, open the menu. Tap Set Up a Device, then tap Security, tap Sensor, and find the Glass Break Sensor.
- Follow the in-app instructions to complete the setup.
Installation
We suggest mounting the Glass Break Sensor at least 7′ (2m) off the ground,
and close to your glass windows and doors.
Wall. Use the included mounting tape, clean the area, then peel the
backing and stick the Sensor. Press it to the wall and hold for 20 seconds to
make sure the tape is securely attached.
Ceiling. Use the included scrrews and anchors. First remove the back
cover and set the Sensor aside. Screw the back cover to the ceiling. To mount
the Sensor, twist it onto the back cover, and secure it in place.
- (2) screws included: 3×21 mm
- (2) anchors included: Sx25mm
Shelf. If mounting it on a shelf or piece of furniture, it does not need
to be attached. Just place it out of reach where it won’t be knocked
over.
For additional help, visit
ring.com/help
To download this manual, visit ring.com/alarm-manual For technical Z-Wave information, visit ring.com/z-wave
Ring LLC 1523 26th St. Santa Monica, CA 90404
© 2021 Ring LLC or its affiliates. Ring and all related marks
Important Product Information
Renseignements lmportants Relatifs au Produit
IMPORTANT PRODUCT INFORMATION
SAFETY INFORMATION
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC
SHOCK, OR OTHER INJURY OR DAMAGE.
WARNING: Your device should only be used in accordance with the specific
instructions for use and the intended purpose of the device. Using your device
in any way other than its intended purpose could cause injury to yourself,
others, and/ or damage to the device or property.
WATCH FOR SMALL PARTS! Your device and accessories may present a choking
hazard to small children. Keep them out of reach of small children.
CAUTION: The device is not waterproof and as such should not be submerged
in water, doing so could cause injury to yourself, others, and/or damage to
the device.
CAUTION: To reduce the risk of falling, take extra caution when using a
ladder or similar equipment to mount the product.
BATTERY SAFETY
This product contains alkaline batteries. This device requires batteries for
use. Only use new 1.SV alkaline AA-sized batteries. Never mix old and new
batteries. Keep all of the batteries out of the reach of children. Do not
open, disassemble, puncture, cut, bend, shred or heat the batteries and do
not allow metal objects to touch the battery terminals on the device as they
can become hot and cause burns. Remove all batteries if they are worn out or
before storing your Device for an extended period of time. Dispose of all
batteries in accordance with applicable laws and regulations and do not
dispose of batteries by throwing them into a fire. If any batteries begin to
leak, take steps to prevent the fluid from coming into direct contact with
skin or clothes as the fluid could be corrosive and may be toxic. Remove the
batteries and clean the battery compartment in accordance with the battery
manufacturer’s recommendations.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of the used batteries according to the manufacturer’s instructions.
Maintaining Your Ring Glass Break Sensor
The Ring Glass Break Sensor 1s for indoor use only. Use only accessories
supplied with your device, or specifically marketed for use with your device,
to power your device.
PRODUCT SPECIFICATIONS
Device Name: Ring Glass Break Sensor
Model Number: SC28S6
Electrical Rating: 3 AA Alkaline Batteries (1.SV)
Temperature Rating: 32°F to 120°F (0°C to 49°C)
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated Make
sure you dispose of, or recycle, your device in accordance with your local
laws and regulations. For information about recycling your device, go to
amazon.com/devicesupport.
Terms of Service and Warranty
By purchasing or using the product, you agree to the Terms of Service found at
ring.com/terms. For information on our warranty visit
ring.com/legal.
FOR CONSUMERS IN THE USA
Supplier’s Declaration of Conformity- Compliance Information Statement
Unique Identifier: Ring Glass Break Sensor
Model Number: 5C28S6
FCC ID: 2AB2Q5C28S6
Responsible Party and Party issuing Supplier’s Declaration of Conformity Ring
LLC, 1523 26th St., Santa Monica, CA 90404
www.ring.com / legal@ring.com
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class 8 digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Information Regarding Exposure to Radio Frequency Energy
The output power of the radio technology used in the Products is below the
radio frequency exposure limits set by the FCC. Nevertheless, it is advised to
use this product in such a manner that minimizes the potential for human
contact during normal operation. This device should be installed and operated
with at least 20 cm between the radiator and your body.
FOR CONSUMERS IN CANADA
Innovation, Science and Economic Development Canada (ISED) Compliance
IC ID: 10256A-5C28S6
This device contains license-exempt transmitter(s)/ receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Information Regarding Exposure to Radio Frequency Energy
This equipment complies with IC RSS-102 RF exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
References
- Amazon Digital Services and Device Support - Amazon Customer Service
- Get Smart Security With Ring Doorbells, Cams & Security Systems
- Ring Alarm Z-Wave Technical Information
- Ring: Security Systems, Cameras, Alarms, and Smart Home Automation | Ring
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>