CHORD ULTIMA 5 User Manual
- June 6, 2024
- chord
Table of Contents
**CHORD ULTIMA 5 User Manual
**
Safety instructions
Introduction
ULTIMA 5 is an incredibly reliable and technologically advanced stereo power
amplifier It is our most powerful stereo amplification offering within the
Full Size range.
Before operation, we strongly advise that you read this user manual
thoroughly, storing it in a safe place along with your original receipt of
purchase, in case you should require assistance in the futur.
Protection against liquids & heat
The ULTIMA 5 is not protected against liquids of any kind. Never place
containers of liquid on ULTIMA 5. Never allow ULTIMA 5 to come into contact
with moisture or liquids; doing so could result in electrocution or damage to
the ULTIMA 5 internal circuitry.
Be aware that liquids, including water that has dried, can leave minerals that
can affect the PCB and other components, which could eventually lead to
oxidisation and short-circuiting.
If the ULTIMA 5 comes into contact with moisture or liquids, immediately
disconnect from the mains power supply, an connected equipment, and contact
Chord Electronics for further advice.
The ULTIMA 5 has internal thermal
protection that will cut the power supply if reached.
Never operate the ULTIMA 5 near sources of heat or naked flames as this will
decrease the lifespan of the internal components. It is advised that you do
not operate the ULTIMA 5 in an area of direct sunlight or on top of
significant heat- producing devices.
Please be aware that it is entirely normal for the ULTIMA 5 to become warm
during use, particularly within a stacked configuration. If you are concerned
about thetemperatures, please switch the device off and consider a different
placement.
Dismantling & radio frequency interference
There are no userserviceable
components within the ULTIMA 5 or its power supply. Dangerous
voltages/currents exist within the ULTIMA 5 and its power supply, posing a
severe risk of electrocution and/or fire.
Never attempt to open, dismantle
or apply internal thirdparty devices to it or insert anything other than the
listed interconnects or speaker cables within this user manual.
If the ULTIMA 5 develops a fault or the casework becomes damaged, immediately
disconnect from the mains power supply and connected equipment and contact
Chord Electronics for further advice.
With a thick, solid aluminium chassis, the ULTIMA 5’s casework largely protects the sensitive internal circuitry from radio frequency interference. However,for optimal performance, it is recommended that the following points are observed:
Consider placing the ULTIMA 5 away from wireless routers.
Separate the ULTIMA 5 from amplifiers using toroidal transformers.
Operate mobile phones at a distance to avoid interference.
Although the ULTIMA 5 is largely shielded, it can generate radio frequency interference that may have an effect on radio and television reception. If this occurs, please reconsider your placement.
Connecting your equipment
Before connecting the ULTIMA 5 to any equipment, consult the manufacturer’s
user guide to confirm compatibility. When connecting the ULTIMA 5 to any
equipment, make sure that all devices are off, including the ULTIMA 5.
Once connected, switch all equipment on starting with the source and ending
with the amplification.
Initially, operate the any connected equipment on its lowest gain setting and
lowest volume setting, gently increasing to a comfortable listening level.
Never operate connected equipment to the ULTIMA 5 at excessive sound levels;
permanent hearing damage and loss can occur.
The included 15 amp IEC mains lead plugs into the ULTIMA 5.
If the power supply is prematurely disconnected ULTIMA 5 may still remain active for up to 15 seconds, however, this may cause damage toconnected equipment.
WARNING: Never disconnect the power cable during operation. Only
disconnect when ULTIMA 5 is off. If the power cable is disconnected during
operation there is a risk of damage to connected equipment.
Warranty
Warranty period & registering your purchase
At point of sale, Chord Electronics Ltd. provides ULTIMA 5 with a
comprehensive five-year warranty which covers defects in materials and
workmanship through fair wear and tear. The warranty will be void if any other
PSU other than that supplied is used.
The warranty is transferable with proof of purchase, however, warranty on ex-demonstrationunits begins from the retailer‘s date of purchase.
Please use the form below to record the details of your purchase in the event
that these are required at a later date, we further advise that all
purchasesare registered with Chord Electronics at: chordelectronics. co.uk
/register-product/
RETAILER:
|
---|---
PURCHASE PRICE:
|
UNIT COLOUR:
|
DATE OF PURCHASE:
|
TRANSACTION ID|
Making a claim & warranty exclusions
In the unlikely event of a claim, you must provide Chord
Electronics with the details of the claim, including your original proof of
purchase and serial number in order to validate the nature of the repair.
Upon receipt, Chord Electronics will make an assessment within 30 days and
provide a reasonable solution.
All warranty repairs must be carried out by Chord Electronics or an approved
service centre to guarantee the quality and safety of the repair.
WARRANTY EXCLUSIONS: The warranty does not cover connected equipment,
personal injury or development natural patina of the metalwork and will be
null and void if the following is applied: wilful neglect; modification or
tampering of the product; improper use of the product; acts of God; damage
caused by a connected device; mechanical shock; fire or application of
excessive heat or repair/modification by a nonauthorised third-party vendor.
Getting to know ULTIMA 5
Getting to know ULTIMA 5
Before operation, we strongly advise you read this user manual thoroughly,
storing it in a safe place along with your original receipt of purchase,
should you require assistance in the future.
The front panel
With only two buttons, everyday operation of ULTIMA 5 is simple and you can tailor the brightness of the feature lighting to suit the ambience of your listening room. Please view page 23 to learn how to do this.
WARNING: You must keep all vents clear.
The top panel
The top panel has no user configurable options. Instead, three teal feature light rings illuminate. If you find that these rings are too bright for your listening room you can control the brightness via the front panel.
WARNING: You must keep all vents clear
The rear panel
The rear panel offers a comprehensive connectivity suite, featuring both
standard connections and those which are used with other Chord Electronics’
devices.
When installing any cable, you must make sure that they securly click into
place, especiallyoptical.
Setting up ULTIMA 5
Placement
Whilst ULTIMA 5 will operate normally within a typical Chord Electronics
configuration, stacked via the Integra legs, it is recommended that ULTIMA 5
is allowed to ‘breathe’ with 10cm of space around it to convectioncool during
operation.
Connecting ULTIMA 5 to ancillary equipment
When connecting the ULTIMA 5 to equipment within the signal path, ensure all
devices are switched off. It is recommended that once all equipment is
properly connected, that the volume setting is operated to its lowest setting,
before slowly being raised to a comfortable listening level. Always observe
partnering manufacturers’ guidelines.
Audio inputs
ULTIMA 5 is equipped with both balanced XLR inputs aswell as unbalanced RCA inputs.ULTIMA 5 has no ability to switchbetween the inputs therefore,only one must be used.
WARNING: ULTIMA 5 must be connected to a dedicated preamplifier, or a device capable of attenuating its output. Failure to attenuate the volume before it enters ULTIMA 5 could result in irreversible hearing damage, speaker damage and couldvoid the warranty.
Audio outputs
As ULTIMA 5 is a stereo amplifier, it supports 2 speaker outputs. In order to connect ULTIMA 5 to loudspeakers, use high-quality loudspeaker cable terminated with 4mm banana plugs or 6mm spades. Bare wire can be used, but it is not recommended.
Connect the black (negative) terminal from ULTIMA 5 to the negative terminal on your loudspeaker and the red (positive) terminal from ULTIMA 5 to the red positive terminal on your loudspeaker. Please pay careful attention to the diagrambelow when plugging in your speakers.
WARNING: Please pay attention to the polarity on your speakers and the layout of the Ultima 5 outputs. Ensure thatall wires are correctly placed.
Power-on sequence and 12V trigger
POWER-ON SEQUENCE: During
normal operation, when ULTIMA 5 is in standby mode the large power button on
the front panel will illuminate an red colour. To power-on ULTIMA 5 press the
large power button once until you feel a click. ULTIMA 5’s power button will
now change to a green colour whilst it begins its initial safety checks.
During this phase do not increase the gain on the input device as you cannot
determine its final amplified volume which can damage the connected speakers.
Once the amplifier has passed the safety check and is operational, after
approximately ten seconds, the amplifier will display a teal colour.
12V Trigger: A 12V trigger can be used to remotely turn ULTIMA5 on or off.
Please refer to the below diagram to correctly wire your 12V trigger. When a
12V trigger is sensed by ULTIMA 5 the colours displayed on power button will
be different.
During standby the large power buton on the front panel will illuminate an
orange colour, however just like the power sequence without the 12V trigger a
green colour will be displayed once you switch the unit on andit performs its
safety checks. Youshould still not increase the gainv on the input device.
Once the amplifier becomesoperational the power button will display a
continuious purple glow.
WARNING: In the rare event that a fault is detected the amplifier will
switch itself off. If this occours discontinue use immediately and seekhelp
from your Chord Electornics retailer.
Earthing issues in Europe
In some European countries, a hum
or buzz may occur if the amplifier is connected to mains sockets that do not
have an earth or adequate earth. If this occurs, please ensure that your
equipment is connected via a good-quality multi-way mains block which contains
an earth point at every socket outlet.
We recommend that an earthing method for your building is implemented.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>